from

$176.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$373.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Composite clutches

from

$201.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 2009 and down Ford 8.8″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$10.49

Product Features:

SOLID SPACER FORD 8.8″ & 9″

from

$59.99

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Ford 8.8″ with 7/8″ cross pin diameter
Works with Spartan Locker or standard open spider gears

from

$96.99

Product Features:

FRD 8.8″ INT. KIT 31 SPL OPEN 1987 & LATER ONLY

from

$48.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles.
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged.
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles.
Quality materials – all components are built for reliable longevity and performance.
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$649.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Ford 8.8″ with 31 spline axles and 7/8″ cross pin shaft
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$108.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG.&SEAL FORD 8.8

from

$101.99

Product Features:

MINI SPOOL 8.8 FORD 31SPL

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$235.99

Product Features:

FRD 10BL 8.8 R/P 3.27 MG

from

$12.99

8.8″ Ford cover gasket.

Product Features:

Cover gasket
Fits Ford 8.8″

from

$15.29

CUP

from

$35.99

Product Features:

MINI INSTALL KIT FORD 8.8

from

$30.99

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Ford 7.5″, 8.8″, 9″ and 10.25″

from

$363.99

Yukon spider gear kit for Ford 8.8″, 31 spline, Trac Loc posi. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects. This kit does not include cross pin shaft or clutches.

Product Features:

Spider gear kit
Fit Ford 8.8″ Trac Loc positraction with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$175.99

Product Features:

Fits 2003 and up Crown Victoria, Grand Marquis, Marauder and Town Car
28 spline
34 3/8″ long
5 lug
This axle is not compatible with ABS applications

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$404.99

Product Features:

Standard open carrier case and spiders
Fits Ford 8.8″ with 31 spline axles

from

$34.99

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

Forged From Premium Grade 8740 Chrome Moly Steel
Heat Treated
Nominally Rated At 200,000 Psi Tensile Strength
Specially Hardened, Precision Ground Washers
0.75″ Underhead Length
200,000 PSI
Sold As A Set

from

$1514.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$1489.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio