from

$6.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Manufactured for the sealing repair environment
Validated for fit, form, and function
Unsurpassed quality you can trust

from

$30.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$604.99

New Standard Replacement Front Radiator Support

Product Features:

Made Of Steel
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$40.99

Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.

Product Features:

Machined metal construction
Works with MT-300 pressure tester
Tests coolant caps
Professional quality

from

$60.99

Driveworks Water Pumps offer a complete replacement part solution, with application coverage that spans from antique to present-day vehicles. All units are 100% tested and engineered to meet or exceed OEM performance, providing you a quality product you and your vehicle can rely on. All units are manufacturered with brand new components and are packaged with all gaskets required for replacement.

Product Features:

100% Factory tested for leakage and dimensional precision
Manufactured to original casting specifications to ensure a proper fit and proper water flow for efficient cooling
Bearings made of heat-treated carbon or carburized steel are sealed and lubricated to ensure smooth performance throughout units life
Assembled with new, high-quality unitized shaft seals to prevent premature leakage
Supplied with gasket and other seals/gaskets as applicable per application to help complete the job
This pump is driven by the accessory belt and we recommend replacement if nearing service recommendation

from

$28.49

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

Ideal for rigid cast aluminum parts
Meets OEM Specifications
Sensor safe & non-corrosive
Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
Blowout resistant, allowing leakproof gaskets to be made in just one minute
Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

from

$83.99

Replace your damaged cooling fan blade with this direct replacement. This vehicle-specific application is engineered for a perfect fit and is made from quality materials to ensure durability and restore proper cooling system operation.

Product Features:

Direct replacement – this engine cooling fan blade fits and functions like the original equipment fan blade
Quality construction – manufactured from premium materials for a long service life
Excellent value – original equipment quality at a lower price
Quality tested – has undergone testing to ensure proper fit and performance

from

$10.70

The Motorcraft Original Equipment Radiator Cap is an OES replacement component that provides the same performance, durability, and service life as your factory original equipment.

Product Features:

Standard and safety vent radiator pressure caps available
Extensive coverage for most cars and trucks, as well as farm and construction equipment
Swivel-seal radiator caps are designed to provide increased durability and can be removed without damage to the rubber atmospheric seal
Zinc-plated to resist corrosion and rust
Pressure valve springs are made of stainless steel to maintain calibrated pressure throughout the service life
Rubber pressure valve gasket resists high temperatures and deterioration from coolant and additives
Pressure and vacuum relief features help extend radiator and hose life
Prevent accidental cap removal with positive low-pressure stop feature

from

$2.59

This radiator drain petcock is a direct replacement for the original equipment plug that may have deteriorated or corroded. Made of quality materials, this petcock is engineered to strict standards for durable use over time.

Product Features:

Direct replacement – this radiator drain petcock matches the fit and function of the original equipment part
Durable construction – this part is made of quality materials for a long service life
Saves money – offers original equipment quality at a competitive price
Quality assured – this petcock has undergone virtual testing to assure proper fit and function

from

$19.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute

from

$9.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$109.99

US Motor Works Professional Series Water Pump with Fan Clutch are designed to replace the mechanical components of a cooling system. A proper water pump replacement should include a new fan clutch as the two are connected to the same shaft and work together to move the air and cooling fluid. Replacing one without the other can damage the new part and cause repeat work or engine trouble. This matched set will allow your vehicle continued operation in the demanding environment of today’s engine. All components are brand new and QA inspected for perfect fit and function. Restore your cooling power by installing a US Motor Works Professional Series Water Pump with Fan Clutch.

Product Features:

Fan clutch mounts to the water pump and should be replaced at the same time.
Matched set for proper water pump or fan clutch replacement
Includes mounting hardware, gaskets and accessories as required.
Complete mechanical cooling parts replacement
Factory tested and 100% new product
Meets or exceeds OEM quality

from

$51.99

We are proud to offer this CARQUEST product line: CARQUEST Water Outlets. Our products are engineered and tested to provide years of trouble free operation and designed to be hassle free OE replacement part that meets and/or exceeds OE standards. Backed by over 50 years of mobile temperature control experience, fix it once and fix it right with CARQUST Water Outlets and Thermostat Housings.

Product Features:

Meets and/or exceeds OEM standard
Includes quality gasket or O-ring to ensure proper seal (where applicable)
Coated with corrosion and rust inhibitor
100% leak tested
Direct-fit replacement for ease of installation

from

$99.99

Product Features:

Motors built and tested to quality specifications
14 in. universal fit reversible fan
1250 CFM
UNIVERSAL fan, NOT a direct OE replacement. Measure core and verify space.

from

$192.14

The Motorcraft fan clutch is built with the knowledge and experience that only comes from being the original equipment (OE) manufacturer.

Product Features:

Fan clutch design operates more efficiently than thermal bi-metal spring fan clutches
Direct replacement for a proper fit every time
Quality tested to ensure trouble-free installation and performance

from

$26.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$3.89

Thermostat O-Ring

from

$1.41

Water Pipe O-Ring

from

$6.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design
Manufactured for the sealing repair environment
Validated for fit, form, and function
Quality that you can trust

from

$8.15

Coolant Crossover Pi

from

$19.12

Re-engineered to address common failure points in the original equipment, Dorman’s Engine Coolant Thermostat Housing has improved durability and resistance. It withstands the extreme changes in temperature that frequently cause housing to become brittle, crack and leak. This is more than a replacement; it’s an upgrade. Maintain the steady flow of coolant and lessen the chances of overheating.

Product Features:

Direct replacement for a proper fit every time
Hoses slide on for easy installation
High-quality plastic or metal construction
Includes all hardware necessary for a complete repair (where applicable)

from

$32.99

Kit includes thermostat, housing, and all necessary seals/gaskets to do the complete job. These individual parts are manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat and housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$98.99

This replacement engine coolant reservoir is manufactured from quality materials to withstand the stresses of underhood heat and engine vibration. It is engineered and manufactured to match the fit and function of the original part.

Product Features:

Direct replacement – this engine coolant reservoir matches the fit and function of the original part
Ideal solution – engineered for a seamless installation
Durable construction – manufactured from quality materials to withstand underhood heat and vibration
Trustworthy design – backed by 100 years of automotive aftermarket experience

from

$481.54

Radiator

from

$96.99

Product Features:

Designed, tested, and built by application
OE performance, fit, and appearance
Precision machined
Out of box installation

from

$1.79

Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.

Product Features:

Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
Quality material – this retainer is made of durable material for long-lasting service
Versatile design – this retainer is suitable for a variety of automotive uses
Excellent value – this part offers original equipment quality at a competitive cost

from

$14.29

Carquest Premium Thermostats are manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. With the enlarged Orpheus opening, this high flowing thermostat will allow for more gallons per second to flow. This will allow for the engine to cool down at a faster rate compared to the OE to allow for quick and precise cooling for your engine. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features: