2012 Ford F-150 Performance Engines

Competition Cams Xfi Nsr Blower 228/235 Hydraulic Roller Cams For Ford 5.0L Coyote, 191360.

Competition Cams Xfi Nsr 228/231 Hydraulic Roller Cams For Ford 5.0L Coyote, 191100.

“Edelbrock part No: 5022 Torker-Plus Camshaft is designed for small-block Ford 289-302 V-8 applications. The camshaft works well with Torker II manifolds for performance from 2500 to 6500 rpm, this camshaft is ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft. Camshaft Specifications: – Duration at .050 Intake: 214 degrees – Duration at .050 Exhaust: 224 degrees – Lift at Valve Intake: .472″” – Lift at Valve Exhaust: .496″” – Lobe Separation: 112 Degrees – Intake Centerline: 107 Degrees”

HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

“Edelbrock part No: 7122 Performer RPM Camshaft is designed for small-block Ford 289-302 V-8 applications. This Edelbrock cam kit produced 367 HP & 340 ft-lbs. of torque when used with No: 7121 intake and No: 60259 cylinder heads on a 302 engine. The camshaft works well with high-performance’s street applications, Performer RPM cams provide power from 1500 to 6500 rpm. This hydraulic lifter camshaft is dyno-matched to Performer RPM manifolds for high-rpm horsepower while still maintaining acceptable low-end torque. With 10 to 12 inches of manifold vacuum at idle, Performer RPM cams have more lift and duration than most street camshafts. Hydraulic flat tappet lifters are included with each Performer RPM camshaft. Camshaft Specifications: – Duration at .050 Intake: 224 degrees – Duration at .050 Exhaust: 234 degrees – Lift at Valve Intake: .496″” – Lift at Valve Exhaust: .520″” – Lobe Separation: 112 Degrees – Intake Centerline: 107 Degrees – Idle Vacuum at 1000 RPM’s: 11″””

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

The POWERAID Throttle Body Spacer is designed to enhance off-idle torque from 800 rpm to approximately 3,000 rpm. The spacer utilizes it’s unique, patented Helix Bore design to spin the incoming air charge as it passes through the throttle body spacer. The spinning air action boosts the velocity of the incoming air And contributes to better atomization of the air/fuel mixture as the air charge enters the combustion chamber. The end result is more part-throttle torque And improved mid-range power.

Weiand High-Rise Dual Plane Intake Manifold for Maximum Torque, 8012.

Edelbrock Performer 351 Intake Manifold for Ford 351- 4V Cleveland, 2665.

The Holley Sniper EFI is a high-performance sheet metal fabricated intake manifold designed for GM LS7 engines. Built from durable T6061 aluminum with a 102mm throttle body opening, it delivers improved airflow, throttle response, and under-hood styling-perfect for racers and performance enthusiasts.

Race winning design for all types of competition. Single plane maximizes torque and horsepower. Runners feature extra material for custom porting. For performance in 3500 to 7500 RPM range. Fits SVO blocks with 9.20 inch deck height. Ideal for both oval track and drag racing engines. Runners have 2.70 square inch cross sectional area. Match with Edelbrock heads for maximum performance.

Edelbrock part #5021 Torker II 302 intake manifold is designed for street 289-302 c.i.d. Ford V8’s. Will not fit Boss 302. Manifold not equipped with EGR. Will not fit 255 c.i.d. Ford V8 engines. Not for heavy vehicles. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com.

Holley EFI KIT FORD 351W HI-RAM 95MM EFI BLACK, 300-241BK.

Holley EFI MFLD KIT FORD 351W HI-RAM 95MM EFI, 300-241.

Edelbrock Performer 351 Intake Manifold for Ford 351- 2V Cleveland Engine, 2750.

Edelbrock Performer 289 Intake Manifold for Small-Block Ford, Polished Finish, 21211.

Edelbrock Performer 351-W Intake Manifold for S/B Ford 351 Windsor, 2181.

Edelbrock part #7581 RPM Air-Gap 351W intake manifold is designed for street and high performance 351-427 c.i.d. 351W Ford V8 applications. The RPM Air-Gap incorporates the same race-winning design that’s been used on our Victor Series competition intakes for decades. The Air-Gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power. Larger cross sectional area and a taller carb flange than #7181 for compatibility with large displacement, stroker 351W based engines. Includes bosses for nitrous and rear water crossover. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com.

“Edelbrock part #5081 Torker II 351W intake manifold is designed for 1969 and later 351 Windsor Ford V8 high-performance engines with Edelbrock heads, OEM 12- or 16-bolt heads or equivalent. Will not fit “”Boss 351″” Cleveland. Manifold not equipped with EGR. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com.”

Edelbrock RPM Air-Gap Small Block Ford 302 Black Intake Manifold, 75213.

Edelbrock part #2121 Performer 289 intake manifold is designed for street 260-289-302 c.i.d. Ford V8’s without EGR. Will not fit Boss 302 or 255 c.i.d. V8’s. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response from off-idle through 5500rpm. The Performer intake manifolds are ideal for passenger cars, trucks, 4x4s, tow vehicles and RVs. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to www.lokar.com.