2010 Chevrolet Impala Wheels and Tires
More 2010 Chevrolet Impala Wheels and Tires Categories
If you’re looking for an original Wheels and Tires replacement for a 2010 Chevrolet Impala, you can search through our selection below. You’ll also find aftermarket and OEM Wheels and Tires to meet your needs.
Essential 2010 Chevrolet Impala Wheels and Tires
ACDelco – Tire Pressure Monitoring System (TPMS) Sensor (Part No.20925924)
from
$114.99
ACDelco GM Original Equipment Tire Pressure Monitoring Sensors (TPMS) are battery powered sensors located in the tire that monitor the vehicle’s tire pressure and warn the driver when pressure falls more than 25% below the manufacturer’s recommendations (normally through a slow pressure loss), and are GM-recommended replacements for your vehicle’s original components. The sensor is connected with the valve stem and, by way of Radio Frequency (RF) technology, sends pressure updates to the vehicle’s on-board computer. Tire pressure is displayed on the vehicle’s Driver Information Center (DIC) or, when low, a warning light may be illuminated to warn the driver. U.S. Federal Regulations require that new cars and light trucks be equipped with TPMS starting in 2008. These original equipment tire pressure monitoring sensors have bn manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Battery is made to last up to 10 years of normal use
- Designed to communicate perfectly with your GM vehicle’s TPMS Module
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Carquest Premium – Keyless Entry Module Connector (Part No.PTC2161)
from
$99.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.
Product Features:
See More
Product Features:
- CarQuest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Dorman – Wheel Lug Nut: 1/2-20 Thread, Flanged, Cragar SST Mag, 2.24" Length, Chrome (Sold by each) (Part No.611-157)
from
$3.79
These wheel lug nuts are designed to match the fit, function and performance of the original equipment hardware on specified vehicles. They are engineered from durable materials to exacting specifications for long service life and a perfect fit.
Product Features:
See More
Product Features:
- Direct replacement – these wheel lug nuts are designed to match the fit, function and performance of the original equipment hardware on specified vehicles
- Ensure fit – available in a variety of sizes and assortments, please check product dimensions and details to ensure you select the right wheel lug nut(s) for your application
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Dorman – 16 X 6.5 In. Steel Wheel (Part No.939-138)
from
$98.99
Damaged your wheel, or looking to upgrade? This wheel is specifically designed to directly replace the original wheel on certain vehicle applications. It is thoroughly tested to meet safety standards for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this wheel is designed to match the fit and structural appearance of the original wheel on specific vehicle years, makes and models
- Cost-effective solution – offers original equipment quality and appearance for a competitive price
- Thoroughly tested – dynamic radial testing, radial run-out testing, and axial run-out testing ensures performance
- Trustworthy quality – backed by team of designers and engineers in the United States
Dorman – Hub And Bearing Mounting Bolts, Pack of 3 (Part No.917-503)
from
$20.99
Wheel hub bolts rounded off or have damaged threads? These wheel hub bolts are designed to match the performance of original equipment bolts to secure the hub to the knuckle/spindle on specified vehicles.
Product Features:
See More
Product Features:
- Direct replacement – these wheel hub bolts are designed to match the performance of the original bolts on specified vehicles
- Ideal solution – made of durable materials to reliably replace bolts with rounded-off or damaged threads
- Application-specific – precision-manufactured to securely mount the hub to the vehicle knuckle/spindle
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Dorman – Wheel Lug Nut: 7/16-20 Thread, Conical 60, OEM Style, 0.542" Length, Chrome, 4 Pack (Part No.711-830)
from
$8.29
These wheel lug nuts are designed to match the fit, function and performance of the original equipment hardware on specified vehicles. They are engineered from durable materials to exacting specifications for long service life and a perfect fit.
Product Features:
See More
Product Features:
- Direct replacement – these wheel lug nuts are designed to match the fit, function and performance of the original equipment hardware on specified vehicles
- Ensure fit – available in a variety of sizes and assortments, please check product dimensions and details to ensure you select the right wheel lug nut(s) for your application
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Dorman – Wheel Lug Nut Cover: M24-2.0 Thread, 19 mm Hex, 38.57 mm Depth, Plastic, Metal Blk (Sold by each) (Part No.611-640)
from
$3.79
This wheel fastener cover is designed to precisely fit the factory wheel hardware while providing a clean, finished appearance. Made of quality materials for durability, this cover has been dimensionally validated for specific applications.
Product Features:
See More
Product Features:
- Correct fit – this wheel fastener cover is designed to precisely fit the factory wheel hardware while providing a clean, finished appearance
- Quality materials – manufactured for durability and a quality finish
- Simple installation – no special tools required
- Quality tested – this part has undergone dimensional testing to ensure a quality fit
Schrader – TPMS Sensor Service Kit (Part No.20018)
from
$3.49
Schrader service kits are essential for TPMS sensor installation in today’s modern vehicles. Schrader’s high-quality components and proper installation help customers stay safe on the road and save money with their TPMS-enabled vehicles. Service kit components may include but are not limited to a valve core, sealing cap, grommet, nut, or valve stem. All pieces in a kit are intended for one-time use only and must be replaced with every tire change. TPMS sensors and service Kits are not DIY products and require appropriate expertise, knowledge, and equipment for successful service.
Product Features:
See More
Product Features:
- DIRECT REPLACEMENT: kit components are designed to replace original manufacturer parts
- DURABLE: Service Kits are constructed of high-quality materials to help ensure reliable performance and long service life
- SCHRADER QUALITY: Schrader is a leading global manufacturer of both OE and aftermarket TPMS sensors
- VEHICLE FIT: Each service Kit is tailored to a specific vehicle make, model, and year
- PROPER SERVICE: kits are intended for one-time use only and must be replaced with every tire change
- Professional installation is strongly suggested
- The programmable sensors come blank and must be programmed using a compatible TPMS programming tool
- Once programmed, the sensor performs identically to OEM direct-fit sensors
Schrader – TPMS Sensor Service Kit (Part No.20004)
from
$2.99
Schrader service kits are essential for TPMS sensor installation in today’s modern vehicles. Schrader’s high-quality components and proper installation help customers stay safe on the road and save money with their TPMS-enabled vehicles. Service kit components may include but are not limited to a valve core, sealing cap, grommet, nut, or valve stem. All pieces in a kit are intended for one-time use only and must be replaced with every tire change. TPMS sensors and service Kits are not DIY products and require appropriate expertise, knowledge, and equipment for successful service.
Product Features:
See More
Product Features:
- DIRECT REPLACEMENT: kit components are designed to replace original manufacturer parts
- DURABLE: Service Kits are constructed of high-quality materials to help ensure reliable performance and long service life
- SCHRADER QUALITY: Schrader is a leading global manufacturer of both OE and aftermarket TPMS sensors
- VEHICLE FIT: Each service Kit is tailored to a specific vehicle make, model, and year
- PROPER SERVICE: kits are intended for one-time use only and must be replaced with every tire change
- Professional installation is strongly suggested
- The programmable sensors come blank and must be programmed using a compatible TPMS programming tool
- Once programmed, the sensor performs identically to OEM direct-fit sensors
Dorman – Pik-a-Nut – Wheel Stud : Serrated Stud, 1/2-20 Thread Size, RHT, 1 Pack (Part No.98157.1)
from
$3.29
These wheel lug studs are made of carbon steel and tested to demanding automotive industry standards to ensure strength, longevity and safety.
Product Features:
See More
Product Features:
- Durable material – carbon steel meets SAE automotive industry standards for strength and hardness
- Corrosion resistant – extensive salt spray testing helps ensure years of durability against rust
- Tensile tested – lug studs undergo industry-standard proof-load testing to ensure strength
- Trustworthy quality – backed by team of professional engineers and quality control specialists in the United States
Autel – Component Kit for Rubber & Metal MX-Sensors: Valves, Caps, Cores, Nuts & Washers (Part No.MXSENSORCK)
from
$68.99
Component Kit includes a complete list of individual parts needed to service and replace existing rubber and metal valve stem Autel MX-Sensors. The smaller storage case keeps your replacement parts organized and easily within arms reach during your repair projects.
Product Features:
See More
Product Features:
- MX-Sensor Components
- 4 Metal Valves
- 4 Rubber Valves
- Rubber Gasket (2×10 pcs)
- Screw Nut (2×10 pcs)
- Washer (2×10 pcs)
- Metal Valve Cap (2X10 pcs)
- Rubber Valve Cap (2X10 pcs)
- Valve Core (2X10 pcs)
Autel – MX-Sensor 1-Sensor Bulk Box 240 (Part No.300050)
from
$7321.99
The 300050 is a convenient bulk box of 240 individually bagged Autel MX-Sensor 1-Sensors. The 1-Sensor is a programmable universal TPMS sensor. It features a combined frequency of 315MHz and 433MHz with rubber valve stems. The press release button allows for rubber or metal valve stems to be replaced interchangeably. The 1-Sensor is reprogrammable, 99 percent compatible with OE sensors, and meets SAE standards J1205 and J1206. Replacement valve stems are available for purchase in rubber or metal.
Product Features:
See More
Product Features:
- Bulk Box of (240) Individually Bagged 1-Sensors with Rubber Press-in Valve
- Bulk Box of 240 Individually Bagged 1-Sensors with Rubber Press-in Valve
- Combined Frequency 315MHz and 433MHz
- Programmable with Autel TPMS Service Tools
- Program to Replace 99% of OE Sensors
- Compatible with Autel Interchangeable Rubber, Aluminum or Color Metal Valve Stems
- Compatible with Autel Interchangeable Rubber, Aluminum or Color Metal Valve Stems
- Maximum Signal Strength / Battery Reliability
- Maximum Signal Strength, Battery Reliability
- Professional installation is strongly suggested
- The programmable sensors come blank and must be programmed using a compatible TPMS programming tool
- Once programmed, the sensor performs identically to OEM direct-fit sensors
Driveworks – Wheel Bearing and Hub Assembly: 5 Studs (Part No.NT513282)
from
$169.99
WJB Automotive wheel hub assemblies are made with high precision through state-of-the-art technology and manufactured with strict quality-control criteria. Every wheel hub assembly is specifically designed to fit the designated applications and may be used as a direct replacement for the original part. Each part is engineered using OE data and measurements to ensure fitment, performance, and longevity.
Product Features:
See More
Product Features:
- Fitment and function are ensured by precision machining, rigorous testing, and meticulous inspection of material and components.
- WJB Automotive wheel hub assemblies are designed to meet stringent fatigue requirements in order to reduce premature failure.
- Reinforced seal design material allows for optimal performance in harsh environments.
- WJB Automotive wheel hub assemblies undergo heat treatment and cold-forming processes that harden the surface ensuring high-temperature resistance and durability.
- Where applicable, pre-installed speed sensors will automatically sync to the vehicle’s anti-lock braking system upon successful installation and provide accurate speed-reading data.
- Brand may vary by location
Schrader – TPMS Ni Plated Valve Core, 100 Pack (Part No.20055-100)
from
$23.99
Schrader service components are essential for TPMS sensor installation in today’s modern vehicles. Schrader’s high-quality components and proper installation help customers stay safe on the road and save money with their TPMS-enabled vehicles. All Schrader service components are intended for one-time use only and must be replaced with every tire change. Each service component is tailored to a specific vehicle make, model, and year. TPMS sensors and service Kits are not DIY products and require appropriate expertise, knowledge, and equipment for successful service.
Product Features:
See More
Product Features:
- DIRECT REPLACEMENT: Service components are designed to replace original manufacturer parts
- DURABLE: Service components are constructed of high-quality materials to help ensure reliable performance and long service life
- SCHRADER QUALITY: Schrader is a leading global manufacturer of both OE and aftermarket TPMS sensors
- VEHICLE FIT: Each service component is tailored to a specific vehicle make, model, and year
- PROPER SERVICE: Service components are intended for one-time use only and must be replaced with every tire change
- Professional installation is strongly suggested
- The programmable sensors come blank and must be programmed using a compatible TPMS programming tool
- Once programmed, the sensor performs identically to OEM direct-fit sensors
Driveworks – Wheel Bearing and Hub Assembly: 5 Studs (Part No.NT513288)
from
$147.99
WJB Automotive wheel hub assemblies are made with high precision through state-of-the-art technology and manufactured with strict quality-control criteria. Every wheel hub assembly is specifically designed to fit the designated applications and may be used as a direct replacement for the original part. Each part is engineered using OE data and measurements to ensure fitment, performance, and longevity.
Product Features:
See More
Product Features:
- Fitment and function are ensured by precision machining, rigorous testing, and meticulous inspection of material and components.
- WJB Automotive wheel hub assemblies are designed to meet stringent fatigue requirements in order to reduce premature failure.
- Reinforced seal design material allows for optimal performance in harsh environments.
- WJB Automotive wheel hub assemblies undergo heat treatment and cold-forming processes that harden the surface ensuring high-temperature resistance and durability.
- Where applicable, pre-installed speed sensors will automatically sync to the vehicle’s anti-lock braking system upon successful installation and provide accurate speed-reading data.
- Brand may vary by location
Dorman – Hub Bearing Assembly (Part No.4110309)
from
$94.99
To prevent damages to your spindle, wheels and hubs we offering replacement Wheel Bearing and Hub Assemblies. All our Wheel Bearing and Hub Assemblies are direct replacements for a proper fit.
Product Features:
See More
Product Features:
- Constructed from high-quality materials for extended durability
- Manufactured to strict engineering quality standards
- Replacement eliminates noises associated with original failure
- Axles also available, sold separately
Dill Air Control – Clamp-In TPMS Service Kit: Metal, 0.453 Inch Black Anodized Valve Stem (Part No.VS925B)
from
$9.49
Dill is the leader in the automotive aftermarket for TPMS replacement sensors, stems, kits, and tools.
Product Features:
See More
Product Features:
- Black anodized clamp-in stem for GM, Ford, Chrysler/Dodge/Jeep, Subaru
- 0.453″ rim hole compatibility
- 200 PSI maximum cold inflation pressure
Dill Air Control – Snap-In TPMS Service Kit: Rubber, 0.453 Inch Stem (Part No.VS950)
from
$4.49
Dill is the leader in the automotive aftermarket for TPMS replacement sensors, stems, kits, and tools.
Product Features:
See More
Product Features:
- TPMS Snap-in stem for GM, Ford, Chrysler/Dodge/Jeep, Subaru
- 0.453″ rim hole compatibility
- 80 PSI maximum cold inflation pressure
McGard – Chrome Bulge Cone Seat Wheel Installation Kit for 5 Lug Vehicles (1/2"-20 Thread Size) (Part No.84550)
from
$104.99
The convenient way to order wheel locks and lug nuts. Contains all the hardware that you need to install 4 wheels and tires. McGard manufactures wheel locks and lug nuts in the USA to meet or exceed O.E.M. standards for safety and durability. Presently, McGard is an Original Equipment wheel lock supplier to most automobile brands around the world. These easy-to-use, one-piece wheel locks function like regular lug nuts, but require a special key tool for installation and removal. McGard lug nuts are guaranteed for life not to rust, chip or peel. Designed and built for the real world. Think about it: harsh elements, nasty corrosive wheel cleaners, overzealous impact guns, loose fitting lug wrenches and lead-foot drivers. This kind of treatment destroys ordinary lug nuts. McGard lug nuts can take the punishment and keep your wheels looking beautiful. This product may contain globally sourced materials/components.
Product Features:
See More
Product Features:
- User friendly key guides the key into the lock pattern for easy installation and removal.
- The computer generated key designs allow for an infinite number of key patterns.
- The extra narrow pattern groove on the lock resists the intrusion of removal tools into the pattern.
- Every McGard wheel lock and lug nut is fully machined from restricted chemistry steel made specifically for McGard and through-hardened for its unsurpassed level of security.
- McGard’s plating process includes several layers of nickel and one layer of microporous chrome producing a superior finish while protecting against rust.
- For use with steel or aluminum wheels with exposed decorative lug nuts that are tapered at the bottom.
- Set of 16 Lug Nuts, 4 Wheel Locks, 1 Key, & 1 Key Storage Pouch
McGard – Black Bulge Cone Seat Wheel Installation Kit for 5 Lug Vehicles (1/2"-20 Thread Size) (Part No.84551)
from
$134.99
The convenient way to order wheel locks and lug nuts. Contains all the hardware that you need to install 4 wheels and tires. McGard manufactures wheel locks and lug nuts in the USA to meet or exceed O.E.M. standards for safety and durability. Presently, McGard is an Original Equipment wheel lock supplier to most automobile brands around the world. These easy-to-use, one-piece wheel locks function like regular lug nuts, but require a special key tool for installation and removal. McGard lug nuts are guaranteed for life not to rust, chip or peel. Designed and built for the real world. Think about it: harsh elements, nasty corrosive wheel cleaners, overzealous impact guns, loose fitting lug wrenches and lead-foot drivers. This kind of treatment destroys ordinary lug nuts. McGard lug nuts can take the punishment and keep your wheels looking beautiful. This product may contain globally sourced materials/components.
Product Features:
See More
Product Features:
- User friendly key guides the key into the lock pattern for easy installation and removal.
- The computer generated key designs allow for an infinite number of key patterns.
- The extra narrow pattern groove on the lock resists the intrusion of removal tools into the pattern.
- Every McGard wheel lock and lug nut is fully machined from restricted chemistry steel made specifically for McGard and through-hardened for its unsurpassed level of security.
- McGard’s plating process includes several layers of nickel and one layer of microporous chrome with black PVD producing a superior finish while protecting against rust.
- For use with steel or aluminum wheels with exposed decorative lug nuts that are tapered at the bottom.
- Set of 16 Lug Nuts, 4 Wheel Locks, 1 Key, & 1 Key Storage Pouch
COAST TO COAST – 16 Inch, 5 Spoke, Gloss Black, Plastic, Set Of 4, Spring Steel Clip (Part No.IWC43116BLK)
from
$116.99
Coast to Coast International Wheel Covers are a quick and cost effective alternative to replacing factory OEM wheel covers that have been lost, stolen or worn over time. With a wide variety of designs and finishes, it is easy to find a style that is right for any vehicle. All Coast to Coast International products feature a limited lifetime warranty.
Product Features:
See More
Product Features:
- Designed And Manufactured To Fit Steel Wheels And Emulate OEM Designs
- Constructed From High-Quality, Durable, Automotive Grade ABS
- Two Layers Of Clear Coat Enhance And UV Protect The Finish
- A Cost Effective Alternative To Replace OEM Wheel Covers That Have Been Lost, Stolen Or Worn Over Time
- Installs In Minutes Without Tools
- Spring steel clip retention, Easier to install, better wheel retention
COAST TO COAST – Chrome Plated, Abs Plastic, Set Of 4 (Part No.IWCC2030)
from
$79.99
Coast to Coast International aftermarket center caps are a quick and cost effective alternative to replacing OEM center caps that have been lost, stolen or worn over time. With a wide variety of designs and finishes, it is easy to find a style that is right for any vehicle. All Coast to Coast International products feature a limited lifetime warranty.
Product Features:
See More
Product Features:
- Designed And Manufactured To Fit Directly Into The OEM Wheel
- Constructed From High-Quality, Durable, Automotive Grade ABS
- Two Layers Of Clear Coat Enhance And UV Protect The Finish
- A Cost Effective Alternative To Replace OEM Center Caps That Have Been Lost, Stolen Or Worn Over Time
- Installs In Minutes Without Tools And Stays Securely Attached Until Removed
COAST TO COAST – 18", 10 Spoke, Gloss Black, Plastic, Set Of 4, Not Compatible With Steel Wheels (Part No.IWCIMP407BLK)
from
$207.99
Quickly and easily change the trim level appearance of your car, pickup truck or SUV with Impostor(R) wheel skins from Coast to Coast International. Each Impostor(R) wheel skin is designed and manufactured from automotive grade ABS to fit securely over the OE wheel. Installation in simple and secure. Pair them with CCI Grille Overlays and Door Handle or Mirror Covers for a complete package look. All Coast to Coast International products feature a limited lifetime warranty.
Product Features:
See More
Product Features:
- A NEW LOOK FOR LESS: Upgrade The Trim Level Appearance Of Your Vehicle With These Wheel Skins. Add Handles And Mirror Covers (Sold Separately) For A Factory-Style Package
- Wheel Skins Are Year-Make-Model Specific And Available In Different Finishes
- FIT SECURELY OVER THE ORIGINAL WHEEL, Fits Like A Glove Over Existing Wheels And Stay Securely Attached Using A Patented Retention System So You Can Be Confident That They Wont Fall Off While Driving
- UV Protected Paint And A Clear Coat Ensure That The Finish Wont Crack Or Fade
- COMPLEMENTS OEM STYLING, Instantly, And Easily, Upgrades The Vehicle Aesthetics While Complementing The OEM Styling Of The Vehicle
- EASY TO INSTALL, No Tools Are Required For A Quick, Snap-On Installation That Is Ready To Go In Minutes And Easy To Maintain. Designed And Tested In The USA.
COAST TO COAST – Wheel Cover, Imposter Series, 16 Inch, 5 Flat Indented Spoke, Fits OE Wheel, Chrome Plated ABS, Set Of 4 (Part No.IWCIMP318X)
from
$129.99
CCI Impostor wheel skins are an easy and affordable way to upgrade the trim level appearance of your vehicle. Constructed of ABS plastic and avaiable in a variety of finishes, CCI Impostor wheel skins are simple to install and provide years of head turning style. Pair them with CCI grille overlays, mirror covers and door handle covers to complete the look.
Product Features:
See More
Product Features:
- Designed and manufactured for quality fitment and finish
- Easy to install, long lasting finish
- Manufactured with automotive grade ABS, Quality and durable product
- Emulates factory styling and enhances OEM design
- 27 hour CASS test, chrome plating tested to ensure quality and durability
- Spoke Retention, No wheel weight issues, quick installation
- Limited Lifetime Warranty
COAST TO COAST – 16 Inch, 7 Split Spoke, Silver Color, Plastic, Set Of 4, Spring Steel Clip (Part No.IWC18916S)
from
$77.99
Coast to Coast International Wheel Covers are a quick and cost effective alternative to replacing factory OEM wheel covers that have been lost, stolen or worn over time. With a wide variety of designs and finishes, it is easy to find a style that is right for any vehicle. All Coast to Coast International products feature a limited lifetime warranty.
Product Features:
See More
Product Features:
- Designed And Manufactured To Fit Steel Wheels And Emulate OEM Designs
- Constructed From High-Quality, Durable, Automotive Grade ABS
- Two Layers Of Clear Coat Enhance And UV Protect The Finish
- A Cost Effective Alternative To Replace OEM Wheel Covers That Have Been Lost, Stolen Or Worn Over Time
- Installs In Minutes Without Tools
- Spring steel clip retention, Easier to install, better wheel retention
COAST TO COAST – 18 Inch, 15 Spoke, Chrome Plated, Plastic, Set Of 4, Lug Covers (Part No.IWC47218C)
from
$167.99
Coast to Coast International Wheel Covers are a quick and cost effective alternative to replacing factory OEM wheel covers that have been lost, stolen or worn over time. With a wide variety of designs and finishes, it is easy to find a style that is right for any vehicle. All Coast to Coast International products feature a limited lifetime warranty.
Product Features:
See More
Product Features:
- Designed And Manufactured To Fit Steel Wheels And Emulate OEM Designs
- Constructed From High-Quality, Durable, Automotive Grade ABS
- Two Layers Of Clear Coat Enhance And UV Protect The Finish
- A Cost Effective Alternative To Replace OEM Wheel Covers That Have Been Lost, Stolen Or Worn Over Time
- Installs In Minutes Without Tools
- Lug cover retention, security of a bolt on, quicker to install
Dorman – Wheel Lug Nut Lock Set: M14-1.50 Thread, Conical 60, Acorn, 35.8 mm Length, Chrome, 5 Locks/1 Key (Part No.712-628.5)
from
$21.99
Prevent wheel theft with this attractive, precision-manufactured wheel lock set. Made of quality materials for durability, these parts have undergone try-on and corrosion resistance testing to ensure long service life. These sets come in different sizes, quantities and appearances, so check the product details to ensure you have the exact number, look and fit you need.
Product Features:
See More
Product Features:
- Replacement or upgrade – prevent theft with this wheel lock set, which replaces the factory wheel nuts with attractive, corrosion-resistant locking nuts
- Various options – sets come in different sizes, quantities, and appearances; check the product attributes to ensure you have exactly what you need for your vehicle
- Durable construction – made from quality materials to strict specifications and carefully tested to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Wheel Lug Nut Lock Set: 1/2-20 Thread, Conical 60, Acorn, 1.39" Length, Orange, 20 Locks/1 Key (Part No.711-255I)
from
$61.99
Prevent wheel theft with this attractive, precision-manufactured wheel lock set. Made of quality materials for durability, these parts have undergone try-on and corrosion resistance testing to ensure long service life. These sets come in different sizes, quantities and appearances, so check the product details to ensure you have the exact number, look and fit you need.
Product Features:
See More
Product Features:
- Replacement or upgrade – prevent theft with this wheel lock set, which replaces the factory wheel nuts with attractive, corrosion-resistant locking nuts
- Various options – sets come in different sizes, quantities, and appearances; check the product attributes to ensure you have exactly what you need for your vehicle
- Durable construction – made from quality materials to strict specifications and carefully tested to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Popular 2010 Chevrolet Impala Wheels and Tires Categories
2010 Chevrolet Impala Wheels and Tires
You count on your 2010 Chevrolet Impala to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Wheels and Tires. With 151 Wheels and Tires ranging in price from $2.29 to $7,321.99, you’re sure to find everything you need for your 2010 Chevrolet Impala.
Brands matter. If you want to shop a specific Wheels and Tires brand, we stock 18 different brands like Dorman, Autel, and Schrader. 2010 Chevrolet Impala Wheels and Tires start as low as $2.29!
One of the best ways to find top quality OEM or aftermarket Wheels and Tires is by asking professionals. Short of that, you can shop with confidence thanks to our 6,574 extensive product reviews on 2010 Chevrolet Impala Wheels and Tires. Some of the top-rated Wheels and Tires products we carry are Wheel Bearing and Hub Assembly: Front, Rear, 5 Studs, Metal clip with 4.3 stars and Hub & Bearing Assembly with 4.1 stars.
Did we mention you can order your Wheels and Tires from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Wheels and Tires inventory for your 2010 Chevrolet Impala below to get started!
Top-Rated Wheels and Tires Brands For Your 2010 Chevrolet Impala
Trusted Wheels and Tires OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2010 Chevrolet Impala running right for years to come. In our inventory you’ll find brands like Dorman, Autel, Schrader, and even more.
Popular Xtra Seal Wheels and Tires
You’ll find popular Xtra Seal brand products across TPMS Sensors. All are waiting to get your 2010 Chevrolet Impala back on the road. Some of the top-rated Xtra Seal products in these categories are:
Top-Rated Dorman Wheels and Tires
If Dorman are what you’re looking for, our inventory holds plenty. We stock Dorman brand Wheels and Tires for your 2010 Chevrolet Impala, and some of our most reviewed Dorman parts include:
from
$8.29
(59)
Wheel Lug Nut: M12-1.50 Thread, Conical 60, Acorn, 1.375 in Length, Chrome, 4 Pack
Wheel Lug Nuts
FAQs for 2010 Chevrolet Impala Wheels and Tires
What are the most purchased Wheels and Tires for the 2010 Chevrolet Impala?
Out of 151 Wheels and Tires for the 2010 Chevrolet Impala, the most popular in our inventory are:
from
$2.29
This product is not rated
Wheel Lug Nut: M12-1.50 Thread, Conical 60, Bulge Acorn, 1.382" Length, Chrome (Sold by each)
Wheel Lug Nuts
from
$2.79
This product is not rated
Wheel Lug Nut: M12-1.50 Thread, Conical 60, Bulge Open End, 0.831" Length, Chrome (Sold by each)
Wheel Lug Nuts
What are the top-rated 2010 Chevrolet Impala Wheels and Tires?
Top-rated Wheels and Tires for your 2010 Chevrolet Impala based on customer reviews/ratings are:
from
$161.99
(232)
Wheel Bearing and Hub Assembly: Front, Rear, 5 Studs, Metal clip
“Good quality, would buy again.”
from
$41.99
(70)
Programmable Tire Pressure Sensor (TPMS): Snap-In Rubber Valve, 1 Piece
“Was everything I expected”
