2009 Toyota FJ Cruiser Suspension Parts

The Air Command Standard Duty Dual Electric Air Compressor System Kit Allows You To Adjust Your Air Springs With The Touch Of A Button. It Offers A Built in Air Source For Your Suspension System, Making It Easy To Alter Your Springs To Align With The Load Type And Environment. When Shopping For Air Accessories, You will Find That Firestone Air Command Standard Duty Dual Electric Air Compressor System Kit Is Designed To Have A Couple Of Special Benefits. First, The Air Command Standard Duty Dual Electric Air Compressor System Kit Comes Ready To Install, So You Can Set It Up And Get Back To The Road where You Want To Be. Just Connect A Few Wires To The Compressor And A Few To Your Vehicle. The Air Lines And Wiring Harness Can Be Plugged Into The Same Side Of The Unit For Smoother Routing Of Lines And Power Supply. After The Air Command Standard Duty Dual Electric Air Compressor System Kit Is Properly Installed, You Can Make Pressure Adjustments By Pressing A Single Button. This Air Command Standard Duty Dual Electric Air Compressor System Kit Component Allows For Side To Side Or Front to rear Leveling, Real time Pressure Readout, And Dual Left And Right PSI And Pressure Control Readouts. The Air Command Standard Duty Dual Electric Air Compressor System Kit Easy to read Needle Gauge Can Be Viewed Day Or Night, Without Straining Or Squinting Your Eyes. Prior To Installing The Air Command Standard Duty Dual Electric Air Compressor System Kit, Review The Instructions And Identify All Of The Components To Help Make Sure You Get Maximum Performance From Both Your Air Springs And Air Command Standard Duty Dual Electric Air Compressor System Kit. The Installation Steps Are Different Depending On Whether You are Enhancing An Existing Air Helper Spring System With The Air Command Standard Duty Dual Electric Air Compressor System Kit Or Installing It With A New Air Spring System.

Product Features:

• Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
• Adjust The Ride For Various Load And Road Conditions With A Switch, Remote Or Mobile App
• Provides An Instant Air Source For The Air Helper Springs Or Accessories
• Dual Point Fill (Both Air Springs Fill Independently Of Each Other)
• Light Duty Compressor Specs (120 PSI Max Air Pressure, 9 Percent Duty Cycle, 0.32 CFM)

Timbren suspension enhancement system – The decision is easy, Timbren suspension kits (SES kits) are designed to enhance the suspension of your vehicle. Improve load handling haul heavy loads with ease eliminate sag and sway.

Product Features:

• Eliminate Suspension Sag: When Towing A Heavy Trailer, Timbren SES Extends The Life Of The Suspension Of Your Vehicle And Helps To Avoid Bottoming Out
• Control Trailer Sway, A Condition Which Occurs With Unbalanced Loads, In Crosswinds Or When Passing Heavy Trucks Timbren SES Stabilizes Your Vehicle
• Control Body Roll, During Cornering With Powerful Progressive Rate Rubber Springs Which Resist Lean And Enhance Vehicle Stability
• Improve The Ride, By Allowing The Aeon(R) Rubber Springs Absorb Road Shocks And Bumps. Towing A Trailer Doesnt Have To Mean Poor Ride Quality
• Economical And Trouble Free
• Simple And Easy To Install

aFe Control introduces these Sway-A-Way High Performance replacement Coilovers for the 2005-2020 Toyota Tacoma. These 2.5″ diameter Coilovers feature all the same race winning engineering and components that have 20+ years of testing into a specifically designed kit that will bolt directly into your daily driven vehicle. This kit offers adjustable ride height and better off road damping curves without sacrificing any on road comfort or handling. These front Coilovers are 100% designed and built in the USA that feature bright zinc plated steel cylinder bodies and CNC machined aluminum components. The kit comes pre-set for 2″-2.5″ of lift.  Also included is  a spanner wrench for you to adjust your ride height to find your perfect blend of performance and style. This package is designed as a direct fit application and requires no modifications to the vehicle.

Product Features:

• CNC Machined Components Made To The Strictest Tolerances
• Polished Nitro Steel Shaft for Strength And Durability
• Teflon Lined Steel Spherical Bearings
• Multi-Seal Carrier To Ensure Zero Leakage

These Rear Coil Springs provide 1″-2″ of lift. This kit is designed as a direct fit application and requires no modifications to the vehicle.

Product Features:

• Direct Fit Installation, Requires No Modifications
• 1″-2″ Lift

This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.

Product Features:

• Meets or exceeds OE requirements
• Helps restore steering and handling

KYB Strut Mounts eliminate the vibration and noise caused by old, hardened vibration insulators. They optimize suspension performance by offering OE quality replacement components designed for each application. KYB Strut Mounts cushion the impacts from road bumps to reduce the jarring effect, noise and vibration that old mounts transmit into the vehicle. Front bearing plates are the steering pivots and support vehicle weight. They are critical to steering performance and wheel alignment. KYB Strut Mounts and bearing plates have a reputation for providing the highest quality in the industry.

Product Features:

• The highest quality replacement strut mount available
• Optimizes suspension performance by offering Original Equipment quality replacement components designed for each application
• Superior rubber reduces noise, vibration and harshness
• Mount bearings provide smoother steering and help retain front end alignment
• Matched grade studs and nuts

aFe Control introduces these Sway-A-Way High Performance replacement shock absorbers for the 2003-2020 Toyota 4Runner and 10-14 FJ Cruiser. These 2.0″ diameter shocks feature all the same race winning engineering and components that have 20+ years of testing into a specifically designed kit that will bolt directly into your daily driven vehicle. This kit offers adjustable ride height and better off road damping curves without sacrificing any on road comfort or handling. These rear shocks are 100% designed and built in the USA that feature bright zinc plated steel cylinder bodies and CNC machined aluminum components. Also included are rear coil springs that provide 1″-2″ of lift. This package is designed as a direct fit application and requires no modifications to the vehicle.

Product Features:

• CNC Machined Components Made To The Strictest Tolerances
• Direct Fit Installation
• Coil Springs Included for an Additional 1-2″ of Lift
• 2 Year Limited Warranty

aFe Control introduces these Sway-A-Way High Performance replacement shock absorbers for the 2003-2020 Toyota 4Runner and 10-14 FJ Cruiser. These 2.0″ diameter shocks feature all the same race winning engineering and components that have 20+ years of testing into a specifically designed kit that will bolt directly into your daily driven vehicle. This kit offers adjustable ride height and better off road damping curves without sacrificing any on road comfort or handling. These rear shocks are 100% designed and built in the USA that feature bright zinc plated steel cylinder bodies and CNC machined aluminum components. This package is designed as a direct fit application and requires no modifications to the vehicle.

Product Features:

• CNC Machined Components Made To The Strictest Tolerances
• Polished Nitro Steel Shaft for Strength And Durability
• Teflon Lined Steel Spherical Bearings
• Multi-Seal Carrier To Ensure Zero Leakage

Made of superior Hyper-Flex material. Saves replacing again and again, lasting 3 to 10 times longer. Assemble to chassis the same way as OEM isolators and do not adversely change ride characteristics.

Product Features:

• Made of Superior Hyper-Flex+ Material
• Lasts from 3 to 10 Times Longer
• Assemble to Chassis Same Way as OEM
• Maintains Factory Ride Characteristics
• Simple Way to Increase Vehicle Height

Monroe® Shock-Mate® Shock Absorber Boot Kits are universal replacement shock boots use to protect the shock’s piston rod from dirt, mud and other contaminants – protecting the life of your shocks.

Product Features:

• Protects the shock’s piston rod from damage
• Universal design for easy installation
• Tie-strap included for a secure fit
• Constructed from high quality urethane for maximum durability
• Multiple color choices available

Designed to restore a vehicle’s original factory drivability and performance, Monroe® OESpectrum® light truck shock absorbers provide an exceptional level of handling precision and control while filtering out noise, vibration and harshness.

Product Features:

• EXCEPTIONAL HANDLING — Full displaced valving, tuned specifically to each vehicle, adjusts to road extremes while the larger bore provides more efficient damping control to provide consistency and a smooth ride
• IMPROVES STABILITY — ASD (Acceleration Sensitive Damping) valving technology and fluon-banded piston deliver greater control and handling while improving ride comfort
• IMPROVES PERFORMANCE — Nitrogen gas-charge maintains tire-to-road contact for improved ride and handling by reducing aeration and shock fade
• CONSISTENT RIDE — OE all-weather fluid contains special additives to assist with extreme temperatures and help reduce oil breakdown
• BUILT TO LAST — Self-lubricating fluid seal retains gas and reduces excessive friction against the piston rod to help reduce premature wear
• Special Seal: ‘Self-lubricating’ fluid seal designed to retain gas without excessive wear or friction.
• 1-3/8 inch (34.9 mm) bore (On most applications)
• 5/8-inch (15.9 mm) diameter piston rod (On most applications)

KYB Strut Mounts eliminate the vibration and noise caused by old, hardened vibration insulators. They optimize suspension performance by offering OE quality replacement components designed for each application. KYB Strut Mounts cushion the impacts from road bumps to reduce the jarring effect, noise and vibration that old mounts transmit into the vehicle. Front bearing plates are the steering pivots and support vehicle weight. They are critical to steering performance and wheel alignment. KYB Strut Mounts and bearing plates have a reputation for providing the highest quality in the industry.

Product Features:

• The Highest Quality Replacement Strut Mount Available
• Optimizes Suspension Performance By Offering Original Equipment Quality Replacement Components Designed For Each Application
• Superior Rubber Reduces Noise, Vibration And Harshness
• Mount Bearings Provide Smoother Steering And Help Retain Front End Alignment
• Matched Grade Studs And Nuts

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• 100% Load tested
• Easy to install
• Provides like-new steering
• Designed to lower stresses for longer service life
• Worn or sagging coil springs can cause premature tire wear due to vehicle misalignment

Level out the front of your Toyota® Tacoma truck or 4Runner SUV by 2.25-in. with the LEVEL IT system from Rancho®. This leveling system features sway bar spacers and Rancho RS9000®XL struts for superior on-road comfort and off-road performance.

Product Features:

• COMPATIBILITY — Designed for Toyota Tacoma trucks and 4Runner SUVs
• LEVELED STANCE — Reduces factory rake and levels out truck’s stance by 2.25-in. (aftermarket bumpers, winches, etc. affect lift height)
• COMPLETE SOLUTION — Kit includes two sway bar spacers, two Rancho RS9000®XL struts (coil springs not included) and mounting hardware to accommodate tires up to 33-in. (must use OE springs and top mounting components)
• DELIVERS SUPERIOR PERFORMANCE — Rancho RS9000®XL struts with nine-position damping control for superior on-road comfort and off-road performance
• ENHANCED CONTROL — Sway bar spacers correct end link angles for roll and sway control
• EASY TO INSTALL — Bolt-on installation for an easy upgrade
• COMPLETE PERFORMANCE UPGRADE FOR TACOMA– Transform your suspension with Rancho RS9000®XL rear shocks (RS999319), performance upper control arms (RS64901) and rear block kit (RS70901), all sold separately
• COMPLETE PERFORMANCE UPGRADE FOR 4RUNNER — Transform your suspension with Rancho RS9000®XL rear shocks (RS999305), performance upper control arms (RS64903) and rear block kit (RS70080), all sold separately
• NOTES — Allows the use of OE wheels/tires, must use OE springs and top mounting components, trimming required for 33-in. wheel/tire (tire size varies between manufacturers)

Monroe® Shock-Mate® Shock Absorber Boot Kits are universal replacement shock boots use to protect the shock’s piston rod from dirt, mud and other contaminants – protecting the life of your shocks.

Product Features:

• Protects the shock’s piston rod from damage
• Universal design for easy installation
• Tie-strap included for a secure fit
• Constructed from high quality urethane for maximum durability
• Multiple color choices available

This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.

Product Features:

• Reduces vibration
• Torsional rubber bushings
• UV resistant
• No Squeak

Belltech has developed the solution to correct the lackluster handling and performance of today factory strut equipped trucks and Suv, utilizing the next generation valving technology of our new Trail Performance Shock line. In true Belltech style, combining our new leveling strut spacers with both front and rear Trail Performance shock absorbers you receive a complete solution to level your stance and rejuvenate those worn out OEM shocks and struts.

Product Features:

• Safe/Economical Solution
• Direct Bolt-In, No Additional Modifications
• Allows For Installation Of Larger More Aggressive Wheel/Tire Combo
• Easy To Install

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• 100% Load tested
• Easy to install
• Provides like-new steering
• Designed to lower stresses for longer service life
• Worn or sagging coil springs can cause premature tire wear due to vehicle misalignment

Complete Strut Assem

Corroded, stripped or broken control arm bolt making suspension repair difficult. This new control arm bolt matches the fit and function of the original bolt, its hardened steel construction allowing for secure installation of the control arm.

Product Features:

• Ideal replacement – this control arm bolt is a direct replacement for a corroded, stripped or broken original equipment control arm bolt
• Durable construction – made of hardened steel to match the function and durability of the original part
• Cost-effective solution – offers original equipment quality at a competitive price
• Quality tested – this part has undergone material testing and validation to ensure proper fit and long service life

POWER STEERING FLUID

Advanced Suspension Technology bushings offer a unique polyurethane alternative to conventional rubber suspension bushings. AST bushings are urethane-based and are impregnated with graphite to aid in lubrication and reduce noise. Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability. Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install.

Product Features:

• Unique polyurethane alternative
• Sleeves in the bushings freely rotate which enhances longevity
• Impregnated with graphite to aid in lubrication and reduce noise
• Alternative to conventional rubber suspension bushings

This suspension control arm is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles.

Product Features:

• Direct replacement – fits and performs like the original equipment on specific vehicles
• Reliable fit – precision-engineered to match the design and dimensions of original components
• Durable construction – manufactured to strict standards using sturdy, safe materials
• Rigorously tested – thorough quality control measures ensure longevity

Quick Strut Kit

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• Long-lasting performance
• Restores like-new steering and handling
• Engineered to meet or exceed OE requirements
• Construction and design validated by MOOG engineers
• Incorporates proven design and engineering features
• Wrench flats at base of stud allow for positive hold and use of sockets for quick and easy installation and removal

The ISG shock bushing is OE Quality and is manufactured using only the highest quality materials and is designed to reduce noise and vibration.

Product Features:

• OE-Equivalent and direct fit application
• Reduces squeaks, rattles, and vibration noise
• Resistant to oil and other contaminants
• Meets or exceeds OEM specifications

Designed to provide inflation control of your air helper springs. This kit will be an asset to your vehicle, meeting nearly all of your air supply needs.

Product Features:

• Individual Air Accessory Components Are Also Available, Including Compressors, Air Tanks, And Mounting Solutions, Providing A Wide Variety Of Air Control Assist Solutions
• Provides An Instant Air Source For The Air Helper Springs Or Accessories
• Dual Point Fill (Both Air Springs Fill Independently Of Each Other)

While your vehicle trusts Firestone Ride-Rite (TM) air helper springs to deliver on-the-road control, confidence, and comfort, you trust Firestone Air Command (TM) products to take your experience to the next level. You look to air accessories like the Xtreme Air Cmd-S Compressor System. With the Xtreme Air Cmd-S Compressor System, you can easily modify your air spring inflation by pressing a button. It equips your vehicle suspension system with an instant air source, making it easy to modify your springs to fit the road conditions and load type. You’ll find that the Firestone Xtreme Air Cmd-S Compressor System features some very user-friendly advantages. Unpackage the Xtreme Air Cmd-S Compressor System and enjoy an easy installation, so you can get it set up and be back on the move. Connect one wire to the compressor and three to the vehicle. The wiring harness and air lines can be plugged into the same side of the unit for cleaner routing of power supply and lines.

Product Features:

• Controls Two Air Springs Simultaneously
• Adjust The Ride For Various Load And Road Conditions With A Switch, Remote Or Mobile App
• Provides An Instant Air Source For The Air Helper Springs Or Accessories
• Single Point Fill (Both Air Springs Fill To The Same Pressure)
• Extreme Duty Compressor Specs (150 Pounds Per Square Inch Max Air Pressure, 100 Percent Duty Cycle, 0.94 CFM)