from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$9.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$15.99

Toyota Landcruiser pinion nut, coarse spline, LARGE. 22mm x 1.5mm.

Product Features:

Pinion nut
Fits Toyota Landcruiser with 10 spline pinion

from

$353.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Toyota 8″ clamshell front
Reverse rotation only
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$135.99

Product Features:

Conversion kit
Fits Toyota V6 rear with 29 spline pinion
Includes yoke , pinion seal, and pinion nut

from

$295.99

Product Features:

TOY 10BL 7.8 R/P 4.11 V6 MG

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$13.49

Product Features:

KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

from

$118.44

Differential Pinion

from

$208.99

8″ standard Open case, bare.

Product Features:

Standard open carrier case
Fits Toyota 8″ with 4 cylinder engine

from

$51.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Toyota 8″ and 4 cylinder engine, 1986 and up with OEM ring and pinion set
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$37.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$6.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$131.02

Differential Bearing

from

$8.40

Axle Seal

from

$11.78

Pinion Seal

from

$315.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$259.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$109.99

Bearing race driver for Toyota 7.5″, 8″ rear. (TOY32307). No return.

Product Features:

Bearing race driver
Fits 32307 race
All steel construction

from

$188.99

Bearing race driver for rear Toyota V6, Landcruiser reverse rotation, and Tacoma with locker. (TOY35028). No return.

Product Features:

Bearing race driver
Fits 35028 race
All steel construction

from

$7.99

DiffRingGearBolt

from

$15.99

Ring Gear bolt for Toyota T100, Tacoma & 8″ IFS front. 12mm x 1.0.

Product Features:

Ring gear bolt for Toyota T100 and Tacoma rear without factory locking differential and Toyota Clamshell front
12mm x 1.0

from

$10.99

Toyota clamshell design crush sleeve. Approx 1.475″ long.

Product Features:

Crush sleeve
Fits Toyota 8″ clamshell front
1.475″ tall

from

$51.99

Differential Crush S

from

$341.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits standard rotation Toyota 7.5″ front with 4 cylinder engine
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$502.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses high quality bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. This kit fits applications with a 27 spline pinion.

Product Features: