from

$55.99

Differential Pinion

from

$7.99

DiffRingGearBolt

from

$53.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Toyota 8″ and 4 cylinder engine, 1986 and up with OEM ring and pinion set
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$429.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket. This kit fits applications with a 29 spline pinion.

Product Features:

Fits Toyota V6 rear
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve eliminator, oil baffles and slingers, thread locker, marking compound and brush.

from

$78.99

Product Features:

Seal housing for Toyota 8″ and V6
Includes o-rings

from

$18.99

Product Features:

Bulkhead quit connect fitting

from

$298.99

Product Features:

Cross pin shaft
Fits Toyota V6

from

$11.99

Toyota 8″ & V6 gasket.

Product Features:

Dropout gasket
Fits Toyota 8″ and V6

from

$428.32

Differential Shift A

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$109.99

Yukon 12 hole yoke for ’83 and newer Toyota 8″ and V6 with 27 splines. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota 8″ and V6
27 spline
Round companion flange

from

$549.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 8″ and V6
Made from 9310 steel for added strength
Works with stock side gears in standard carrier case

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits standard rotation Toyota 7.5″ with 4 cylinder engine
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$16.99

Toyota 8″ & V6 pinion nut washer.

Product Features:

Pinion nut for Toyota 8″ and V6

from

$794.99

V6 standard Open case, bare.

Product Features:

Standard open carrier case
Does not include spider gears
Fits Toyota V6

from

$7.99

Oil baffle for Toyota Landcruiser reverse rotation front, 8″ IFS front & TV6/Tacoma rear with factory locker.

Product Features:

Oil baffle
Fits Toyota Landcruiser reverse rotation front

from

$16.99

ZIP locker switch.

Product Features:

Switch

from

$101.99

7.5″ V6 & 4cyl side shim kit (incl. 7 shims).

Product Features:

Carrier shim kit
Fits Toyota 7.5″

from

$867.99

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install..

Product Features:

Easier installation – this loaded axle assembly includes a new axle shaft, wheel bearing, hub and backing plate pre-assembled and ready to install right out of the box.
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components
Simpler solution – eliminates the need to use potentially dangerous shop press to perform complete bearing repair
Quality tested – this part has undergone try-on, corrosion and material testing to ensure a quality fit and long service life

from

$9.79

Product Features:

CRUSH SLEEVE TOYOTA TURBO V6, 86-93 REAR

from

$8.29

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$34.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft