2012 BMW 128i Cooling and Climate Controls

Essential 2012 BMW 128i Cooling and Climate Controls

Victor Reinz – Engine Coolant Outlet Gasket (Part No.71-39406-00)

Engine Coolant Outlet Gasket

from

$21.79
With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:
  • Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
See More

NTK – Engine Coolant Temperature Sensor (Part No.EF0086)

Engine Coolant Temperature Sensor

from

$29.99
The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:
  • OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
  • FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
  • THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor
See More

Behr – Blower Motor Regulat (Part No.R2041441822BEH)

Blower Motor Regulat

from

$137.18
Blower Motor Regulat

ACM – Heater Core (Part No.R3000275075ACM)

Heater Core

from

$107.17
ACM manufactures a direct fit Heater Core that guarantees OEM quality, fit and performance.

Product Features:
  • OEM Quality Direct fit Application
  • Meets or exceeds OEM specifications.
  • Utilizes the factory style mounts, connectors and fittings.
  • Provides exceptional reliability.
See More

Dorman – Blower Motor Resistor (Part No.973-113)

Blower Motor Resistor

from

$171.99
Blower motor resistor burnt out? Restore proper heating and cooling functionality with this direct replacement resistor designed to match the operation and performance of the original equipment on certain vehicles.

Product Features:
  • Direct replacement – this blower motor resistor matches the fit, function and performance of the original motor on specific vehicles
  • Restores performance – fixes a fan that’s only operating on one speed or not working at all
  • Thoroughly tested – examined and validated to perform safely and effectively
  • Trustworthy quality – backed by team of engineers and inspectors in the United States
See More

ACM – A/C Evaporator (Part No.R1130313395ACM)

A/C Evaporator

from

$255.69
ACM is a supplier of Original Equipment quality climate control products.
See More

Behr – BEHR A/C Condenser (Part No.R1030397213BEH)

BEHR A/C Condenser

from

$237.15
BEHR manufactures an OE-equivalent direct fit A/C Condenser that guarantees the same high quality, fit and performance of the OEM A/C condenser it replaces. BEHR produces brazed flat-tube condensers, delivering high power in spite of their small package size. This ensures rapid cooling of the vehicle cabin, thanks to optimum matching of heat transfer and pressure drop on the coolant side and air side.

Product Features:
  • OE-Equivalent and Direct fit Application.
  • Advanced technology parallel flow, sub cool and serpentine design.
  • Provides the fit, quality and performance of the original equipment.
  • compliant for both R12 and R134A refrigerants.
See More

KAI – Radiator Fan Assembly, 323/328I/Xi Sedan And Coupe (Part No.BM3117101)

Radiator Fan Assembly, 323/328I/Xi Sedan And Coupe

from

$394.99
New Platinum Pro Radiator Fan Assembly, 323/328I/Xi Sedan And Coupe

Product Features:
  • 323/328I/Xi Sedan And Coupe, Made Of Plastic
  • Meets All Federal Motor Safety Standards
  • No Drilling Needed For Installation
  • No Modifications Needed For Installation
  • Direct Fit Replacement For Your Vehicle
  • Same Form Fit And Function As OE
  • Check Out The Large Selection Of Parts Available For Your Vehicle
See More

Permatex – Sensor-Safe, High-Torque RTV Silicone Gasket Maker (Part No.82194)

Sensor-Safe, High-Torque RTV Silicone Gasket Maker

from

$11.49
Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:
  • High torque and rigidity
  • Sensor-safe, non-corrosive formula
  • OEM specified
  • Low-odor, non-corrosive formula
  • Ideal for closed spaced bolt patterns
See More

Rein – Aluminum Bolt Kit (Part No.HWK0034)

Aluminum Bolt Kit

from

$8.99
Rein OE quality bolts kits fit European vehicles the way the original manufacturer intended. Designed to be direct replacements for the original bolts are identical to OEM. Supplied with all the necessary bolts and torque specs to ensure that the job is done right.

Product Features:
  • Includes all the bolts needed to complete the job.
  • Comes with torque specs to make sure each bolt is properly tighten
  • Manufactured to strict engineering standards/specifications in materials and tolerances
  • Aluminum bolts are torque to yield and must be replaced once they are released.
See More

Rein – Water Pump Service Kit (Part No.WPS0501)

Water Pump Service Kit

from

$839.99
Rein OE Quality electric water pump replacement kits offer a valuable solution to failure prone cooling related components on the N51/2/4 BWM engine platforms. At the heart of these kits are OE electric water pumps and OE-quality thermostat assemblies which are complemented by Rein’s problem solver hoses and necessary mounting hardware. These kits ensure that the time consuming water pump repair is performed in a single effort, eliminating the possibility of a repeat repair. Replacing all related cooling system components at a suggested interval of 80,000 miles on this complicated engine platform and performing a proper coolant flush at the same time will ensure longevity of the system. The OE or Pentosin NF-G11 coolant is recommended for this repair.

Product Features:
  • Ensures proper operation of the cooling system
  • Helps to eliminate a repeat repair
  • Contains an OE electric water pump
  • Addresses the commonly failing plastic coolant hose connector
See More

ACM – ACM Blower Motor (Part No.R2031388878ACM)

ACM Blower Motor

from

$236.00
ACM manufactures a high quality replacement Blower Motor that meets or exceeds the vehicle manufacturer’s specifications for fit, durability and quality.

Product Features:
  • OE-Equivalent.
  • Direct Fit Replacement.
  • High quality OE electrical components.
  • OE quality brushes and bearings.
  • Balanced rotor assembly.
See More

ACM – Heater Core O-Ring Kit (Part No.R3002389082ACM)

Heater Core O-Ring Kit

from

$49.85
ACM is a supplier of Original Equipment quality climate control products.
See More

Original Equipment – A/C Pressure Switch (Part No.R1054668713OEA)

A/C Pressure Switch

from

$29.54
A/C Pressure Switch

Valeo – Air Flap Actuator (Part No.R2046700055VAL)

Air Flap Actuator

from

$124.15
Air Flap Actuator

Carquest Premium – AC Pressure Sensor (Part No.ABA1128)

AC Pressure Sensor

from

$85.99
The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:
  • Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
  • Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
  • All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
  • All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging
See More

Felpro – Multi-Purpose O-Ring (Part No.36057)

Multi-Purpose O-Ring

from

$8.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Manufactured for the sealing repair environment
  • Validated for fit, form, and function
  • Quality that you can trust
See More

Carquest Premium – Thermostat Kit: Gasket Included (Part No.85957)

Thermostat Kit: Gasket Included

from

$185.99
We are proud to offer this CARQUEST product line: CARQUEST Water Outlets. Our products are engineered and tested to provide years of trouble free operation and designed to be hassle free OE replacement part that meets and/or exceeds OE standards. Backed by over 50 years of mobile temperature control experience, fix it once and fix it right with CARQUST Water Outlets and Thermostat Housings.

Product Features:
  • Meets and/or exceeds OEM standard
  • Includes quality gasket or O-ring to ensure proper seal (where applicable)
  • 100% virgin resin material to insure durability
  • 100% leak tested
  • Direct-fit replacement for ease of installation
  • Includes quality thermostat
See More

Rein – Aluminum Bolt Kit (Part No.HWK0005)

Aluminum Bolt Kit

from

$6.29
Rein OE quality bolts kits fit European vehicles the way the original manufacturer intended. Designed to be direct replacements for the original bolts are identical to OEM. Supplied with all the necessary bolts and torque specs to ensure that the job is done right.

Product Features:
  • Includes all the bolts needed to complete the job.
  • Comes with torque specs to make sure each bolt is properly tighten
  • Manufactured to strict engineering standards/specifications in materials and tolerances
  • Aluminum bolts are torque to yield and must be replaced once they are released.
See More

ACM – A/C Evaporator Temperature Sensor (Part No.R1071273277ACM)

A/C Evaporator Temperature Sensor

from

$34.47
ACM is a supplier of Original Equipment quality climate control products. Heater / Evaporator Temperature Sensor
See More

Rein – Thermostat Assembly 97C (Part No.CTA0033)

Thermostat Assembly 97C

from

$84.99
Rein Automotive OE quality thermostat assemblies install, fit and perform the way the original manufacturer intended. These assemblies are designed to meet or exceed the OE materials used. Rein thermostat housings are constructed of metal or plastic based on vehicle specific factory requirements. The housings are constructed from molds cast directly from the OEM parts to meet the strict tolerances of the vehicle’s factory specifications. This ensures a smooth and easy installation, just as one would expect to find with OE quality. Rein thermostats are produced with high-quality metals and components to ensure proper durability and service life. The thermostats are temperature calibrated to have a consistent and precise response suiting cooling system needs. Our quality thermostat assemblies aim to provide the profession repair technician and vehicle owner the peace of mind and trust that is expected from an OE quality component.

Product Features:
  • Matches original equipment design specifications
  • Direct fitments allows easy installation
  • Manufactured to strict engineering standards/specifications in materials and tolerances
  • Thermostat set to 97 degrees Celsius to maintain optimal running temperature
See More

Carquest Premium – A/C Desiccant Bag Kit (Part No.T83077)

A/C Desiccant Bag Kit

from

$32.99
Carquest Accumulators and Receiver Driers are designed to store, filter and dry the air conditioning refrigerant to provide proper performance and durability for the air conditioning system. They are manufactured to meet or exceed original equipment specifications.

Product Features:
  • All parts meet or exceed original equipment standards for moisture absorption, pressure and temperature resistance, air tightness, vibration resistance, corrosiveness, and pulse pressure.
  • Desiccant is 100% tested and assembled in a controlled environment to ensure performance meets or exceeds original equipment standards.
  • All accumulators and receiver driers are helium leak tested prior to packaging.
  • O-Rings necessary for installation are included.
See More

Permatex – The Right Stuff Grey Instant Gasket Maker, 147ml Cartridge (Part No.34311)

The Right Stuff Grey Instant Gasket Maker, 147ml Cartridge

from

$28.49
Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:
  • Ideal for rigid cast aluminum parts
  • Meets OEM Specifications
  • Sensor safe & non-corrosive
  • Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
  • Blowout resistant, allowing leakproof gaskets to be made in just one minute
  • Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
  • Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
  • Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
  • Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.
See More

Original Equipment – Engine Cooling Auxiliary Thermo-Fan Switch (Part No.G5030151345OEA)

Engine Cooling Auxiliary Thermo-Fan Switch

from

$34.68
The Original Equipment Engine Cooling Thermo-Fan Switch is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:
  • Premium Original Equipment replacement
  • Provides performance and dependability
  • Manufactured to meet OE specifications
See More

Original Equipment – Coolant Level Sensor (Part No.G1050335088OEA)

Coolant Level Sensor

from

$25.60
Coolant Level Sensor

Dorman – Brass Coolant Air Bleeder Screw (Part No.902-404HP)

Brass Coolant Air Bleeder Screw

from

$8.79
This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:
  • Upgraded material – this brass coolant air bleeder screw reduces future maintenance costs by replacing the original equipment plastic screw on specified BMW, Mini, Chrysler, Dodge, Jeep, and Ram vehicles
  • Ideal solution – instead of wasting time wrestling with a deformed plastic screw head, this sturdy brass screw ensures easy, reliable removal and reuse
  • Durable construction – made of quality brass for reliable performance and long service life
  • Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
See More

Dorman – Coolant Air Bleeder Screw (Part No.902-404)

Coolant Air Bleeder Screw

from

$4.99
This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:
  • Ideal replacement – this engine coolant bleeder screw matches fit and function of the original equipment screw
  • Durable materials – designed to withstand high cooling system temperatures and pressures
  • Cost-effective solution – this bleeder screw offers original equipment quality at a competitive price
  • Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life
See More

2012 BMW 128i Cooling and Climate Controls

You count on your 2012 BMW 128i to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Cooling and Climate Controls. With 81 Cooling and Climate Controls ranging in price from $4.99 to $879.99, you’re sure to find everything you need for your 2012 BMW 128i.

Brands matter. If you want to shop a specific Cooling and Climate Controls brand, we stock 20 different brands like Permatex, Imperial, and Dorman. 2012 BMW 128i Cooling and Climate Controls start as low as $4.99!

One of the best ways to find top quality OEM or aftermarket Cooling and Climate Controls is by asking professionals. Short of that, you can shop with confidence thanks to our 1,064 extensive product reviews on 2012 BMW 128i Cooling and Climate Controls. Some of the top-rated Cooling and Climate Controls products we carry are Thermostatic Fan Control – Preset with 3.0 stars and Coolant Air Bleeder Screw with 3.4 stars.

Did we mention you can order your Cooling and Climate Controls from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Cooling and Climate Controls inventory for your 2012 BMW 128i below to get started!

Top-Rated Cooling and Climate Controls Brands For Your 2012 BMW 128i

Trusted Cooling and Climate Controls OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2012 BMW 128i running right for years to come. In our inventory you’ll find brands like Permatex, Imperial, Dorman, and even more.

Popular ACM Cooling and Climate Controls

You’ll find popular ACM brand products across Air Conditioning Parts. All are waiting to get your 2012 BMW 128i back on the road. Some of the top-rated ACM products in these categories are:
A/C Evaporator Temperature Sensor
from $34.47
(1)
A/C Evaporator Temperature Sensor
AC Evaporator Anti-Ice Sensors

Top-Rated Permatex Cooling and Climate Controls


If Permatex are what you’re looking for, our inventory holds plenty. We stock Permatex brand Cooling and Climate Controls for your 2012 BMW 128i, and some of our most reviewed Permatex parts include:
Water Pump & Thermostat RTV Silicone Gasket Maker, 0.5 OZ
from $6.99
(288)
Water Pump & Thermostat RTV Silicone Gasket Maker, 0.5 OZ
Engine Water Pump Inlet Pipe Gaskets
Sensor-Safe, High-Torque RTV Silicone Gasket Maker
from $11.49
(95)
Sensor-Safe, High-Torque RTV Silicone Gasket Maker
Water Pump Housing Gaskets
Sensor-Safe, High Torque RTV Silicone Gasket Maker
from $6.99
(9)
Sensor-Safe, High Torque RTV Silicone Gasket Maker
Engine Water Pump Inlet Pipe Gaskets

FAQs for 2012 BMW 128i Cooling and Climate Controls

What are the most purchased Cooling and Climate Controls for the 2012 BMW 128i?

Out of 81 Cooling and Climate Controls for the 2012 BMW 128i, the most popular in our inventory are:
Adjustable Thermostatic Fan Control
from $22.99
(35)
Adjustable Thermostatic Fan Control
Engine Cooling Fan Controllers
Electric Fan - 12" Diameter
from $94.99
(38)
Electric Fan – 12" Diameter
Radiator Fan Motors
Adjustable Thermostatic Fan Control
from $55.99
(33)
Adjustable Thermostatic Fan Control
Engine Cooling Fan Controllers

What are the top-rated 2012 BMW 128i Cooling and Climate Controls?

Top-rated Cooling and Climate Controls for your 2012 BMW 128i based on customer reviews/ratings are:
Thermostatic Fan Control - Preset
from $38.49
(8)
Thermostatic Fan Control – Preset
“I’ve been using this kit for several years on my off road truck. It’s hooked up to a powerful flex-a-lite fan and handles the load with ease. I have”
Coolant Air Bleeder Screw
from $4.99
(5)
Coolant Air Bleeder Screw
“Fixed the problem in 5mins….no more coolant leaking from my bleeder screw.”
Radiator
from $285.99
(5)
Radiator
“Excellent”