2010 Volkswagen Golf Heater Hoses
More 2010 Volkswagen Golf Heater Hoses
Find your specific 2010 Volkswagen Golf original or aftermarket Heater Hoses below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 2010 Volkswagen Golf Heater Hoses
MTC – Heater Hose Connector (Part No.R3036445089MTC)
from
$15.08
Heater Hose Connector
Vaico – Heater Hose Connecto (Part No.R3036445072VCO)
from
$13.02
Heater Hose Connecto
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 11 Inch Length (Part No.88454)
from
$25.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.19734)
from
$26.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 15 1/2 Inch Length (Part No.88439)
from
$30.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 7 Inch Length (Part No.86831)
from
$14.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Rein – Rein Heater Hose (Part No.R3030121912RIN)
from
$121.42
Designed to be direct replacements for OE hoses and assemblies, Rein hoses are identical, from the size and shape of their branches to the thermoplastic quick connect fittings when called for by the original manufacturer. Rein hose systems, feature integrated thermoplastic couplings, O-ring seals, and multiple connections that branch out to various engine components. Rein Automotive hoses are designed to fit just like the OE hose. No more cutting hoses to fit or repurposing old quick connect fittings.
Product Features:
See More
Product Features:
- Direct OE replacement for European cars
- Integrated thermoplastic couplings and O-ring seals
- Designed to go directly from the shelf to the vehicle. No cutting is ever needed
- All cooling-water hose inner linings are resistant to electrochemical cracking
- high strength and resistance to oil, mud, salt, road debris, and ozone
- Resistance to distilled water and water ethylene glycol mixtures
- Resistance to air temperatures of up to 135C
Gates – Premium Molded Heater Hose (Part No.18222)
from
$41.49
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Molded 90 Degree Heater Hose (Part No.28468)
from
$16.99
Specially designed for difficult heater hose applications requiring sharp 90 degree bends in the hose. Eliminates the need for extensive inventory of OE type curved heater hose. Just 22 sizes handle thousands of applications.
Product Features:
See More
Product Features:
- Resists electrochemical degradation and water permeation
- Use with heater hose connectors and bulk heater hose to create custom assemblies
- Compatible for coolant, air and water applications
- EPDM tube and cover, synthetic fiber reinforcement
- SAE 20R3 EC Class D1, SAE 20R4 EC Class D1
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 9/32 Inch Diameter, 16 Inch Length (Part No.86830)
from
$11.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Rein – Heater Hose (Part No.CHH0197P)
from
$86.99
Rein Automotive OE quality heater hoses fit European vehicles the way the original manufacturer intended. Designed to be direct replacements for OE hoses and hose assemblies, Rein hoses are identical to the OEM, from the size and shape of their branches to the thermoplastic quick connect fittings.
Product Features:
See More
Product Features:
- Reduces installation time.
- No cutting, refitting or adjusting the hose.
- Prevents leaks and comebacks from reusing old quick connectors and o-rings.
- Resistant to heat, salt, road debris, oil and other contaminants.
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 10 Inch Length (Part No.87723)
from
$22.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 10 Inch Length (Part No.88352)
from
$28.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 8 Inch Length (Part No.88377)
from
$14.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 7-1/2 Inch Length (Part No.86817)
from
$27.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each) (Part No.28408)
from
$1.79
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-3
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications.
Dayco – Molded Heater Hose; EPDM Rubber, 15/16 Inch Diameter, 20 1/2 Inch Length (Part No.88515)
from
$133.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose: EPDM Rubber, Direct Fit, 3/4" Inside Diameter (Part No.88453)
from
$16.29
Dayco Small I.D. Molded Heater Hose is designed to replace OEM coolant hose in applications where molded hose in small diameters (1″ I.D. or smaller) is required. The molded configuration eliminates the need for multiple connections of hoses and clamps. The knitted reinforcement and synthetic EPDM construction provides high strength and resistance to detrimental environmental elements, coolants, and temperature variations of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C). In addition to meeting SAE J20R4, Class D-1 requirements, this hose is designed to meet Type EC electro-chemical requirements as specified in SAE J1684. If the OE parts have a quick connect end, Dayco’s Small I.D. Molded Heater Hoses are also made with the quick connect assembled onto the hose for fast, convenient installation.
Product Features:
See More
Product Features:
- Made with a tough EPDM rubber compound this hose will resist the detrimental effects of heat, ozone and impacts from road debris
- This hose meets SAE J20R4, Class D1 and SAE J1684 Type EC specifications
- Highly resistant to electro-chemical degradation and premature stress cracking of the tube
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 14 3/4 Inch Length (Part No.87775)
from
$22.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – Premium Molded Heater Hose (Part No.19706)
from
$31.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 11 Inch Length (Part No.88502)
from
$16.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Rein – Rein Heater Hose (Part No.R303018006RIN)
from
$16.95
Designed to be direct replacements for OE hoses and assemblies, Rein hoses are identical, from the size and shape of their branches to the thermoplastic quick connect fittings when called for by the original manufacturer. Rein hose systems, feature integrated thermoplastic couplings, O-ring seals, and multiple connections that branch out to various engine components. Rein Automotive hoses are designed to fit just like the OE hose. No more cutting hoses to fit or repurposing old quick connect fittings.
Product Features:
See More
Product Features:
- Direct OE replacement for European cars
- Integrated thermoplastic couplings and O-ring seals
- Designed to go directly from the shelf to the vehicle. No cutting is ever needed
- All cooling-water hose inner linings are resistant to electrochemical cracking
- high strength and resistance to oil, mud, salt, road debris, and ozone
- Resistance to distilled water and water ethylene glycol mixtures
- Resistance to air temperatures of up to 135C
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 6 Inch Length (Part No.80411)
from
$7.79
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Original Equipment – Heater Hose (Part No.R3030447331OEA)
from
$345.07
Heater Hose
Rein – Heater Hose (Part No.CHH0147R)
from
$139.99
Rein Automotive OE quality heater hoses fit European vehicles the way the original manufacturer intended. Designed to be direct replacements for OE hoses and hose assemblies, Rein hoses are identical to the OEM, from the size and shape of their branches to the thermoplastic quick connect fittings.
Product Features:
See More
Product Features:
- Reduces installation time.
- No cutting, refitting or adjusting the hose.
- Prevents leaks and comebacks from reusing old quick connectors and o-rings.
- Resistant to heat, salt, road debris, oil and other contaminants.
Dayco – Molded Heater Hose; EPDM Rubber, 7/8 Inch Diameter, 13 1/2 Inch Length (Part No.88503)
from
$32.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Rein – Heater Hose (Part No.CHH0572)
from
$29.99
Rein Automotive OE quality heater hoses fit European vehicles the way the original manufacturer intended. Designed to be direct replacements for OE hoses and hose assemblies, Rein hoses are identical to the OEM, from the size and shape of their branches to the thermoplastic quick connect fittings.
Product Features:
See More
Product Features:
- Reduces installation time.
- No cutting, refitting or adjusting the hose.
- Prevents leaks and comebacks from reusing old quick connectors and o-rings.
- Resistant to heat, salt, road debris, oil and other contaminants.
Dorman – Molded Heater Hose: Rubber/Plastic (Part No.626-524)
from
$19.99
This replacement HVAC heater hose assembly is engineered to match the fit and durability of the stock heater hose assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.
Product Features:
See More
Product Features:
- Ideal replacement – this HVAC heater hose assembly directly replaces the original heater hose on specified vehicle years, makes and models
- Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
- Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
- Industry-leading design – professionally engineered by the aftermarket leader in heater hose assemblies
Popular 2010 Volkswagen Golf Heater Hoses Categories
2010 Volkswagen Golf Heater Hoses
Maybe you’re in the middle of a full rebuild of that 2010 Volkswagen Golf. Maybe you just need a couple of Heater Hoses. Either way, Advance Auto Parts has 4 different Heater Hoses in our inventory ranging from $11.29 to $345.07. That means you can find the exact parts or products you need to keep that 2010 Volkswagen Golf running smoothly.
Heater Hoses are only as good as their brand. We stock 4 different brands to make sure you have plenty of trusted parts to choose from for your 2010 Volkswagen Golf. Dayco, MTC, and Original Equipment are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Heater Hoses for your 2010 Volkswagen Golf, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Heater Hoses to keep your 2010 Volkswagen Golf rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Heater Hoses Brands To Make Your 2010 Volkswagen Golf Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 2010 Volkswagen Golf demands trusted brand parts and products to keep it running. Many trusted brands of Heater Hoses make up Advance Auto Parts’ inventory, and all are ready to help make your Golf the best it can be. Be sure to browse some of our top Heater Hoses brands and parts.
FAQs for 2010 Volkswagen Golf Heater Hoses
What are the most purchased Heater Hoses for the 2010 Volkswagen Golf?
Out of 4 Heater Hoses for the 2010 Volkswagen Golf, the most popular in our inventory are:
from
$11.29
This product is not rated
Molded Heater Hose; EPDM Rubber, 9/32 Inch Diameter, 16 Inch Length
Heater Hoses
