from

$41.99

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

from

$65.39

ACM is a supplier of Original Equipment quality climate control products. 3 pin connector

from

$37.99

New Standard Replacement A/C Receiver Drier

Product Features:

Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$42.99

Rein air conditioning receiver/drier units are manufactured with premium OE quality materials designed to withstand the demands of automotive air conditioning systems. Rein air conditioning receiver/drier units are designed to prevent factors that cause premature failure in automotive air conditioning systems.

Product Features:

Rein air conditioning receiver/drier units are manufactured with premium OE quality materials which offer maximum protection from premature failures.
Rein air conditioning receiver/drier units are designed as direct-fit replacements to ensure trouble-free proper installation.
Rein air conditioning receiver/drier units come complete with hardware when necessary for installation to save installation time and additional costs.
Replace receiver/drier units when faulty or when a compressor fails. compressor failures may lead to contamination of receiver/drier units and replacement is recommended to prevent future issues.

from

$22.99

New Standard Replacement A/C System Seal Kit, MT2632, V6 Engine

Product Features:

MT2632, V6 Engine
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$39.99

Carquest Expansion Valves are designed to regulate the flow of refrigerant through the air conditioning system to provide optimal cooling to the passenger compartment. Each expansion valve is manufactured to original equipment specifications to perform its function even in the harshest climates. Each part is supplied with the necessary gaskets and o-rings for installation.

Product Features:

The bodies of these expansion valves are machined from a single block of aluminum or brass metal.
Each expansion valve has settings for tonnage and superheat based on the vehicle specifications.
Each expansion valve is tested for function and leakage according to OEM specifications to ensure optimal performance of the air conditioning system.
O-Rings necessary for installation are included.
O-Rings necessary for installation are included.

from

$73.43

The Rein A/C Expansion Valve is designed to the meet the exact OE specifications for quality, fit and performance.

Product Features:

OE-Equivalent and Direct fit Application
Pressure tested before leaving the factory, guaranteeing performance and function
Designed to the exact OEM specifications Installation Note: Receiver driers or accumulators, and expansion devices should be replaced any time an A/C system is opened. Individual A/C component warranties may be void if these items are not replaced.

from

$57.72

The ACM A/C Expansion Valve that is manufactured to exact OEM specifications for quality fit and performance.

Product Features:

OE-Equivalent and Direct fit Application.
Meet or exceed OEM specifications.
Utilizes the factory style fittings and connectors
Compatible with R12 and R134a refrigerant. Installation Note: Receiver driers or accumulators, and expansion devices should be replaced any time an A/C system is opened. Individual A/C component warranties may be void if these items are not replaced.

from

$137.99

Advance Auto Parts is committed to providing high-quality ABS sensors. The entire manufacturing process is closely managed to deliver high quality products.

Product Features:

High grade materials that are equal to or better than OE provide durability and long service life
All ABS sensors are tested for proper fit, form, and function
Wire diameter and sheathing same or larger than OE to ensure product quality
Glass filled reinforced plastic for superior resistance to automotive fluids, dirt, salt and road debris
Includes all necessary brackets and hardware

from

$242.99

Advance Auto Parts is committed to providing high-quality ABS sensors. The entire manufacturing process is closely managed to deliver high quality products.

Product Features:

High grade materials that are equal to or better than OE provide durability and long service life
All ABS sensors are tested for proper fit, form, and function
Wire diameter and sheathing same or larger than OE to ensure product quality
Glass filled reinforced plastic for superior resistance to automotive fluids, dirt, salt and road debris
Includes all necessary brackets and hardware

from

$86.81

The Huco OE quality ABS speed sensor is engineered to the exact specifications of the vehicle manufacturer to ensure the replacement sensor is the same in quality and function as the part installed as original equipment.

Product Features:

OE quality direct fit application
Manufactured to meet or exceed OE requirements and testing
Ground-isolated design with two-wire shielded harness helps protect the sensor signal from electro-magnetic interference

from

$9.99

New Standard Replacement A/C Service Cap And Valve Kit, MT2909

Product Features:

MT2909
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$19.99

All the seals needed to complete the job; Compatible with both R134a And R12 refrigerants; Application specific; SUV And rear air applications

from

$3.55

A/C Valve Core

from

$329.99

The Carquest condenser is an integral component of the motor vehicle air conditioning system. This part condenses the refrigerant into a liquid to prepare it for entry into the compressor. The condenser is manufactured according to OEM design specifications to ensure a long life with quality performance. Exact design standards produce a seamless fit into the engine compartment.

Product Features:

This is a parallel flow condenser that contains small micro-channels. It is highly recommended that this condenser be replaced if a failure has occurred in the vehicle’s air conditioning system that has resulted in debris contaminating the system. This
This Carquest condenser has a drier attached to it with an interior desiccant bag which will provide optimal moisture removal in the a/c system to maximize cooling performance.
The Carquest condenser production process includes quality driven details such as using zinc-coated tubes and electrostatic paint spray at high temperatures to provide the best corrosion resistance and durability in our condensers.
Continuous molds, laser welding machines, semi-automatic assembly stations and other advanced equipment provide quality products.
Each condenser uses only the highest quality raw materials including pure aluminum (not substandard or recycled) to provide the highest quality standards from beginning to finished product.
All brackets are designed per OEM specifications to ensure strength and reduce vibration and movement.
We leak test 100% of our condensers in helium leak test chambers to ensure the product does not leak.
Our condensers are manufactured from rigid design standards to fit OEM dimensions.
Each condenser design endures a series of tests that includes performance testing, vibration testing, blast testing, and salt spray testing to simulate real world conditions.
Each Carquest condenser is packaged using superior box construction. This box is easy to open and seal. Each condenser is packaged in the box with internal protection to keep the part centered and away from the package edges. The package passes the fre
All brackets are designed per OEM specifications to ensure strength and reduce vibration and movement.
We leak test 100% of our condensers in helium leak test chambers to ensure the product does not leak. This industry leading process is the most precise method and can detect even the smallest leak. The leak-free condenser is then charged with nitrogen a
Our condensers are manufactured from rigid design standards to match OEM dimensions. Each design undergoes a drop fit into the actual vehicle to ensure the final manufactured product provides an easy installation.
Each condenser design endures a series of tests that includes performance testing, vibration testing, blast testing, and salt spray testing to simulate real world conditions.
vibration testing
blast testing
and salt spray testing to simulate real world conditions.

from

$124.99

New Platinum Pro A/C Condenser

Product Features:

Made Of Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$157.99

New Platinum Pro A/C Condenser, GL And M Class

Product Features:

GL And M Class, Made Of Aluminum
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$39.99

Carquest Hose Assemblies are designed to carry refrigerant in an air conditioning system. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

100% of hose assemblies use Goodyear hoses that meet original equipment specifications for wall thickness and permeation.
Tubes and mufflers are designed to meet original equipment specifications for wall thickness.
Fittings are designed to couple and seal to eliminate leaks. Trivalent plating is used on steel fittings to enhance corrosion resistance. The fittings conform to original equipment specifications to allow for the proper fit with related air conditioning
Welds and crimps meet and exceed original equipment tension specifications.
Manufactured to allow flexibility in the hose to conform to engine compartments.
O-Rings necessary for installation are included.

from

$174.99

Rein OE Quality Air Conditioning Evaporator. Pressure tested before leaving the factory. Designed according to OE specifications, ensuring fit and function are identical to the original evaporator.

from

$192.33

A/C Evaporator

from

$101.99

Carquest Evaporators are designed to remove heat from the air inside the passenger compartment of a vehicle resulting in cooler air temperatures. They are manufactured to meet or exceed original equipment specifications and are designed to easily fit into the engine compartment.

Product Features:

The design and manufacture of the evaporators result in uniform refrigerant distribution with optimal flow for improved performance and maximum heat transfer.
The evaporators are constructed to offer a lightweight, compact design that will fit easily within the engine compartment.
The surface treatment on each part ensures optimum water drainage to prevent mold and odors in the system.
The evaporators are 100% tested to meet or exceed original equipment specifications. Each part is helium tested to ensure no leaks.
O-Rings and gaskets necessary for installation are included.