2010 Nissan Altima Belts and Hoses
More 2010 Nissan Altima Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2010 Nissan Altima, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2010 Nissan Altima Belts and Hoses
NSK – Acc. Belt Idler Pull (Part No.G6020313993NSK)
from
$41.98
Acc. Belt Idler Pull
Gates – DriveAlign« Belt Drive Idler/Tensioner Pulley (Part No.36087)
from
$46.99
Gates is a leading manufacturer of Original Equipment (OE) idler pulleys. Gates DriveAlign(R) Idler Pulleys meet or exceed OE specifications. High quality, high strength bearings run cooler and last longer than original bearings. DriveAlign Idler Pulleys are built to last by resisting dirt, salt, and other under-hood contaminants. Designed for use on automobiles and light trucks as locked center tensioning, automatic belt tensioning and idler pulleys.
Product Features:
See More
Product Features:
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Dorman – Fuel Filler Neck Hose (Part No.573-163)
from
$39.99
Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair..
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles.
- Durable construction – made of fuel-resistant materials to reduce future failure potential
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999607A)
from
$90.99
This Litens supplied tensioner is manufactured to original equipment specifications. This part is specifically designed for Nissan w/2.5L applications. Heavy duty thermoplastic pulley construction ensures long life and trouble-free performance. This tensioner meets or exceeds all original equipment fit, form, and performance characteristics. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Heavy duty thermoplastic pulley construction.
- OE-spec sealed ball bearings with synthetic grease and double lip seals for long life
- Install pin included for ease of installation
- Installation instructions included
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999502A)
from
$70.99
This accessory drive tensioner is designed and engineered by Litens – the world’s largest supplier of original equipment (O.E.) belt tensioners in the world. This part was designed for the 2013-2018 Nissan Altima,Pathfinder,Murano, Quest / 2013 Infiniti JX35 / 2014-2015 Infiniti QX60 with 3.5L. The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part. This part is manufactured to meet or exceed the performance and life specifications of the O.E. part. The part features a premium chrome-silicon steel spring, internal damping, a lift-lug feature for ease of installation, a 6203 ball bearing and a plastic pulley molded to exacting specifications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Designed and engineered by the world’s largest Original Equipment supplier of accessory drive tensioners and pulleys.
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- A plastic pulley specifically molded with tight radial run out for reduced noise and longer life
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt. Belt removal is required to change the tensioner. Therefore, d
- Installation instructions included
Gates – Premium Molded Coolant Hose (Part No.22963)
from
$27.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 22.5" Long, 1.38" Diameter (Part No.E72590)
from
$33.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium 5/16 X 50 Ft Heater Hose by Gates (sold by each) (Part No.28408)
from
$1.79
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time
- Similar to SAE 20R3 Class D-3
- Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications.
Dayco – Molded Heater Hose; EPDM Rubber, 3/4 Inch Diameter, 17 1/2 Inch Length (Part No.88469)
from
$14.49
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 84mm Dia., 25mm Width, Smooth (Part No.89134)
from
$40.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 80.8mm Dia., 18.9mm Width, 4 Grooves (Part No.89575)
from
$54.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Bando – Multi Rib (Serpentine) Belt (Part No.W100026491BAN)
from
$11.09
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Bando – Multi Rib (Serpentine) Belt (Part No.W100054383BAN)
from
$34.78
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Gates – Premium Molded Coolant Hose (Part No.22965)
from
$25.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 2 Inch Long, 1.25 Inch Inner Dia. (Part No.81061)
from
$30.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 19.5" Long, 1.38" Diameter (Part No.E72598)
from
$29.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18" Long, 1.31" Diameter (Part No.E72148)
from
$23.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.80402)
from
$23.49
Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- Meets Type EC electro-chemical requirements as specified in SAE J1684
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.75" Inside Diameter (Sold by foot) (Part No.28412)
from
$3.99
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Dayco – Serpentine Belt Kit; With 2 Belts and Pulley, 3 Piece Set (Part No.5060423K1)
from
$48.49
Dayco believes in a systems approach to maintenance and has a full line of serpentine belt kits that have been designed for the most popular light-duty applications, ensuring that whomever is completing the repair has all the parts needed. Dayco’s kit offers everything to service your front-end accessory drive with OE or equivalent components. This can include a premium tensioner with flat spring technology, durable pulley(s) with permanently lubricated bearings, a Dayco ela (stretch) serpentine belt, and the Dayco serpentine belt that provides extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Engineered to match OE specifications with unique features that enhance vehicle performance and safety
- For vehicles that need a highly engineered drive belt and multiple parts for a thorough and proper repair
- Provides all the parts needed in one box, helping simplify installation
Litens – Serpentine Belt Tensioner Kit: Includes Belt, Tensioner, and any applicable Idler Pulleys (Part No.LV999601C)
from
$74.99
This Litens Serpentine Belt Drive Component Kit fits 2002-2006 Nissan Altima, Sentra w/2.5L. These kits make it easy to maintain your entire front end accessory drive system. Eliminate the need to search for individual parts by purchasing this all-in-one solution. Front end accessory drives require maintenance at specific intervals, and parts should be replaced as part of your regularly scheduled tune-up to ensure your vehicle is at its best. Each kit contains a Litens belt tensioner, Bando serpentine belt, and any necessary idler pulley(s). All required hardware is included for the installation . Application specific instructions are also conveniently included. All parts meet or exceed OE fit, function, and performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Driveworks – Poly Rib Belt Serpentine Belt; 30.51 Long, 4 Rib Count (Part No.305K4)
from
$34.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Dayco – Poly Rib Belt Serpentine Belt; 52.56 Long, 6 Rib Count (Part No.5060525)
from
$41.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Dayco, Heater Hose, 90 Trim-to-Fit (Part No.R3030752627DAY)
from
$16.22
Dayco, Heater Hose, 90 Trim-to-Fit
Popular 2010 Nissan Altima Belts and Hoses Categories
2010 Nissan Altima Belts and Hoses
You count on your 2010 Nissan Altima to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 59 Belts and Hoses ranging in price from $0.99 to $284.99, you’re sure to find everything you need for your 2010 Nissan Altima.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 12 different brands like Dayco, Driveworks, and Gates. 2010 Nissan Altima Belts and Hoses start as low as $0.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 447 extensive product reviews on 2010 Nissan Altima Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.31" Diameter with 3.7 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 20.5" Long, 1.34" Diameter with 5.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2010 Nissan Altima below to get started!
Top-Rated Belts and Hoses Brands For Your 2010 Nissan Altima
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2010 Nissan Altima running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Gates, and even more.
Popular Dayco Belts and Hoses
You’ll find popular Dayco brand products across Serpentine and V Belts and Engine Cooling Hoses. All are waiting to get your 2010 Nissan Altima back on the road. Some of the top-rated Dayco products in these categories are:
from
$63.99
(3)
Serpentine Idler/Tensioner Pulley; Steel, 75mm Dia., 35.5mm Width, Smooth
Drive Belt Idler Assemblies
from
$32.49
(2)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 23" Long, 1.31" Diameter
Upper Radiator Hoses
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2010 Nissan Altima, and some of our most reviewed Dayco parts include:
from
$33.99
(31)
Serpentine Idler/Tensioner Pulley; Steel, 82mm Dia., 27mm Width, Smooth
Idler Pulleys
from
$63.99
(20)
Serpentine Belt Tensioner: 1 Piece, Built To Outperform And Outlast OE Parts
Belt Tensioner Assemblies
FAQs for 2010 Nissan Altima Belts and Hoses
What are the most purchased Belts and Hoses for the 2010 Nissan Altima?
Out of 59 Belts and Hoses for the 2010 Nissan Altima, the most popular in our inventory are:
What are the top-rated 2010 Nissan Altima Belts and Hoses?
Top-rated Belts and Hoses for your 2010 Nissan Altima based on customer reviews/ratings are:
from
$19.49
(16)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.31" Diameter
“It fit the old Tundra.”
from
$31.99
(4)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 20.5" Long, 1.34" Diameter
“This was much better than the used part I tried”
from
$153.99
(3)
Serpentine Belt Tensioner: 1 Piece
“Have been using this part for a few months now and its held up just fine. The process to finding this noise was something else I seriously thought my ”
