from

$29.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$64.99

Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.

Product Features:

Matches OE form, fit and function
Manufactured with high quality materials
Designed for underhood conditions
Quality constructed for durability
Application specific for this vehicle

from

$1.73

Heater Pipe O-Ring

from

$11.99

Rein Automotive OE Quality expansion tank caps are designed to be direct replacements for OE caps. Rein caps are designed to match or exceed the OE materials used and are produced to the highest standards to ensure long service life. Rein Automotive OE quality expansion tank caps keep the coolant system at the proper pressure just like the OE cap.

Product Features:

Manufactured to strict engineering standards/specifications in materials and tolerances.
Direct fit.
Meets or exceeds pressure specifications demanded by the OE manufacturer.
Produced by an original equipment supplier.

from

$79.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$3.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$42.99

Rein Automotive OE quality expansion tanks, install, fit and perform the way the original manufacturer intended. These tanks are designed to match or exceed the OE materials used and are produced from virgin plastic with no regrind to prevent cracking from heat cycles and ensure the plastic is durable and will have a long service life.

Product Features:

Produced from virgin plastic meeting/exceeding OE specifications and ensuring long life
Resistant to cracking and wear from heat cycles preventing coolant loss
Direct fitment allows easy installation
Manufactured to strict engineering standards/specifications in materials and tolerances

from

$119.99

Rein Automotive OE quality coolant pipes fit European vehicles the way the original manufacturer intended. Designed to be a direct replacements for the OE coolant, Rein coolant pipes are identical to the OEM.

Product Features:

Designed as direct-fit replacements to ensure trouble-free proper installation.
Made to strict engineering quality standards.
Part is produced using only the highest quality materials.
Resistant to heat, salt, road debris, oil and other contaminants.

from

$28.49

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

Ideal for rigid cast aluminum parts
Meets OEM Specifications
Sensor safe & non-corrosive
Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
Blowout resistant, allowing leakproof gaskets to be made in just one minute
Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

from

$1.83

Water Temperature Sensor O-Ring

from

$88.27

The Graf Water Pump contains no remanufactured parts and is produced using an optimized all metal impeller design to assist in cooling under high RPM, and performance demands. Selection of raw materials, reliability of machinery and production processes, stringent controls throughout the production process, from melting to fitting, as well as reliability tests performed using equipment able to determine true performance, go to ensure this product is a real guarantee of safety and long life. The Graf water pump is centrifugal in type and comprises a bladed rotor linked by means of a shaft (which rotates on bearings housed in a support) to the drive gear; the seal between the pump and the motor block is guaranteed by a gasket, while the inside of the pump is guaranteed by a mechanical seal. Component parts: Impeller: supplies the fluid with the necessary energy to cover the entire cooling circuit. Mechanical seal: ensures fluid seal inside the pump. Bearing: transmits movement to the impeller and supports any ventilation parts. Entrainment part: for transmitting movement to the bearing. Pump body: supports the basic pump component parts and conveys the coolant in the motor block.

Product Features:

All the component parts fitted are pre-tested to evaluate durability, performance and reliability.
The bearings undergo a durability test equivalent to nominal lifespan and are then inspected to assess integrity.
The mechanical seals are tested in extreme coolant temperature conditions according to predefined cycles.
The shape of the impellers is optimized thanks to the use of prototypes on which flow and performance tests are performed.
On both the entrainment parts and the bodies, the choice of materials and/or technologies different to original ones is made on the basis of structural and mechanical tests.
After assembly all the pumps undergo seal tests on units that reject those with leaks above set limits.

from

$10.35

Water Pump Coupling

from

$259.99

This engine cooling fan assembly is precision-engineered to match the fit and performance of the stock radiator fan on specific vehicle years, makes and models. It has been rigorously tested to ensure it cools as effectively as the original part.

Product Features:

Ideal replacement – this engine cooling fan assembly was precision-engineered to match the fit and performance of the stock radiator fan assembly on specific vehicles
Complete package – assembly is designed with the same materials and components as the original part
Quality assured – motors are tested in laboratory settings to ensure performance
Cost effective and reliable – trustworthy manufacturing for far less than same part at the dealership

from

$0.86

Cooling Hose Flange Plug

from

$2.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$58.99

This replacement engine coolant thermostat housing is engineered to match the fit and durability of the stock thermostat housing on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

Ideal replacement – this engine coolant thermostat housing directly replaces the original housing on specified vehicle years, makes and models
Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housings

from

$26.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$156.27

Auxiliary Water Pump

from

$6.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$5.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$3.90

C Clip Retainer

from

$19.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute

from

$32.99

OEM specified. Designed specially for high-torque and high vibration applications, like those common in import engines, this premium RTV gasket maker exceeds manufacturers’ performance requirements. Sensor-safe, low odor, and non-corrosive. Maximum vibration resistance, with outstanding resistance to oils, cooling and shop fluids. Temperature range -65ºF to 500ºF (-54 Deg. C to 260 Deg. C) intermittent.

Product Features:

Designed specially for high-torque and high vibration applications
Maximum vibration resistance with outstanding resistance to oils, cooling and shop fluids
OEM specified
Low-odor, non-corrosive formula
Temperature Range: -65 Deg. F to 500 Deg. F (-54 Deg. C to 260 Deg. C)

from

$300.99

The gasket on certain Audi and VW OEM engine water pump housings swells when it comes in contact with oil, causing the plastic housing to crack. This Dorman OE FIX housing has been upgraded to aluminum to prevent cracking. In addition, the gasket material has been upgraded to reduce swelling when it comes in contact with oil for a longer service life. This housing is designed to match the fit and function of the original housing on specified applications, and is engineered for reliable performance and durability..

Product Features:

Improved design – this engine water pump housing has upgraded gasket material to reduce swelling when it comes in contact with oil for a longer service life.
Direct replacement – this engine water pump housing is designed to match the fit and function of the original housing on specific Audi and VW vehicles
Restores functionality – maintains the proper engine temperature, protecting the engine from damage caused by overheating
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$274.99

Demanded by today’s OEMs and manufactured to meet critical fit, form and function requirements, Dayco timing belt kits ensure parts accuracy, time savings and long-lasting performance. This kit is designed for the replacement of worn or damaged original equipment timing belts, tensioners and idler pulleys – each matched to a specific vehicle make and model.

Product Features:

Engineered for both domestic and import vehicle applications with a timing belt
All components needed for a complete timing belt replacement included in one box
Includes premium Dayco components and tough, wear-resistant belt