2015 Land Rover Discovery Sport Engine Cooling Parts

The Graf Water Pump contains no remanufactured parts and is produced using an optimized all metal impeller design to assist in cooling under high RPM, and performance demands. Selection of raw materials, reliability of machinery and production processes, stringent controls throughout the production process, from melting to fitting, as well as reliability tests performed using equipment able to determine true performance, go to ensure this product is a real guarantee of safety and long life. The Graf water pump is centrifugal in type and comprises a bladed rotor linked by means of a shaft (which rotates on bearings housed in a support) to the drive gear; the seal between the pump and the motor block is guaranteed by a gasket, while the inside of the pump is guaranteed by a mechanical seal. Component parts: Impeller: supplies the fluid with the necessary energy to cover the entire cooling circuit. Mechanical seal: ensures fluid seal inside the pump. Bearing: transmits movement to the impeller and supports any ventilation parts. Entrainment part: for transmitting movement to the bearing. Pump body: supports the basic pump component parts and conveys the coolant in the motor block.

Product Features:

• All the component parts fitted are pre-tested to evaluate durability, performance and reliability.
• The bearings undergo a durability test equivalent to nominal lifespan and are then inspected to assess integrity.
• The mechanical seals are tested in extreme coolant temperature conditions according to predefined cycles.
• The shape of the impellers is optimized thanks to the use of prototypes on which flow and performance tests are performed.
• On both the entrainment parts and the bodies, the choice of materials and/or technologies different to original ones is made on the basis of structural and mechanical tests.
• After assembly all the pumps undergo seal tests on units that reject those with leaks above set limits.

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

• High torque and rigidity
• Sensor-safe, non-corrosive formula
• OEM specified
• Low-odor, non-corrosive formula
• Ideal for closed spaced bolt patterns

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

• Ideal for rigid cast aluminum parts
• Meets OEM Specifications
• Sensor safe & non-corrosive
• Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
• Blowout resistant, allowing leakproof gaskets to be made in just one minute
• Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
• Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
• Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
• Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings. Permatex Water Pump & Thermostat has the highest water-glycol resistance available in an RTV silicone.

Product Features:

• Sensor-safe, noncorrosive RTV silicone gasket material
• Formulated specifically for water pumps and thermostat housings
• Highest water-glycol resistance available in RTV silicone
• Superior adhesion and flexibility
• Can be used as a gasket maker or dressing

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

• Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
• Sensor-safe, non-corrosive, RTV silicone
• Protects against leaks caused by vibration and thermal expansion
• Meets performance specs of OE silicone gaskets
• Quickly returns vehicle to service in just 1 minute

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

• Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
• Sensor-safe, non-corrosive, RTV silicone
• Protects against leaks caused by vibration and thermal expansion
• Meets performance specs of OE silicone gaskets
• Quickly returns vehicle to service in just 1 minute

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

• High torque and rigidity
• Sensor-safe, non-corrosive formula
• OEM specified
• Low-odor, non-corrosive formula
• Ideal for closed spaced bolt patterns

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

• Thermal tested under real-life temperature simulations
• High tensile strength aluminum for maximum crimp strength
• Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
• Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
• Oil cooler designs meet or exceed OE standards, keeping the vehicle’s engine and transmission performing at optimal conditions
• OEM grade, premium fittings for transmission or engine oil coolers (where applicable)

New Platinum Pro Radiator

Product Features:

• Made Of Plastic and Aluminum
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle

Manufactured to meet all OEM specifications. Designed to be easy to install and remove. Manufactured from high quality components with proper relief and vacuum valves. Quality tested to stand up to even the most demanding automotive cooling systems.

Product Features:

• Maintains proper cooling system pressure
• Easy installation and removal
• 100% tested to ensure proper pressure and longevity
• Meets all OEM specifications

Rein Automotive OE temperature sensors are made to factory specifications ensuring proper fit, form and function. The temperature sensor is used to report exhaust temperatures to the vehicle’s ECU. The vehicle uses this information to control engine and emission paramaters. Rein temperature sensors include a vehicle specific connector that fits directly into the factory plug.

Product Features:

• Direct OE replacement
• Designed to meet or exceed factory specifications
• Made using high quality materials
• Uses vehicle specific style connector for quick replacement.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Coolant Level Sensor

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

• High grade stainless steel and copper construction
• Meets or exceeds OEM standards
• Consistent and precise response to cooling system needs
• Original equipment design for worry-free direct fit replacement
• 100% tested and calibrated

This replacement engine coolant thermostat housing assembly is engineered to match the fit and durability of the stock housing assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

• Ideal replacement – this engine coolant thermostat housing assembly directly replaces the original water outlet on specified vehicle years, makes and models
• Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
• Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
• Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housing assemblies

Thermostat Assembly