Name: Differential Ring Gear Bolt
Brand: Pro-King
SKU: 761A935
Price: 0.99 USD

from

$0.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$21.99

Crush Sleeve for Grand Cherokee front & “super” 30, APROX 2.400″.

Product Features:

Crush sleeve for Dana Spicer “super” 30 front
2.40″ tall

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$7.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$83.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$12.99

Product Features:

Cross pin shaft for Dana Spicer 30
Fits standard open differentials only

from

$199.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits AMC Model 35 IFS
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$11.79

Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

from

$37.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$8.99

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 8.8″
0.750″ I.D.

from

$329.99

Yukon positraction internals for 8.8″ Ford with 31 spline axles. This kit fits Yukon Gura Grip & Eaton positractions. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 8.8″ with Yukon Dura Grip positraction with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles.
Quality materials – all components are built for reliable longevity and performance.
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$246.99

Yukon forged yoke for Ford 8.8″ with a 1350 U/joint size (stronger than billet). 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$299.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 31 spline Trac Loc positraction
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$1303.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

Fits Dana Spicer 30 with 27 spline axles
3.73 and up ratio only
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

from

$194.99

Mini Spool for Ford 8.8″ with 31 spline axles and 7/8″ cross pin. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″ with 31 spline axles
Provides 100% traction to both wheels at all times
Installs into standard open carrier case

from

$463.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$108.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG.&SEAL FORD 8.8

from

$359.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Ford 8.8″ IRS in SUV applications
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles.
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged.
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$3.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$11.99

Side gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

Side gear thrust washer for Ford 8.8″
0.875″ diameter cross pin shaft applications only

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience