from

$87.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$234.99

Yukon cast yoke for GM 8.5″ with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$41.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$115.84

Axle Differential Be

from

$7.99

Differential Cover B

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$254.99

This kit uses Koyo bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and br

Product Features:

Fits 2009 and up GM 8.6″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$57.99

Cross pin shaft for 7.5″, 7.625″, and 8″ GM.

Product Features:

Cross pin shaft for GM 7.5″, 7.625″ and 8.0″
Fits standard open differentials only

from

$569.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits GM 8.0″
8.0″ ring gear diameter
27 spline pinion
10 ring gear bolts
4.11 ratio

from

$12.99

Product Features:

KIT SHIM

from

$6.99

Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:

Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
7/16″ x 20

from

$6.59

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$13.49

Product Features:

Brand may vary by location

from

$22.72

Pinion Seal

from

$72.99

DiffrlCover

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$239.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 1999-2008 GM 8.6″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
7/8″ x 14 thread
1 1/4″ socket

from

$819.99

Hard use and poor lubrication can wear out a limited-slip differential. Restore original performance with this replacement differential carrier assembly that includes all-new spider gears, differential pins, clutches and carrier housing.

Product Features:

Direct replacement – this 30 spline limited-slip differential carrier fits in place of this vehicle’s original equipment carrier.
100% new – this differential carrier uses all-new components, including spider gears, diff pin, pre-load spring pack and clutch pack.
Ready to install – this differential carrier is shipped pre-assembled and ready to install
Ideal upgrade – can be used to upgrade from open differential to limited-slip in an existing differential

from

$231.58

More like a complete kit than a single part, Dorman’s Four-Wheel Drive (4WD) Actuator comes with all the parts needed to complete the repair. Since this part is a direct replacement, the exact fit adds another layer of efficiency and convenience.

Product Features:

Includes all necessary gaskets and seals (where applicable)
Sealed for leak resistance
Engineered for durability against harsh road and weather conditions, including water intrusion
Quality tested to ensure trouble free installation and performance

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$929.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.

Product Features:

Fits GM 8.5″ and 8.6″ with 30 spline axles
2.73 ratio and up only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$5.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Side gear thrust washer
Fits GM 8.0″

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience