2013 GMC Sierra 3500 HD Towing Products

The stylish and innovative design of these steps add to a vehicle rugged off-road look. Available in three low maintenance, extremely durable finishes to complement your vehicle appearance. Easily installed using our new multi mount system for superior strength and rigidity. Rocker panel installation provides for the strongest and easiest installation of any step products.

Product Features:

• Exclusive New Multi Mount System
• Made Of Corrosion Resistant, Durable Cast Aluminum Alloy
• Rugged Tread Pattern Provides For Safe And Attractive Non Slip Surface
• Unique Design Gives The Vehicle A Rugged Off-Road Look, While Being A Stylish Accent For Today Vehicles
• Strong Construction To Hold Up Under Extreme Conditions
• Mechanical Polished Finish That Will Not Rust, Crack Or Peel And Requires Very Little Maintenance
• Strongest And Easy Installation

Reduce your installation time to minutes! Many of today’s tow vehicles come with an O.E.M. connector or harness wires under the dash. The 47685 simply splices onto the tow vehicle tow package supplied wires and then plugs into the Hopkins brake control to complete the install.

Product Features:

• Blunt cut wires allows for installation of any brake control
• 36 inch wire length
• For vehicles with a factory tow package
• Includes Step-By-Step Instructions And Diagrams

When the original trailer brake control module circuit board fails on certain General Motors trucks, you usually have to replace the entire module. This Dorman OE FIX circuit board allows direct replacement of only the failed board, saving money.

Product Features:

• Trailer Brake Control Switch – Circuit Board
• Trailer Brake Control Switch – Circuit Board
• When the original trailer brake control module circuit board fails on certain General Motors trucks, you usually have to replace the entire module. This Dorman OE FIX circuit board allows direct replacement of only the failed board, saving money.
• Simplified replacement – this trailer brake control switch circuit board directly replaces a burnt out module circuit board
• Saves money – this unique solution reduces repair cost by eliminating need to replace entire module

A CURT front trailer hitch allows you to use the front end of your vehicle for a variety of towing applications. They can be used for mounting a winch, a snow plow, a number of towing accessories and can even be used for some trailering applications. When space is limited, a front trailer hitch is commonly used to hold a cargo carrier, freeing up space inside the vehicle for extra cargo and making the rear mount receiver available to pull a trailer. At the boat ramp, your boat trailer can be hitched up to the front receiver hitch, giving you better control over the trailer as you launch. Some of the other accessories that can be used with a front tow hitch are the CURT winch mount, step pad, license plate holder, spare tire mount, skid shield and tow hooks. All CURT front trailer hitches provide a useful receiver tube to accept a 2″ x 2″ shank, and they are commonly used on trucks, vans and SUVs. This front trailer hitch is rated for 5,000 lbs. GTW and 500 lbs. TW. It also has a straight-line pull rating of 9,000 lbs. It is designed to be a custom trailer hitch for certain years of the Chevy Silverado 2500 HD or 3500 HD and GMC Sierra 2500 HD or 3500 HD (to verify your vehicle compatibility, see application info). It comes with all necessary hardware for a complete installation and is backed by a limited lifetime warranty.

Product Features:

• Rated to 5,000 lbs. gross trailer weight and 500 lbs. tongue weight
• Compatible with a tow hook or shackle mount (9,000 lbs. straight-line pull)
• Engineered with a vehicle-specific design for a custom fit
• Provides a convenient mount for hitch accessories
• Ideal for attaching a snow plow, cargo carrier or other front hitch mount
• Allows for easy maneuvering of a trailer into a tight spot
• Concealed main body for OE look and seamless integration with the vehicle
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Protected by a durable black powder coat finish
• Co-cured in a rust-resistant liquid Bonderite coating
• Equipped with an open-back receiver for easy cleaning
• Made in USA

Whatever your task at hand — whether it’s launching that boat before daybreak, setting up your camper before the rush or getting a final load to the dump before close — CURT class 3 trailer hitches offer the strength needed for serious towing. They make it easy to hitch up and Bring It, offering a vehicle-specific fit and the weight capacity to handle a variety of trailers. Custom class 3 hitches are the most common type of receiver hitch for pickup trucks and SUVs. Because of their weight range, they are also found on full-size cars, crossovers and minivans. Each custom-fit class 3 hitch package is made for vehicle-specific mounting. This particular kit fits certain years of the Chevy Silverado 2500 HD or 3500 HD and GMC Sierra 2500 HD or 3500 HD (see application info to verify vehicle compatibility). It provides a weight carrying capacity of 8,000 lbs. GTW and 800 lbs. TW. It is also compatible with a weight distribution hitch for level towing and a rating of 12,000 lbs. WD and 1,200 lbs. WDTW. CURT class 3 trailer hitches are typically used to attach and haul utility trailers, boat trailers, campers, snowmobile or ATV haulers and more (NOTE: Never exceed the lowest-rated towing component). Each class 3 hitch has a 2″ receiver tube and is tested in accordance with SAE J684 for safety. To ensure that CURT class 3 receiver hitches have what it takes for serious trailering, they are designed using a hands-on approach and are constructed with rugged, high-strength steel and precise welding. We also protect our class 3 hitches in a co-cured finish of liquid A-coat and black powder coat for superior resistance to rust, chipping and UV damage.

Product Features:

• Rated to 8,000 lbs. gross trailer weight and 800 lbs. tongue weight
• Compatible with weight distribution hitch (12,000 lbs. WD / 1,200 lbs. WDTW)
• Engineered with a vehicle-specific design for a custom fit
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid A-coat, inside and out
• Equipped with an open-back receiver for easy cleaning
• Made in USA (may include imported hardware)

Easily route towing electrical functions into the truck bed for 5th wheel and gooseneck trailers, while retaining electrical functions at the rear bumper of the vehicle. This harness allows you to directly plug into the factory USCAR connector under the truck and has terminated wires at the other end so you can hardwire different styles of plugs for use inside the truck bed.

Product Features:

• Easily Route Towing Electrical Functions Into The Truck Bed For Fifth Wheel Trailers
• Reinforced 90 degree angle
• Plugs into OEM wiring system
• Easy to install

A CURT custom wiring connector (sometimes called a T-connector) is a simple, plug-and-play electrical device that eliminates the need for cutting, splicing and soldering when installing vehicle-to-trailer wiring. Most vehicles do not come ready to tow. Unless your vehicle has a towing package, it is probably not equipped with a trailer wiring connector. This is where CURT’s custom wiring connectors come into play. A custom wiring connector uses a single original equipment plug to plug into a special socket provided by your vehicle. Though this option is not available on every vehicle, some automotive manufacturers design their vehicles to be easily equipped for towing by supplying a socket, integrated into the vehicle’s electrical system, to readily accept a custom wiring connector. With a CURT custom wiring connector, there is no need to tap into the taillight assembly because a special socket is already provided. This special custom wiring connector actually provides two connector sockets for a multipurpose option. It plugs into an OEM USCAR connector and offers a 4-way flat and 6-way round connector (see application info to verify fitment with your vehicle). It also comes with a mounting bracket for easy installation. CURT custom wiring connectors are designed to be long-lasting and simple to install. They come with dust covers to keep your connector clean when not in use.

Product Features:

• Plugs into USCAR socket to provide 4-way and 6-way trailer wiring connectors
• Fits USCAR-equipped vehicles with factory tow plugs only
• Simple plug-and-play design eliminates the need for cutting or splicing
• 4-way flat output connects tail lights, brake lights and turn signals
• 6-way round socket adds connection for electric brakes and auxiliary power
• Dust covers included to keep connectors clean when not in use
• Slit loom keeps wires contained and well protected
• Metal bracket securely mounts wiring to the vehicle or trailer hitch

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

GM Genuine Parts Trailer Tow Relays are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These relays function as an electro-mechanical switch containing a coil and set of connection points. These trailer tow relays provide a variety of control functions for a vehicle’s trailer brake system. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

Add light mounts to your Dee Zee Aluminum or Steel Headache Rack or Rear Rack. With these convenient mounts that slide into the built in channel system, mounting your auxiliary lights is quick and easy. Several size options to meet your needs.

Product Features:

• Made From Rugged Steel
• Protective Gloss Black Powder Coat Finish
• Utilize The Accessory Channel On Aluminum Cab Racks
• Several Size Options To Meet Your Needs
• Made In USA

One Key Technology Allows You To Use Your Ignition Key Eliminating Need For Extra Keys.

One Key Technology Allows You To Use Your Ignition Key Eliminating Need For Extra Keys.

A CURT Quick Plug brake controller wiring adapter is one of the fastest and easiest ways to plug your brake controller into your vehicle. It requires no cutting or splicing! Just insert the vehicle-specific plug end into the OEM vehicle’s factory brake controller socket. The other end plugs into your CURT trailer brake controller. Quick Plug harnesses are available for a variety of vehicles and are unique for each vehicle application to provide the easiest possible installation. This particular brake controller harness fits certain years of the Cadillac Escalade, Escalade ESV, Chevy Silverado and GMC Sierra 1500, 1500 LD, 1500 Limited, 2500HD, 3500HD Suburban, Suburban 1500, Suburban 3500HD, Tahoe, Yukon and Yukon XL (see application info to verify fitment). CURT Quick Plug harnesses are compatible with most CURT brake controls and can be used as a replacement or for a new control unit installation. They’re also great for towing all types of trailers with electric brakes. For versatile mounting of your trailer brake controller this Quick Plug wire harness measures two feet long. It also features a slit loom sleeve to keep the wires protected against crushing and abrasions. CURT Quick Plug wire plug-in adapters are made with 12-gauge wires for a reliable connection and braking, and come with zip ties to keep the harness contained and out of sight.

Product Features:

• Allows a CURT trailer brake controller to be plugged into OEM socket
• Quick plug harness installs with plug-and-play convenience
• Wire colors match standard brake controller harnesses
• Includes 24″ of 12 gauge wire for flexible installation
• Slit-loom sleeve keeps wires contained and protected

Like trailer hitches and ball mounts, electrical connectors range all over the board in shape, size and capability, but no matter what your trailer’s electrical functions are, you need a solid connection to keep the power flowing and ensure safety on the road. CURT electrical connectors are designed and manufactured to give you a reliable connection every time you plug in your trailer. This 7-way RV blade connector is designed to plug into a USCAR socket and supply power for tail lights, turn signals, electric trailer brakes, a 12-volt battery, reverse lights and brake lights, as well as a ground connection. It is intended to be a replacement trailer connector, plugging into a standard USCAR socket (see application info to verify fitment with your vehicle). It features rust-free black plastic construction and comes with a spring-loaded cover to keep out dust and water. This 7-way RV blade connector is a female-end socket, specifically designed for the vehicle side of the connection.

Product Features:

• Plugs into USCAR socket to provide 7-way RV blade trailer wiring connector
• Simple plug-and-play design eliminates the need for cutting or splicing
• 7-way connects tail, brake, reverse, turn signals, brakes and auxiliary power
• Spring-loaded dust cover keeps connector clean when not in use

New trucks are becoming more car-like every year making it almost impossible to install a traditional brake controller. With the InSIGHT brake control, you gain the flexibility needed to make a simple, no tools required installation in any vehicle. This three part system allows the driver to bring the display back in sight where they can see what is going on as well as bringing the controls within a comfortable reach whether you are right or left handed. Mount the brain of the system out of sight. So, no more banging your knee every time you get in and out of your vehicle. This proportional brake controller creates stops that are safe and smooth, making you feel like you aren’t even towing a trailer! With easy to set gain adjustments and a digital display will make setting this brake control quick and easy. Seven On-the-fly sensitivity settings allows you to adjust for trailer weights and weather at the press of a button. Most states and provinces require a trailer brake controller based on the weight of the trailer.

Product Features:

• Proportional braking
• No Tools Required Installation, no drilling required
• Percentage of braking power shown
• 7 Sensitivity Settings for Advanced Braking Control
• Intuitive vertical manual slide
• Short Proof Protected
• Controls up to 8 trailer brakes

GM Genuine Parts Trailer Brake Controls are designed, engineered, and tested to rigorous standards, and are backed by General Motors. the brake controls signal a trailer’s brake system when the driver presses on the brake pedal and adjusts how much braking power is needed to stop the trailer. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

They’ve made the truck said to turn the world under its tires and the trailer that moves mountains in a day. But what about the hitch powerful enough to connect the two? The CURT under-bed Double Lock EZr gooseneck hitch features a gross trailer weight capacity up to 30,000 lbs., a vertical load limit of 7,500 lbs. and easier, more secure towing for your gooseneck trailer. Providing a solid foundation for the Double Lock EZr, this set of gooseneck installation brackets is designed for a vehicle-specific fit to maximize your pickup’s towing potential and integrate with the frame seamlessly. Installation with the CURT Double Lock EZr is fast and easy. Because the installation brackets are made vehicle-specific, they use pre-existing holes in the vehicle’s frame and require less drilling. The Double Lock EZr requires only one person during installation, using retainer clips to keep bolts secure and the center section fully supported while mounting it into place. It also uses carriage bolts whenever possible for one-wrench tightening and does not require the exhaust to be lowered during installation. This particular set of gooseneck installation brackets is specifically designed to mount the CURT Double Lock EZr gooseneck hitch #60619 on certain years of the Chevy Silverado and GMC Sierra 2500HD or 3500 (see application info to verify fitment). It features a laser-cut construction for a precise fit and is rated to the vehicle’s maximum gross trailer weight capacity. With each gooseneck installation bracket sub kit, we provide the necessary hardware for an easier installation, and we coat our gooseneck brackets in a liquid A-coat to make sure rust and other potential threats are not a problem.

Product Features:

• Mounts the Double Lock EZr gooseneck hitch on specific pickup truck models
• Vehicle-specific design optimizes strength and installation time
• Constructed from high-strength, laser-cut steel for a precise fit
• Protected by a rust-resistant liquid A-coat
• Includes grade-8 mounting hardware

A CURT gooseneck hitch is more than a necessary tool for towing; it is an integrated extension of your truck that allows you turn your 4×4 into the workhorse it was designed to be. Gooseneck hitches are stronger, tougher and more subtle than any other, and when quality craftsmanship and intelligent design become the fuel that drives a gooseneck hitch, you get a towing solution that leaves others lost for words. The CURT under-bed Double Lock gooseneck hitch is strong, fast and easy to operate. It gets its name from the two locking pins that engage the trailer ball and hold it in place, giving you twice the security when towing especially heavy trailers. The Double Lock mounts underneath your truck bed with compatible gooseneck installation brackets and provides a removable 2-5/16″ gooseneck trailer ball with a gross trailer weight capacity up to 30,000 lbs. and a tongue weight capacity of 7,500 lbs. Using the heavy-duty operating handle, the trailer ball can be unlocked and flipped over whenever necessary to allow full use of the truck bed. The Double Lock comes with solid safety chain hookups, an attractive chrome trim ring, a durable A-coat finish and a limited lifetime warranty. This particular Double Lock gooseneck hitch is design to fit several models of Chevrolet, GMC, Dodge, Ram, Ford and Toyota (for a complete listing of vehicle and installation bracket compatibility, see application info).

Product Features:

• Double locking pins for superior trailer and trailer ball security
• Flip-and-store ball keeps truck bed free of obstructions
• Removable chrome-plated 2-5/16″ trailer ball fits most gooseneck trailers
• Installation requires no welding or truck bed removal
• Heavy-duty handle can be positioned on either side of the vehicle
• Chrome-plated trim ring provides a finished look
• Rubber hole cover helps prevent corrosion in trailer ball hole
• Includes spring-loaded safety chain loops and grade-8 hardware
• Protected by a durable A-coat finish

Whatever your task at hand — whether it’s launching that boat before daybreak, setting up your camper before the rush or getting a final load to the dump before close — CURT class 3 trailer hitches offer the strength needed for serious towing. They make it easy to hitch up and Bring It, offering a vehicle-specific fit and the weight capacity to handle a variety of trailers. Custom class 3 hitches are the most common type of receiver hitch for pickup trucks and SUVs. Because of their weight range, they are also found on full-size cars, crossovers and minivans. Each custom-fit class 3 hitch package is made for vehicle-specific mounting. This particular kit fits certain years of the Chevy Silverado 2500 HD, 2500 HD Classic, 3500, 3500 HD or 3500 Classic and GMC Sierra 2500 HD, 2500 HD Classic, 3500, 3500 HD or 3500 Classic (see application info to verify vehicle compatibility). It provides a weight carrying capacity of 6,000 lbs. GTW and 600 lbs. TW. It is also compatible with a weight distribution hitch for level towing and a rating of 10,000 lbs. WD and 1,000 lbs. WDTW. CURT class 3 trailer hitches are typically used to attach and haul utility trailers, boat trailers, campers, snowmobile or ATV haulers and more (NOTE: Never exceed the lowest-rated towing component). Each class 3 hitch has a 2″ receiver tube and is tested in accordance with SAE J684 for safety. To ensure that CURT class 3 receiver hitches have what it takes for serious trailering, they are designed using a hands-on approach and are constructed with rugged, high-strength steel and precise welding. We also protect our class 3 hitches in a co-cured finish of liquid A-coat and black powder coat for superior resistance to rust, chipping and UV damage.

Product Features:

• Rated to 6,000 lbs. gross trailer weight and 600 lbs. tongue weight
• Compatible with weight distribution hitch (10,000 lbs. WD / 1,000 lbs. WDTW)
• Engineered with a vehicle-specific design for a custom fit
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid A-coat, inside and out
• Equipped with an open-back receiver for easy cleaning
• Made in USA (may include imported hardware)

Whatever the next item is on your to-do list — whether it’s arriving at the jobsite before dawn or getting your travel trailer set up in time to see the sunset — CURT class 4 trailer hitches offer greater towing power to let you Bring It. These custom receiver hitches are built to tackle bigger jobs and bolder adventures, all while giving you a custom fit for your vehicle. Class 4 hitches are available for a variety of makes and models, from pickup trucks and SUVs to full-size and commercial vans. This particular class 4 hitch fits certain years of the Chevy Silverado 2500 HD or 3500 HD and GMC Sierra 2500 HD or 3500 HD (to verify vehicle compatibility, see application info). It provides a weight carrying capacity of 10,000 lbs. GTW and 1,000 lbs. TW. It can also accept a weight distributing hitch, offering a maximum WD capacity of 12,000 lbs. and a WDTW of 1,200 lbs. CURT class 4 tow hitches are as much suited for work as they are for play. With their high load capacities, they are typically used for towing larger trailers, including everything from a double-axle utility trailer or livestock trailer to a full-length camper or large boat trailer (NOTE: Never exceed the lowest weight capacity of any towing component). All CURT class 4 receiver hitches come with a 2″ receiver tube opening and all the necessary hardware for a complete installation. From light-duty to heavy-duty, every CURT custom hitch is engineered to be vehicle-specific, using actual vehicles to create the optimal design. We then combine high-strength steel, precise welding and a co-cured finish of liquid A-coat and durable black powder coat to provide you with a hitch you can depend on. To prove it, we test all our hitches in accordance with SAE J684 for safety.

Product Features:

• Rated to 10,000 lbs. gross trailer weight and 1,000 lbs. tongue weight
• Compatible with weight distribution hitch (12,000 lbs. WD / 1,200 lbs. WDTW)
• Engineered with a vehicle-specific design for a custom fit
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid A-coat, inside and out
• Equipped with an open-back receiver for easy cleaning
• Made in USA (may include imported hardware)

It does not matter what you haul, you need to make sure to secure it properly in order to protect your truck, yourself and other motorists. Dee Zee Cab Rack Tie Downs offer a reliable method for securing your cargo to your cab rack. Designed to fit into your cab rack integrated channel, our Tie Downs glide along your rack accessory channel tightening into place for virtually endless possibilities.

Product Features:

• Tie Down Anchor For Cargo
• Cast Aluminum Finish
• Fits Into Integrated Channel In Cab Rack
• No Drilling Required

Outfitting your pickup to tow a heavy-duty flatbed or livestock trailer is easy with CURT OEM puck system gooseneck safety chain anchors. Like our OEM puck system gooseneck balls, these safety chain anchors utilize the puck system built into certain pickup trucks today with the towing prep package. They feature a patented installation system, easily dropping into the truck bed pucks without any tools required. They feature heavy-duty forged steel construction with a durable carbide black powder coat finish, and they offer large safety chain loops to accept heavy-duty hooks. These particular OEM puck system gooseneck safety chain anchors are compatible with the puck system of select model years of the Chevrolet Silverado 2500 HD and 3500 HD, Ford F-250 and F-350 Super Duty, GMC Sierra 2500 HD and 3500 HD and Nissan Titan XD (see application info to verify fitment). The anchors can be purchased as a standalone item or as part of a complete kit (#60692) that also includes the OEM puck system gooseneck ball, a rubber hole cover and a durable storage case.

Product Features:

• Fits select Chevrolet, Ford, GMC and Nissan Titan XD puck systems
• Simple, drop-in installation eliminates the need for tools
• Wide loop openings accept large gooseneck safety chain hooks
• Forged steel anchors with durable carbide black powder coat finish

Snap and Zap Towing Mirrors. K Source is a unique manufacturer in that we specialize in making only automotive and motorcycle mirrors. Our experience in this category for over 71 years is exactly what our customers have come to trust and rely upon, as our manufacturing and marketing expertise has consistently led the market in replacement products.

Product Features:

• Easy Clip-on Install – no tools or additional hardware required
• Molded to fit Factory Mirrors
• Extension does not interfere with OE Mirror Glass
• Mirrors can be folded Without removing extensions
• Includes both Driver and Passenger Side Mirror Extensions

Snap and Zap Towing Mirrors. K Source is a unique manufacturer in that we specialize in making only automotive and motorcycle mirrors. Our experience in this category for over 71 years is exactly what our customers have come to trust and rely upon, as our manufacturing and marketing expertise has consistently led the market in replacement products.

Product Features:

• Easy Clip-on Install – no tools or additional hardware required
• Molded to fit Factory Mirrors
• Extension does not interfere with OE Mirror Glass
• Mirrors can be folded Without removing extensions
• Includes both Driver and Passenger Side Mirror Extensions

Snap and Zap Towing Mirrors. K Source is a unique manufacturer in that we specialize in making only automotive and motorcycle mirrors. Our experience in this category for over 71 years is exactly what our customers have come to trust and rely upon, as our manufacturing and marketing expertise has consistently led the market in replacement products.

Product Features:

• Easy Clip-on Install – no tools or additional hardware required
• Molded to fit Factory Mirrors
• Extension does not interfere with OE Mirror Glass
• Mirrors can be folded Without removing extensions
• Includes both Driver and Passenger Side Mirror Extensions

In the world of commercial towing, more is expected. A job cannot be completed if the equipment cannot handle the workload. That is why CURT developed the Commercial Duty class 5 trailer hitch. Constructed from steel and engineered for power, these class 5 hitches are designed to complement the towing power of full-size, commercial pickup trucks, including diesels and chassis cabs. They can easily handle a variety of oversize trailers, including toy and car haulers, livestock trailers, dumper trailers, large flatbed trailers, large boat trailers and more (NOTE: Never exceed the lowest weight capacity of any towing component). This particular class 5 hitch features a gross trailer weight capacity of 20,000 lbs. and a tongue weight capacity of 2,700 lbs. It is designed to be a custom trailer hitch for certain years of the Chevy Silverado 3500, 3500 HD or 3500 Classic, Dodge Ram 3500, 4500 or 5500, GMC Sierra 3500, 3500 HD or 3500 Classic and Ram 3500, 4500 or 5500 (to verify your vehicle compatibility, see application info). All CURT Commercial Duty class 5 hitches feature a 2-1/2″ x 2-1/2″ receiver tube opening to accept the strongest of ball mounts and towing accessories. They are perfect for mounting standard ball mounts, pintle mounts, tow hooks and weight distribution hitches as well as winch mounts and cargo carriers. CURT class 5 tow hitches are protected by a co-curing of liquid A-coat and carbide black powder coat finish. They also mount with grade-8 hardware, included with each hitch.

Product Features:

• Rated to 20,000 lbs. gross trailer weight and 2,700 lbs. tongue weight
• Compatible with weight distribution hitch (20,000 lbs. WD / 2,700 lbs. WDTW)
• Engineered with a vehicle-specific design for a custom fit
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Constructed with a large, powerful main body
• Protected by a highly durable carbide powder coat finish
• Co-cured in a rust-resistant liquid A-coat, inside and out
• Features wide safety chain openings for heavy-duty hooks
• Equipped with an open-back receiver for easy cleaning
• Made in USA (may include imported hardware)

Whatever your task at hand — whether it’s launching that boat before daybreak, setting up your camper before the rush or getting a final load to the dump before close — CURT class 3 trailer hitches offer the strength needed for serious towing. They make it easy to hitch up and Bring It, offering a vehicle-specific fit and the weight capacity to handle a variety of trailers. Custom class 3 hitches are the most common type of receiver hitch for pickup trucks and SUVs. Because of their weight range, they are also found on full-size cars, crossovers and minivans. Each custom-fit class 3 hitch package is made for vehicle-specific mounting. This particular kit fits certain years of the Chevy Silverado 2500 HD or 3500 HD and GMC Sierra 2500 HD or 3500 HD (see application info to verify vehicle compatibility). It provides a weight carrying capacity of 8,000 lbs. GTW and 800 lbs. TW. It is also compatible with a weight distribution hitch for level towing and a rating of 12,000 lbs. WD and 1,200 lbs. WDTW. CURT class 3 trailer hitches are typically used to attach and haul utility trailers, boat trailers, campers, snowmobile or ATV haulers and more (NOTE: Never exceed the lowest-rated towing component). Each class 3 hitch has a 2″ receiver tube and is tested in accordance with SAE J684 for safety. To ensure that CURT class 3 receiver hitches have what it takes for serious trailering, they are designed using a hands-on approach and are constructed with rugged, high-strength steel and precise welding. We also protect our class 3 hitches in a co-cured finish of liquid A-coat and black powder coat for superior resistance to rust, chipping and UV damage.

Product Features:

• Rated to 8,000 lbs. gross trailer weight and 800 lbs. tongue weight
• Compatible with weight distribution hitch (12,000 lbs. WD / 1,200 lbs. WDTW)
• Engineered with a vehicle-specific design for a custom fit
• Concealed main body for OE look and seamless integration with the vehicle
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid A-coat, inside and out
• Equipped with an open-back receiver for easy cleaning
• Made in USA (may include imported hardware)