from

$20.42

Differential Side Cover Seal, 90 x 44 x 10

from

$17.00

Trans Case Output Sh

from

$36.99

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON®, GM DEXRON®-II and DEXRON®-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III , Toyota/Lexus Type T, T-III and T-IV , Honda/Acura ATF-Z1 (except in CVTs) , Mercedes Benz NAG1 , Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$99.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to BMW 04-10;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 2004-2010
Weight approx: 1 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 2.00 INCH / 51 MM
MOUNT WIDTH: 6.30 INCH / 160 MM

from

$517.88

GKN Drivetech (Lobro) manufactures a replacement Axle Assembly that is optimized for weight, noise, vibration, harshness (NVH), steering and suspension performance.

Product Features:

OEM Quality and a Direct fit Replacement
Provides exceptional reliability.
Improved space utilization through power unit and gearbox repackaging potential.
Lighter weight provides improved fuel efficiency.
Better driving characteristics and comfort
Optimum power delivery for peak vehicles

from

$23.99

Product Features:

Brand may vary by location

from

$925.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints..

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$627.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation
All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance

from

$664.99

Rein Automotive OE quality transfer case actuators are made to factory specifications ensuring proper fit, form and function. The transfer case actuator is a small motor attached to the case that proportions engine power to the front and rear differentials. High quality electronics and nylon gears are used to ensure a long service life. Our quality transfer case actuators aim to provide the professional repair technician and vehicle owner the peace of mind and trust that is expected from an OE quality component.

Product Features:

Rein OE quality transfer case actuators are the perfect replacement to meet the high demands placed on 4WD/AWD systems.
Direct OE replacement including mounting hardware.
Designed to engage or disengage the four wheel drive system as selected by the ECU of the vehicle.
Manufactured using high quality materials.
Restores functionality of 4WD/AWD system.

from

$668.20

Transfer Case Motor

from

$7.99

Rein Automotive OE quality oil drain plugs are made with premium materials and designed and manufactured to be direct-fit replacements. Rein oil drain plugs are designed to tight tolerances to ensure proper sealing.

Product Features:

Designed to tight tolerances to ensure proper sealing.
Rein Oil Drain Plugs are coated for high corrosion resistance.
Designed and constructed to strict engineering quality standards.
Includes copper sealing gasket.

from

$63.15

With Clamps and Grease SPIDAN and LOBRO boots are specifically developed for the various joints – their accurate fit ensures optimum sealing of the joint. Up-to-date computerized equipment is used for the production of the boot.

Product Features:

For every specific application a boot kit to the OES standard
Reliable protection against damp and dirt
Optimum sealing and abrasion resistance
Manufactured according to DIN EN ISO 9001:2000

from

$33.01

With Clamps and Grease The Vaico CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$12.32

The Febi Axle Shaft Nut is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$3.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$20.29

Input Shaft Seal

from

$18.55

Input Shaft Seal

from

$111.58

Driveshaft Flex Join

from

$64.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$22.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National