from

$145.99

Using advanced re-engineering materials and processes, our master cylinders match O.E. performance and fitment. New O.E.-quality seals and cups are installed on each unit, ensuring leak-free, long-lasting performance. Cast-iron master cylinders are treate

Product Features:

Only new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Bleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Bores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Cast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Piston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Plastic reservoirs are vacuum-tested to ensure they are leak free.

from

$5.44

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$56.09

Parking Brake Cable

from

$244.12

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$37.99

ACDelco Professional Cornering Light Socket is a high quality aftermarket replacement component for one or more of the following vehicle systems: ignition, starting and charging, body-electrical and lighting, and/or engine fuel management. This premium aftermarket socket is manufactured to meet or exceed your expectations for fit, form, and function.

Product Features:

Professional, premium aftermarket replacement
Provides the performance and dependability you expect from ACDelco
Manufactured to meet expectations for fit, form, and function

from

$54.99

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

Application-specific formulations designed for extended pad life and clean wheels
Multi-layer shim for near silent braking
OE designed slots and chamfers for consistent performance
Hardware included on popular and late-model applications

from

$148.99

For over 25 years Hawk Performance has been producing premium friction products that stop you faster and last longer. Whether you are looking to cut seconds off of your track time, need additional stopping power for your large vehicle, want a product that is cleaner and quieter or, just don’t want to have to think about brakes and rotors, Hawk Performance has the products to keep you safer. We leverage our experience on the track and the technology used in aerospace and the military to make the best brake pads and rotors for all of your vehicle’s needs. Our extensive Research & Development department, including a PhD in friction and 23 dynamometers, allows us to produce first class products in the USA.

Product Features:

Low to mid temperature range
Fade resistant
Smooth & predictable torque
Ideal for Autocross & club racing events
All Hawk Performance compounds are not compatible with carbon ceramic rotors. Hawk pads are designed to work with Iron/Metal rotors.

from

$5.79

Brakes are designed as a system and all the parts need to work together for best performance. The boot and square cut seals included in our Caliper Repair Kit, ensure that the caliper works as designed during the apply and release cycle.

Product Features:

This part matches Original Equipment (OE) quality specifications
Increases the life span of the brake pads
Restores brakes to like-new performance
Prevents noise and premature wear
Direct replacement for a proper fit

from

$143.20

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$181.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$222.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Buy with confidence from the originator & industry leader of brake kits

from

$7.49

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. Caliper Guide Pins are important to replace because they hold the brake piston in place to create effective stopping performance.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Helps deliver a quieter, more efficient braking system
Corrosion resistant coating for long-lasting durability against harsh roads
Manufactured with quality materials to suppress high stress levels

from

$16.99

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
New Brake Hardware prevents premature wear and maximizes performance
Helps deliver a quieter, more efficient braking system
Manufactured with quality materials to suppress high stress levels

from

$15.29

Brakes are designed as a system and all the parts need to work together for best performance. Industry brake service experts agree – when brake friction materials are ready to be replaced, the hardware is too. A complete brake job that includes new hardware goes a long way toward preventing comebacks. Changing out your Rubber Pin Boot or Slider Bushing Kit will ensure the guide pins are clean and free from debris for smoother braking.

Product Features:

This part matches Original Equipment (OE) quality specifications
Easy and fast replacement
Prevents noise and premature wear
Provides longer brake life and performance

from

$258.84

Brake Vacuum Pump

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$21.10

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$33.99

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
Quality assured – materials tested to exacting government-regulated safety and durability standards
Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings
Brand may vary by location

from

$263.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Buy with confidence from the originator & industry leader of brake kits

from

$252.99

PowerStop is on a mission to deliver an easy way for any driver to upgrade their brakes – no matter where or how they use their vehicle. Forget standard, off-the-shelf parts. Our Z23 Evolution Sport Brake Upgrade Kit comes with everything you need, from pads, rotors and premium stainless-steel hardware for an easy, bolt-on upgrade for your daily-driver. Along with increased braking power, the Carbon-Fiber Ceramic brake pads feature a low-dust formula to keep those wheels looking great while you say goodbye to nasty brake dust. These pads combine with Drilled & Slotted rotors to ensure a cool, smooth ride that protects against rust and corrosion. Give your daily-driver the easy and affordable performance upgrade it deserves with the Z23 Evolution Sport Brake Upgrade Kit.

Product Features:

This complete upgrade kit is engineered to improve the braking performance of the vehicle you use everyday
PowerStop engineered Carbon-Fiber Ceramic Z23 compound significantly enhances braking performance versus traditional ceramic brake pads
Low-dust braking validated through on-vehicle 3rd party tests in Los Angeles, showing on average 30% less dust versus OE
Multi-Layer rubberized shims provide virtually noise-free braking
Drilled & Slotted performance rotors provide maximum cooling
Includes stainless-steel installation hardware and high-temperature ceramic brake lubricant
Bolt-on upgrade for stock brakes, no modifications necessary
Brake rotor, pad & hardware engineered to work together to increase stopping power, improve durability & eliminate dust
Rotors are zinc plated for maximum protection against rust.
Buy with confidence from the originator & industry leader of brake kits

from

$131.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$131.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$210.04

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features: