Name: Pinion Seal
Brand: Corteco
SKU: J7010481273CFW
Price: 12.58 USD

from

$12.58

Pinion Seal

from

$15.99

Boot kits protect a joint in the car that would be destroyed by dirt, sand and other particles if left exposed, even under normal conditions so it’s important that they be properly maintained and in good condition. Rein automotive application specific inner and outer axle boot kits come complete with everything needed to do a proper installation, including OE grease and all the hardware needed for a guaranteed fit the first time.

Product Features:

Comes with all the needed hardware for the complete repair; clamps, washers, clips, etc.
Comes with the OE grease
Boot manufactured with highest quality materials to prevent cracking, wear and leaking
Matches original equipment design specifications

from

$20.42

Differential Side Cover Seal, 90 x 44 x 10

from

$29.90

With Clamps and Grease The Vaico CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$16.08

Input Shaft Seal

from

$3.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$12.79

Product Features:

High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$36.99

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON®, GM DEXRON®-II and DEXRON®-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III , Toyota/Lexus Type T, T-III and T-IV , Honda/Acura ATF-Z1 (except in CVTs) , Mercedes Benz NAG1 , Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$198.64

FAG is a supplier of original equipment wheel bearings, hubs and seals to major automobile manufacturers and 1st/2nd tier suppliers throughout the world. All FAG wheel bearings are maintenance free and have been designed for the entire life of the vehicle. The FAG wheel hub assembly is a highly integrated unit with flanges for the brake disc, wheel and knuckle, which allow the highest possible running accuracy. Integrated speed encoders generate the signals required for steering the vehicle (ABS/ESP). The bearing clamping force is applied and controlled by FAG via an orbital formed shoulder.

Product Features:

Original Equipment Quality
Maintenance free
Premium modified bearing steel
Lubricated with specially developed greases
Optimized sealing systems

from

$152.56

FEBI manufactures OE quality wheel hub assemblies that provide superior performance and durability.

Product Features:

OE Quality
High quality steel and surface finishes
Proper implementation of heat treatment
Precise engineered hub surface provide maximum load capacity and durability

from

$94.99

Whiteline’s differential bushing solutions ensure pinion angles are maintained while delivering an improved gear shift resulting in reduced initial torque loss and greater power transfer to the wheels.

Product Features:

Featuring premium anodized alloy materials, Whiteline alloy products are anodized providing a long-lasting protective barrier to corrosion and wear but they look great too.
Protective plating on all metal components acts as a hard skin that is much tougher than conventional paint allowing this product to withstand the toughest conditions and resist corrosion for years to come.
Whiteline’s latest technology synthetic elastomer formulation boasts resistance to oil, grease, ozone and weathering.

from

$13.03

The Corteco Driveshaft Bushing is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$102.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$7.99

Rein Automotive OE quality oil drain plugs are made with premium materials and designed and manufactured to be direct-fit replacements. Rein oil drain plugs are designed to tight tolerances to ensure proper sealing.

Product Features:

Designed to tight tolerances to ensure proper sealing.
Rein Oil Drain Plugs are coated for high corrosion resistance.
Designed and constructed to strict engineering quality standards.
Includes copper sealing gasket.

from

$13.82

The Febi Axle Shaft Nut is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$12.32

The Febi Axle Shaft Nut is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$7.39

DIFFERENTIAL DRAIN P

from

$43.52

Rugged SKF drive shaft support bearings are built to meet or exceed OE specifications. The Support Bearings are also built on the years of experience that SKF has earned designing and supplying bearings to the world’s largest OE manufacturers. Engineered and manufactured to specific application requirements that deliver precise drive shaft alignment and support. Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination. Rubber support cushions are manufactured from durable rubber compounds that provide maximum support while isolating the driveline shaft from damaging vibration. Drive shaft support frames are constructed from high quality steel or aluminum that provides additional strength and long life in harsh environments.

Product Features:

Original equipment design and quality
Utilizes OE equivalent or better materials
Pre-Lubricated and reinforced seals
Rubber support cushions are manufactured from durable rubber compounds
Support frames are constructed from high quality steel or aluminum

from

$13.99

Drive Shaft-Ctr Support Bearng

from

$83.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to BMW 06-17;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 2006-2017
Weight approx: 1 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 0.45 INCH / 11 MM
MOUNT WIDTH: 6.30 INCH / 160 MM
STYLE: ROUND FRAME
WITH WINGS

from

$158.09

The Vaico Driveshaft Support with Bearing is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Made in Germany OE Quality
Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications Q+ The Seal of Excellence
ALWAYS OEM QUALITY
ALWAYS MADE IN GERMANY

from

$985.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$993.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$884.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$457.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$993.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$878.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability