2019 Audi A7 Quattro Cooling and Climate Controls

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

• Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
• Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
• All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
• All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

A/C O-Ring

ACM is a supplier of Original Equipment quality climate control products. 13.7×2.5mm Miscellaneous Locations Through Out A/C System

ACM is a supplier of Original Equipment quality climate control products. 11×2.5mm

Carquest Premium Blower Motors are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile A/C experience, fix it once and fix it right with Carquest Premium Blower Motors. Meets or exceeds OE design. Magnetic size and properties compare or exceed OEM. Windings meet or exceed OEM Specifications. Motor RPM equivalent to or exceeds OEM motor.

Product Features:

• Meets or exceeds OE design and performance
• Magnetic size and properties compare or exceed OEM
• Windings meet or exceed OEM specifications
• Motor RPM equivalent to or exceeds OEM motor
• Functionally Equivalent to OE Design
• Magnetic size and properties compare or exceed OEM
• Hermetically Sealed & Thermally Protected Electronics

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

• High grade stainless steel and copper construction
• Meets or exceeds OEM standards
• Consistent and precise response to cooling system needs
• Original equipment design for worry-free direct fit replacement
• 100% tested and calibrated

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

• High grade stainless steel and copper construction
• Meets or exceeds OEM standards
• Consistent and precise response to cooling system needs
• Original equipment design for worry-free direct fit replacement
• 100% tested and calibrated

We are proud to offer this CARQUEST product line: CARQUEST Water Outlets. Our products are engineered and tested to provide years of trouble free operation and designed to be hassle free OE replacement part that meets and/or exceeds OE standards. Backed by over 50 years of mobile temperature control experience, fix it once and fix it right with CARQUST Water Outlets and Thermostat Housings.

Product Features:

• Meets and/or exceeds OEM standard
• Includes quality gasket or O-ring to ensure proper seal (where applicable)
• 100% virgin resin material to insure durability
• 100% leak tested
• Direct-fit replacement for ease of installation

Rein Automotive OE quality thermostat assemblies install, fit and perform the way the original manufacturer intended. This ensures a smooth and easy installation, just as one would expect to find with OE quality. These assemblies are designed to meet or exceed the OE materials used. Rein thermostats are produced with high-quality metals and components to ensure proper durability and service life. The thermostats are temperature calibrated to have a consistent and precise response suiting cooling system needs. Our quality thermostat assemblies aim to provide the professional repair technician and vehicle owner peace of mind and trust that is expected from an OE quality component

Product Features:

• Matches Original Equipment design specifications
• Direct fitment allows easy installation
• Manufactured to strict engineering standards/specifications in materials and tolerances
• Made by the OE manufacturer

This replacement engine coolant thermostat housing assembly is engineered to match the fit and durability of the stock housing assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

• Ideal replacement – this engine coolant thermostat housing assembly directly replaces the original water outlet on specified vehicle years, makes and models
• Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
• Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
• Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housing assemblies

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• Designed to OE standards for ease of installation
• In manufacturing, we custom form the wax pellets for different temperature range specifications. All units are calibrated & tested to confirm switch actuation at their specified temperature
• The switch is designed using a formed bimetallic contact arm. The bimetal contact movement is achieved using the different expansion rates of two metals fused together. This is a creep action device, provides precise performance
• In production, all thermal switches are factory-calibrated to make electrical contact at the specified lower-temperature set point
• Robust design and high grade materials meet the stringent demands of today’s service professional

Water Temp. Sensor

Oil Drain Plug Gaske

Auxiliary Water Pump

Auxiliary Water Pump

The product selection from Pierburg Pump Technology covers the complete range of applications for electric water circulation and coolant pumps in the automotive industry. Pierburg has extensive experience in the area of electric water pumps, especially with regard to EC engine technology and hydraulics. The canned motor concept was selected to meet the high requirements for operational reliability and service life. This special motor design has an additional tube placed in the space between the stator and the rotor, which keeps the stator statically sealed with respect to the medium pumped by the running rotor. Since this drive system requires no dynamic sealing elements which are subject to wear (rotating mechanical seals), the water circulation and coolant pumps are especially reliable and free of wear problems. Moreover, the EC motor used in the pumps requires no brushes. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Reduction in noise
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• Water circulation pump can deliver as much as 800 liters per hour
• Coolant pump can deliver more than 9,000 liters per hour

The product selection from Pierburg Pump Technology covers the complete range of applications for electric water circulation and coolant pumps in the automotive industry. Pierburg has extensive experience in the area of electric water pumps, especially with regard to EC engine technology and hydraulics. The canned motor concept was selected to meet the high requirements for operational reliability and service life. This special motor design has an additional tube placed in the space between the stator and the rotor, which keeps the stator statically sealed with respect to the medium pumped by the running rotor. Since this drive system requires no dynamic sealing elements which are subject to wear (rotating mechanical seals), the water circulation and coolant pumps are especially reliable and free of wear problems. Moreover, the EC motor used in the pumps requires no brushes. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Reduction in noise
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• Water circulation pump can deliver as much as 800 liters per hour
• Coolant pump can deliver more than 9,000 liters per hour