2008 Ford E-450 Super Duty Differentials

Find your specific 2008 Ford E-450 Super Duty original or aftermarket Differentials below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.

Essential 2008 Ford E-450 Super Duty Differentials

from

$184.99

Product Features:

D70 HD BEARING SEAL & GASKET M/K

from

$6.99

Ring Gear bolt for Ford 10.25″ & 10.5″. 1/2″ x 20.

Product Features:

Ring gear bolt for Ford 10.25″ and 10.5″
1/2″ x 20 thread

from

$194.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 60
Includes carrier bearings and races and carrier shim kit

from

$7.99

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

Power Lok case bolt for Dana Spicer 60 and 70
7/16 x 14 thread
3.5″ long
9/16″ hex head

from

$344.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 80 with 4.375″ O.D. pinion bearing
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$1175.00

Differential

from

$13.99

Product Features:

Cover gasket
Fits Dana Spicer 60, 70, 70U and 70HD

from

$16.99

ZIP locker switch.

Product Features:

Switch

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$10.99

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
7/8″ x 20 thread
1 1/8″ socket

from

$318.99

Product Features:

Spider gear kit
Fits Dana Spicer 80, 37 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$7.99

Product Features:

Oil baffle
Fits Dana Spicer 70 and 70HD

from

$16.99

Product Features:

Brand may vary by location

from

$494.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 1999-2006 Ford 10.5″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$53.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.99

Product Features:

Pinion nut washer
Fits Dana Spicer 80

from

$53.99

Conversioon spacer to use 10.25″ ring & pinion in ’08 & up 10.5″ housing.

Product Features:

Conversion spacer
Used to install Ford 10.25″ ring and pinion set into 2008-2010 Ford 10.5″ housing

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$156.99

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

Cross pin shaft
Fits Dana Spicer 60 and 70
Powr Lok positraction only

from

$4.99

Product Features:

Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
Fits standard open differentials only

from

$7.99

Dana 70 & Dana 80 pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer for Dana Spicer 70 and 80

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$15.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$467.99

Yukon 1541H alloy left Hand replacement rear axle for Dana 70 with a length of 43 inches and 35 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full float axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
43.0″ long
Fits Dana Spicer 70 in 1996-2000 Ford E350
Right hand side

from

$18.99

Product Features:

CARRIER SHIM-DANA 60 & 70

from

$269.99

Dana 60 & Dana 61 TracLoc clutch set.

Product Features:

Clutch kit
Fit Dana Spicer 60 Trac Loc positraction

from

$209.99

Extra large clamshells for use with Dana 70HD, Dana 80, AAM 11.5″, Ford 9.75″, Ford 10.25″ & Ford 10.5″.

Product Features:

Extra Large clamshell
Fits carrier bearing puller

from

$1487.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

Fits Ford 10.25″ and 10.5″
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

Popular 2008 Ford E-450 Super Duty Differentials Categories

Differential Oil

Rear Differential Cover Gaskets

Differential Covers

Differential Pinion Shaft Lock Bolts

Differential Bearings

Differential Axle Shafts

Differential Pinion Pilot Bearings

Differential Cover Bolts

Differential Carriers

Differential Bearing Kits

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Clutch Packs

Differential Ring and Pinions

Differential End Yokes

Differential Lock Assemblies

Differential Air System Seal Housings

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Front Differential Cover Gaskets

Differential Pinion Bearing Kits

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Differential Carrier Bearing Shims

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Differential Pinion Gear Washers

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Differential Clutch Pack Clips

Differential Conversion Spacers

Maybe you’re in the middle of a full rebuild of that 2008 Ford E-450 Super Duty. Maybe you just need a couple of Differentials. Either way, Advance Auto Parts has 232 different Differentials in our inventory ranging from $3.99 to $1,566.99. That means you can find the exact parts or products you need to keep that 2008 Ford E-450 Super Duty running smoothly.

Differentials are only as good as their brand. We stock 11 different brands to make sure you have plenty of trusted parts to choose from for your 2008 Ford E-450 Super Duty. Yukon Gear, National, and Driveworks are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Differentials for your 2008 Ford E-450 Super Duty, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 51 reviews in this category, some of the top rated parts include Tapered Cone Wheel Bearing Assembly with 4.0 stars and Differential Ring and Pinion with 4.0 stars.

So if you’re in the market for aftermarket Differentials to keep your 2008 Ford E-450 Super Duty rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Differentials Brands To Make Your 2008 Ford E-450 Super Duty Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 2008 Ford E-450 Super Duty demands trusted brand parts and products to keep it running. Many trusted brands of Differentials make up Advance Auto Parts’ inventory, and all are ready to help make your E-450 Super Duty the best it can be. Be sure to browse some of our top Differentials brands and parts.

Popular Felpro Differentials

We carry Felpro parts in our stock across Front Differential Cover Gaskets categories, plus more. For a 2008 Ford E-450 Super Duty, our most popular Felpro Differentials include:

from $15.99

(1)

Differential Cover Gasket

Front Differential Cover Gaskets

Top 2008 Ford E-450 Super Duty Differentials from National

National products are another trusted brand when it comes to Differentials for your 2008 Ford E-450 Super Duty. Popular National parts include:

from $9.99

(8)

Bearings

Rear Differential Pinion Bearings

FAQs for 2008 Ford E-450 Super Duty Differentials

What are the most purchased Differentials for the 2008 Ford E-450 Super Duty?

Out of 232 Differentials for the 2008 Ford E-450 Super Duty, the most popular in our inventory are:

from $57.99

This product is not rated

3 Qt – 80W90 Conventional Gear Oil With Posi Additive

Differential Oil

from $13.79

(4)

Taper Bearing Set

Differential Bearings

from $5.99

This product is not rated

Dana 60, Dana 70 & Dana 80 Cover Bolt

Differential Cover Bolts

What are the top-rated 2008 Ford E-450 Super Duty Differentials?

Top-rated Differentials for your 2008 Ford E-450 Super Duty based on customer reviews/ratings are:

from $16.99

(2)

Tapered Cone Wheel Bearing Assembly

“Worked sell”

from $245.99

(1)

Differential Ring and Pinion

“You get a good set of gears for a good price. Found same set other places for a lot more money. Would recommend this .”

from $13.99

(1)

Ford 10.25" & 10.5" Cover Gasket

“how the hell am i supposed to know what size and shape my differential cover gasket is?dana or ford.why isn’t there a vin entry somewhere on the webpa”

2008 Ford E-450 Super Duty Differentials

More 2008 Ford E-450 Super Duty Differentials

Essential 2008 Ford E-450 Super Duty Differentials

Motive Gear – Differential Master Bearing Kit – Koyo (Part No.R70HRMK)

Yukon Gear – Ring Gear Bolt For Ford 10.25" & 10.5" (Part No.33042)

Yukon Gear – Carrier Installation Kit For Dana 60 Differential (Part No.57005)

Yukon Gear – Dana 60 & Dana 70 Power Lok Case Bolt (Part No.33236)

Yukon Gear – Pinion Install Kit For Dana 80 Differential (4.375" OD Only) (Part No.13037)

Yukon Gear – Differential (Part No.26045)

Yukon Gear – Replacement Cover Gasket For Dana 50, Dana 60 & Dana 70 (Part No.23007)

Yukon Gear – Zip Locker Switch (Part No.34015)

Yukon Gear – Seal Housing For Dana 60, Zip Locker, With O-Rings (Part No.34039)

Yukon Gear – Ppinion Nut 7/8-20 Thread, 1 1/8 Socket (Part No.33146)

USA Standard Gear – Replacement Spider Gear Set For Dana 80, 37 Spline (Part No.39012)

Yukon Gear – Replacement Baffle For Dana 70 & 70HD (Part No.33003)

Driveworks – Differential Pinion Seal (Part No.S-100715-V)

USA Standard Gear – Master Overhaul Kit for ’07 & Down Ford 10.5 Differential (Part No.37085)

National – Bearings (Part No.A-50)

Yukon Gear – Replacement Pinion Nut Washer For Dana 80 (Part No.33165)

Yukon Gear – Conversioon Spacer To Use 10.25" Ring & Pinion In ’08 & Up 10.5" Housing (Part No.55054)

Yukon Gear – Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng (Part No.33327)

Yukon Gear – Dana 60 & Dana 70 Power Lok Cross Pin Shaft (Two Needed) (Part No.33315)

Yukon Gear – Side Gear Thrust Washer For Dana 60, 70 & 80 (Part No.33532)

Yukon Gear – Dana 70 & Dana 80 Pinion Gear Thrust Washer (Part No.33288)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

Felpro – Differential Cover Gasket (Part No.RDS 6014)

Yukon Gear – 1541H Alloy Left Hand Replacement Rear Axle For Dana 70 (Part No.21462)

Motive Gear – Differential Carrier Shim Kit (Part No.1106)

Yukon Gear – Dana 60 & Dana 61 Tracloc Clutch Set (Part No.16156)

Yukon Gear – Extra-Large Clamshells For Large Applciations (Part No.56059)

Yukon Gear – Zip Locker For Ford 10.25" & 10.5", Full Float Only (Part No.34025)

Popular 2008 Ford E-450 Super Duty Differentials Categories