2012 GMC Canyon Automatic Transmission Parts

AUTO TRANS BAND

This transmission control module has been fully tested and validated to match the function and performance of the original TCM on specified vehicle applications.

Product Features:

• Direct replacement – this transmission control module matches the function and performance of the stock TCM on specified years, makes and models
• Ideal solution – this transmission control module is a reliable replacement for an original part that has failed due to corrosion or electrical failure
• Thoroughly tested – this TCM has undergone full vehicle simulator testing to confirm full functionality for reliable performance
• Requires programming – after installation, module must be programmed with original manufacturer software, such as through a Remote Assist Programming (RAP) Kit

GM Genuine Parts Transmission Control Modules are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These modules help control shifting in vehicles with automatic transmissions. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
• Dictates the operation of your vehicle’s vital systems, which is critical to the performance of your vehicle
• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

GM Genuine Parts Transmission Control Modules are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These modules help control shifting in vehicles with automatic transmissions. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
• Dictates the operation of your vehicle’s vital systems, which is critical to the performance of your vehicle
• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

ATHARNESS VSS REPR

AT/HARNESS VSS REPR

ATP Automatic Transmission Control Solenoid (Lock-Up)

AT CONTR SOLENOID

AT CONTR SOLENOID

Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• Quick Link Splice Connectors

B&M transmission bracket for General Motors 4L60E, 4L65E, 4L80E and 4L85E automatic transmissions with a PRNDL style switch.

Product Features:

• Shifter Service Parts

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required. All of friction components are replaced with upgraded heavy duty parts. Drum assemblies are air checked and side play is checked to assure proper clearance. All of seals, o’rings and gaskets are replaced. All of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing. Transmissions are assembled, end plays are set and fasteners are torqued to the required specification. All of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno test. Transmission park locking mechanism is checked during dyno test. (where applicable). (Torque Converter) All of converters are dynamic balanced. All of pumps are furnaced brazed. All new bearings and o’rings. All new springs and rollers in stator. All new thrust washers. All new friction liners in overdrive lockup converters. Converter endplay and hub/pump runout and diameter is checked.

Product Features:

• All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
• 100% of friction components are replaced with upgraded heavy duty parts.
• Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
• 100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
• Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
• Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
• 100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
• Product might not be available in all states due to local laws.

At Shift Pro Inc, fully remanufactured transmissions go beyond the name. So, what’s in that name to start? Pro Engineering: your transmission has been re-engineered to meet or exceed OE standards for tolerances, durability, and quality. Pro Performance: upgraded components and a fully remanufactured torque converter add to enhanced durability over your transmission’s lifetime. Pro Performance: hot-, cold-, load-, and simulated road-tested on custom dynamometers, your transmission is ready to go, wherever you’re headed.

Product Features:

• Fully tested torque converter included. Shift Pro Inc tests for leaks, lock-up, concentricity, and balance to eliminate the possibilities of front seal leaks, premature bushing wear, and vibration.
• All dynamometer testing is conducted with Shift Pro Inc’s custom testing program for at least 30 minutes.
• During dynamometer testing, Shift Pro Inc transmissions are cold, hot, load, and road tested using a fully synthetic transmission fluid and filtration system.
• All wear-prone valves in the completely remanufactured valve body are restored to stringent specifications and vacuum tested to verify proper function.
• Shift Pro Inc’s quality control process includes build specification checks performed by four different specialized technicians during the remanufacturing process.
• No paperwork or registration is required with Shift Pro Inc’s warranty. Each no-hassle warranty is attached to the vehicle VIN and transferrable with ownership.
• Product might not be available in all states due to local laws.

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required. All of friction components are replaced with upgraded heavy duty parts. Drum assemblies are air checked and side play is checked to assure proper clearance. All of seals, o’rings and gaskets are replaced. All of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing. Transmissions are assembled, end plays are set and fasteners are torqued to the required specification. All of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno test. Transmission park locking mechanism is checked during dyno test. (where applicable). (Torque Converter) All of converters are dynamic balanced. All of pumps are furnaced brazed. All new bearings and o’rings. All new springs and rollers in stator. All new thrust washers. All new friction liners in overdrive lockup converters. Converter endplay and hub/pump runout and diameter is checked.

Product Features:

• All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
• 100% of friction components are replaced with upgraded heavy duty parts.
• Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
• 100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
• Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
• Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
• 100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
• Product might not be available in all states due to local laws.

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required. All of friction components are replaced with upgraded heavy duty parts. Drum assemblies are air checked and side play is checked to assure proper clearance. All of seals, o’rings and gaskets are replaced. All of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing. Transmissions are assembled, end plays are set and fasteners are torqued to the required specification. All of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno test. Transmission park locking mechanism is checked during dyno test. (where applicable). [Torque Converter] All of converters are dynamic balanced All of pumps are furnaced brazed. All new bearings and o’rings. All new springs and rollers in stator. All new thrust washers. All new friction liners in overdrive lockup converters. Converter endplay and hub/pump runout and diameter is checked

Product Features:

• All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
• 100% of friction components are replaced with upgraded heavy duty parts.
• Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
• 100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
• Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
• Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
• 100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

This shift interlock solenoid is designed to match the fit and function of the original solenoid on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this shift interlock solenoid is designed to match the fit and function of the original solenoid on specified vehicles
• Ideal solution – this solenoid is a reliable replacement for an original part that is damaged or has failed due to fatigue, excessive heat or electrical current
• Durable construction – this solenoid is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

This shift interlock solenoid is designed to match the fit and function of the original solenoid on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this shift interlock solenoid is designed to match the fit and function of the original solenoid on specified vehicles
• Ideal solution – this solenoid is a reliable replacement for an original part that is damaged or has failed due to fatigue, excessive heat or electrical current
• Durable construction – this solenoid is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

This automatic transmission shifter cable lever is designed to match the fit and function of the original lever on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this automatic transmission shifter cable lever is designed to match the fit and function of the original lever
• Restores functionality – reliable replacement for an original part that has failed due to corrosion
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Shift Solenoid