from

$7.99

Differential Cover B

from

$92.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 04-12; GMC 04-12; ISUZU 06-08;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 2004-2012
Weight approx: 3 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 4.00 INCH / 102 MM
MOUNT WIDTH: 3.75 INCH / 95 MM
STYLE: ROUND FRAME
WITH ELEVATED MOUNTING PLATFORM

from

$207.99

10 Bolt open spider gear set for ’00-’06 8.6″ GM with 30 spline axles. Fits case with one large window and one small window. A new carrier case will be needed for ’99 vehicles in order to use this spider gear set. This spider gear set fits casting number 7875 & 1073.

Product Features:

Spider gear kit
Fits 2000-2006 GM 8.6″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$361.99

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$50.99

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$12.29

This transfer case adapter seal matches the fit and function of worn or damaged original equipment part. This seal should be replaced as part any service that requires the transfer case and transmission to be separated.

Product Features:

Ideal replacement – this transfer case adapter O-ring is a direct replacement for a worn or damaged original equipment seal between the transfer case and transmission
Convenient on-hand part – this seal should be replaced whenever the transfer case is removed for service
Application-specific design – this O-ring has been designed of durable materials specifically for this vehicle application
Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

from

$127.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$93.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$231.99

This Motive Gear Differential Rebuild Kit includes all of the parts required to rebuild your stock open differential. The gears are lapped for quiet operation. Includes spider and side gears, cross shaft, lock pin or bolt and thrust washers.

Product Features:

GM8.6″ INTERNAL KIT (OPEN) 30 SPL. MID 2000-2008

from

$44.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$31.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2008 and down GM 8.6″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$18.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$88.06

SKF is a supplier of original equipment wheel bearings, hubs and seals to most of the world’s leading automakers. Engineered and manufactured to the highest quality standards, SKF wheel bearings greatly reduce friction and increase load-carrying capabilities. With an ability to boost reliability under heavy loads and misaligned conditions, SKF wheel bearings offer an ideal solution for many wheel end applications.

Product Features:

Precision bearing pre-load and correct application of advanced manufacturing techniques such as orbital rolling
100% tested to the actual OE specifications per part number for fit, form and function
High quality steel and surface finishes
Proper implementation of heat treatment

from

$8.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 354, 369 & 437G
Contains two 1.59″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$28.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$12.29

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$39.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$57.99

Cross pin shaft for 7.5″, 7.625″, and 8″ GM.

Product Features:

Cross pin shaft for GM 7.5″, 7.625″ and 8.0″
Fits standard open differentials only

from

$481.99

GM 8.6″ 30 spline standard open loaded carrier. Complete differential case with internals.

Product Features:

Standard open carrier case and spiders
Fits GM 8.6″

from

$28.99

7.6″ IFS GM side seals.Yukon Mighty seal.

Product Features:

Inner axle seal
Fits GM 7.6″ IFS

from

$354.99

Yukon forged yoke for GM 8.5″ with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Forged steel

from

$38.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$14.99

Product Features:

c-clip for GM 7.5″, 7.625″ and 8.0″

from

$404.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Carbon fiber clutches

from

$6.49

This drive axle shaft lock C-clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features: