from

$149.99

New Platinum Pro Radiator, 2.0 Liter L4 Turbo, 3.0 Liter L6 Turbo Gas Engines Only, With Automatic Transmission, Without Sulev Emissions Package

Product Features:

2.0 Liter L4 Turbo, 3.0 Liter L6 Turbo Gas Engines Only, With Automatic Transmission, Without Sulev Emissions Package, Made Of Plastic and Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$85.99

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

from

$28.49

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

Ideal for rigid cast aluminum parts
Meets OEM Specifications
Sensor safe & non-corrosive
Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
Blowout resistant, allowing leakproof gaskets to be made in just one minute
Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

from

$147.99

HEATER CORE

from

$25.99

Crafted to meet the exact specifications set by Original Equipment Manufacturers (OEM), these products are engineered for effortless installation and removal. Constructed from premium-grade components, incorporating proper relief and vacuum valves, they ensure optimal performance even in the most demanding automotive cooling systems. Rigorously quality-tested, these components provide exceptional, out-of-the-box performance and superior durability to meet or exceed the highest standards of today’s vehicles.

Product Features:

Maintains proper cooling system pressure
Easy installation and removal
100% tested to ensure proper pressure and longevity
Meets all OEM specifications

from

$25.60

Coolant Level Sensor

from

$153.77

Intelligent control systems from MAHLE are used in millions of applications worldwide to provide needs-based precision temperature control. Simple, effective, and tried and tested millions of times over: thermostat inserts from MAHLE provide meticulous regulation of coolant circuits around the world up to approximately 20 m3/h, and ensure ideal operating temperatures in light vehicles, trucks, stationary engines, and also agricultural and construction machinery. Wax elements are at the heart of all MAHLE thermostats and thermostat inserts. These maintenance-free, durable elements have proved their worth in millions of applications. MAHLE, Manufactures a wide range of variants with actuating forces of between 30 N and 2,500 N, small or large displacements, and for a large number of regulation ranges within a temperature span of -20C to +130C.

Product Features:

OE quality and design
Maintenance-free, durable elements

from

$38.49

Controls the operating temperature of Imperial electric fans. Operates up to 2 fans.

Product Features:

Preset thermostatic fan control
185°F preset
For use with Imperial electric fans
Probe installs into radiator fins

from

$4.99

This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:

Ideal replacement – this engine coolant bleeder screw matches fit and function of the original equipment screw
Durable materials – designed to withstand high cooling system temperatures and pressures
Cost-effective solution – this bleeder screw offers original equipment quality at a competitive price
Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

from

$78.99

Carquest Premium Blower Motors are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile A/C experience, fix it once and fix it right with Carquest Premium Blower Motors. Meets or exceeds OE design. Magnetic size and properties compare or exceed OEM. Windings meet or exceed OEM Specifications. Motor RPM equivalent to or exceeds OEM motor.

Product Features:

Meets or exceeds OE design and performance
Magnetic size and properties compare or exceed OEM
Windings meet or exceed OEM specifications
Motor RPM equivalent to or exceeds OEM motor

from

$146.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$11.49

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$67.99

Electric fan with 10″ diameter. Imperial electric fans are reversible for push or pull operation and are designed with a thin, aerodynamic profile for applications with limited space.

Product Features:

Rapid-Cool® Thin-Line electric fans
10″ Diameter
650 CFM
Use as a pusher or puller fan

from

$91.99

New CAPA Certified Standard Replacement Radiator Support Upper Support Panel, Made Of High Strength Steel

Product Features:

Made Of High Strength Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$68.99

Carquest Accumulators and Receiver Driers are designed to store, filter and dry the air conditioning refrigerant to provide proper performance and durability for the air conditioning system. They are manufactured to meet or exceed original equipment specifications.

Product Features:

All parts meet or exceed original equipment standards for moisture absorption, pressure and temperature resistance, air tightness, vibration resistance, corrosiveness, and pulse pressure.
Desiccant is 100% tested and assembled in a controlled environment to ensure performance meets or exceeds original equipment standards.
All accumulators and receiver driers are helium leak tested prior to packaging.
O-Rings necessary for installation are included.

from

$558.99

Carquest Premium A/C compressors are 100% new units that are manufactured to the highest quality to meet or exceed OE specifications.

Product Features:

Every unit is 100% function and leak tested
Tested for noise, vibration, durability, vacuum decay and pressure decay to ensure no leaks and longer life
Very low friction coating used on swash plate to improve durability
PTFE coated pistons improve performance and reduce wear
Rubber dampened clutch plate ensures smooth clutch engagement and reduces wear
Matched high-quality needle-roller bearing ensures low friction and high load capability
Limited Lifetime Warranty when following warranty requirements: Flush A/C System, replace accumulator/receiver dryer, replace orifice tube/expansion device, and filling with correct oil and refrigerant

from

$155.99

This replacement engine coolant reservoir is manufactured from quality materials to withstand the stresses of underhood heat and engine vibration. It is engineered and manufactured to match the fit and function of the original part..

Product Features:

Direct replacement – this engine coolant reservoir matches the fit and function of the original part.
Ideal solution – engineered for a seamless installation
Durable construction – manufactured from quality materials to withstand underhood heat and vibration
Trustworthy design – backed by 100 years of automotive aftermarket experience

from

$29.54

A/C Pressure Switch

from

$48.99

New CAPA Certified Standard Replacement Radiator Support Panel Brace, Center Brace, Made Of Aluminum

Product Features:

Center Brace, Made Of Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$25.99

Delphi temperature sensors are built with the latest OE technology; Delphi temperature sensors use durable, one-piece design; Delphi temperature sensors are impervious to electrical noise and interference.

Product Features:

Delphi temperature sensors deliver accurate readings and optimal performance
Delphi’s one-piece design and automated production process eliminates internal connectors and failure points
Each sensor is electrically insulated to eliminate interference from other components in the vehicle
Delphi temperature sensors are impervious to electrical noise and interference

from

$265.99

ABS Wheel Speed Sensor

from

$204.99

Carquest premium direct replacement resistors are designed to match the operation and performance of the original equipment to restore the proper heating and cooling functionality.

Product Features:

Restores Functionality- Manufactured to original equipment specifications to restore full HVAC operation
Original equipment quality – Carquest blower motor resistors meet the high quality material standards and tolerances as the original equipment
Complete kit – Each kit includes the resistor, connector, and splice connectors to complete the job
Direct replacement – Carquest blower motor resistor kits are a direct replacement to the original equipment resistor

from

$1.55

Air Conditioning O-Ring

from

$51.99

Carquest Expansion Valves are designed to regulate the flow of refrigerant through the air conditioning system to provide optimal cooling to the passenger compartment. Each expansion valve is manufactured to original equipment specifications to perform its function even in the harshest climates. Each part is supplied with the necessary gaskets and o-rings for installation.

Product Features:

The bodies of these expansion valves are machined from a single block of aluminum or brass metal.
Each expansion valve has settings for tonnage and superheat based on the vehicle specifications.
Each expansion valve is tested for function and leakage according to OEM specifications to ensure optimal performance of the air conditioning system.
O-Rings necessary for installation are included.

from

$178.99

The Carquest condenser is an integral component of the motor vehicle air conditioning system. This part condenses the refrigerant into a liquid to prepare it for entry into the compressor. The condenser is manufactured according to OEM design specifications to ensure a long life with quality performance. Exact design standards produce a seamless fit into the engine compartment.

Product Features:

This is a parallel flow condenser that contains small micro-channels. It is highly recommended that this condenser be replaced if a failure has occurred in the vehicle’s air conditioning system that has resulted in debris contaminating the system. This
This Carquest condenser has a drier attached to it with an interior desiccant bag which will provide optimal moisture removal in the a/c system to maximize cooling performance.
The Carquest condenser production process includes quality driven details such as using zinc-coated tubes and electrostatic paint spray at high temperatures to provide the best corrosion resistance and durability in our condensers.
Continuous molds, laser welding machines, semi-automatic assembly stations and other advanced equipment provide quality products.
Each condenser uses only the highest quality raw materials including pure aluminum (not substandard or recycled) to provide the highest quality standards from beginning to finished product.
All brackets are designed per OEM specifications to ensure strength and reduce vibration and movement.
We leak test 100% of our condensers in helium leak test chambers to ensure the product does not leak.
Our condensers are manufactured from rigid design standards to fit OEM dimensions.
Each condenser design endures a series of tests that includes performance testing, vibration testing, blast testing, and salt spray testing to simulate real world conditions.
Each Carquest condenser is packaged using superior box construction. This box is easy to open and seal. Each condenser is packaged in the box with internal protection to keep the part centered and away from the package edges. The package passes the fre
All brackets are designed per OEM specifications to ensure strength and reduce vibration and movement.
We leak test 100% of our condensers in helium leak test chambers to ensure the product does not leak. This industry leading process is the most precise method and can detect even the smallest leak. The leak-free condenser is then charged with nitrogen and
Our condensers are manufactured from rigid design standards to match OEM dimensions. Each design undergoes a drop fit into the actual vehicle to ensure the final manufactured product provides an easy installation.
Each condenser design endures a series of tests that includes performance testing, vibration testing, blast testing, and salt spray testing to simulate real world conditions.
vibration testing
blast testing
and salt spray testing to simulate real world conditions.

from

$195.80

BEHR manufactures an OE-equivalent direct fit A/C Condenser that guarantees the same high quality, fit and performance of the OEM A/C condenser it replaces. BEHR produces brazed flat-tube condensers, delivering high power in spite of their small package size. This ensures rapid cooling of the vehicle cabin, thanks to optimum matching of heat transfer and pressure drop on the coolant side and air side.

Product Features:

OE-Equivalent and Direct fit Application.
Advanced technology parallel flow, sub cool and serpentine design.
Provides the fit, quality and performance of the original equipment.
compliant for both R12 and R134A refrigerants.

from

$608.99

As one of the world+s largest OE suppliers of A/C compressors DENSO units are specified by most major vehicle manufacturers. DENSO First Time Fit A/C compressors are manufactured and tested to the strictest OE standards for unparalleled performance. At DENSO we bring together everything we know as an air conditioning systems manufacturer to bring you the highest quality line of factory-new compressors available. When it comes to new compressors you can’t do better than going with a unit manufactured by the OE supplier. At DENSO we know these units better than anyone because we originally designed them. Our compressors are built to meet DENSO+s unsurpassed reputation for technological superiority. You can relax knowing DENSO will give you the right part and the right fit the first time.

from

$641.99

Carquest New Compressors are designed, manufactured and tested to meet or exceed strict original equipment specifications for superior quality and performance. Each new compressor is tested to provide durable life to the vehicle’s air conditioning system. All new compressor components are assembled using state of the art equipment and techniques to ensure smooth operation. Each part is equipped with a clutch and connector that matches the original equipment part and provides an exact replacement to your vehicle’s part. All compressors are supplied with the necessary gaskets and o-rings for installation.

Product Features:

Each new compressor design undergoes rigorous life cycle testing at high RPMs and pressures to ensure that they can withstand years in the harshest conditions.
New compressors are designed with utmost precision using 3D coordinate measuring machines to ensure a perfect fit.
The production process contains automated controls at every stage that alerts and halts production in case of an error, assuring that the finished product will always be flawless.
All new compressors must pass a helium leak test and pump up function test prior to packaging.
O-Rings and gaskets necessary for installation are included.