2008 Cadillac Escalade ESV Fuel and Emissions Systems
Find Your Specific 2008 Cadillac Escalade ESV Fuel and Emissions Systems
Below you will find various in-demand Cadillac Fuel and Emissions Systems, components and accessories for your 2008 Escalade ESV. Advance Auto Parts has popular Escalade ESV parts like Air Flow Sensors, Oxygen Sensors, Fuel Injectors and more. You’ll also find aftermarket and OEM Fuel and Emissions Systems for other Escalade ESV model years including
2015,
2016,
2017,
2018,
2019,
2020,
2021,
2022,
2023 and more. Select a category of 2008 Cadillac Escalade ESV Fuel and Emissions Systems below and start saving instantly.
Popular 2008 Cadillac Escalade ESV Fuel and Emissions Systems Categories
Essential Fuel and Emissions Systems for 2008 Cadillac Escalade ESVs
GM Genuine Parts – Mass Airflow Sensor (Part No.23256991)
from
$222.99
GM Genuine Parts Mass Air Flow (MAF) Sensors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These sensors are key parts of the engine management system, and are GM-recommended replacements for your vehicle’s original components. The MAF sensor measures the amount of air entering the engine so that the engine control module can determine the amount of fuel to inject. This helps ensure the most efficient air/fuel mixture for the best fuel economy and power. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Measures the amount of air entering the engine so the ECM can determine the amount of fuel to inject
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Carquest Premium – Fuel Cap: 10834, Screw On, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10834)
from
$15.49
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Dorman – Fuel Clip, Ford, 5/16" (Part No.800-123.5)
from
$6.99
Fuel Clip, Ford, 5/16"
Carquest Premium – Remanufactured GDI Fuel Injector (Part No.A511-1053)
from
$94.99
CARQUEST’s line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the U.S.A. Each injector is 100% tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function. Each injector includes new external seals and o-rings.
Product Features:
See More
Product Features:
- Each unit is 100% tested to OE specifications.
- Includes new o-rings and seals made of premium OE quality materials.
- Includes application specific technical bulletin, where applicable.
ACDelco – GM Original Equipment Fuel Injector O-Ring Kit (Part No.C1013449577ACD)
from
$76.08
The ACDelco GM Original Equipment Fuel Injector O-Ring Kit is a GM-recommended replacement component that provides the same performance, durability, and service life as your factory original equipment.
Product Features:
See More
Product Features:
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Carquest Premium – Fuel Level Sensor (Part No.KBE1044)
from
$165.99
Fuel Level Sensor
Dorman – Fuel Sending Unit Pigtail (Part No.645-221)
from
$52.99
This fuel sender connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this fuel sender connector matches the appearance and function of the factory hardware on specified applications.
- Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Universal Fuel Line Retainer – 5/8 In. (Part No.800-041)
from
$12.29
This fuel line clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this fuel line clip matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
GM Genuine Parts – Vapor Canister Purge Tube (Part No.12575527)
from
$43.99
GM Genuine Parts Vapor Canister Purge Valve Pipes are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
ACDelco – GM Original Equipment Vapor Canister (Part No.B7070440030ACD)
from
$361.18
The ACDelco GM Original Equipment Vapor Canister is a GM-recommended replacement component that provides the same performance, durability, and service life as your factory original equipment.
Product Features:
See More
Product Features:
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
GM Genuine Parts – Fuel Injection Fuel Rail Bolt (Part No.12554211)
from
$9.99
GM Genuine Parts Studs are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
ACDelco – GM Original Equipment Fuel Pump Flow Control Module (Part No.E2031425029ACD)
from
$401.55
The ACDelco GM Original Equipment Fuel Pump Driver Module is a GM-recommended replacement for your vehicle’s original component. The Fuel Pump Driver Module is used on modern return-less fuel supply systems, where the fuel pump output is regulated based on engine speed and load. These modules control the voltage delivered to the vehicle’s fuel pump, regulating the fuel pump’s speed. This helps to maintain the optimum fuel pressure and fuel delivery to the engine throughout its full operating range. This original equipment module has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- GM-recommended replacement part for your GM vehicle’s original factory fuel pump driver module
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Carquest Premium – Reman GDI Fuel Injector – 8 Pack (Part No.A511-1053-8PK)
from
$509.99
The Carquest line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the USA. Injectors are thoroughly tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function.
Product Features:
See More
Product Features:
- Includes eight premium fuel injectors
- Each unit is 100% tested to OE specifications
- Includes new o-rings and seals made of premium OE quality materials
- Includes application specific technical bulletin, where applicable
Carquest Premium – Connector (Part No.PTA2867)
from
$15.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
Product Features:
See More
Product Features:
- Premium quality materials for longer service life
- Sealed connections (where applicable) to prevent environmental corrosion and performance issues
- Global coverage for import and/or domestic applications
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
ACDelco – Fuel Tank Pressureensor (Part No.13502903)
from
$82.99
ACDelco GM Original Equipment Fuel Tank Pressure Sensors are GM-recommended replacements for your vehicle’s original components. These sensors help measure pressure changes within your vehicle’s fuel tank. They also help alert your vehicle’s engine management computer if a leak occurs in your vehicle’s fuel system. These original equipment sensors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- Help measure pressure changes within fuel tank
- Help alert engine management computer if a leak occurs in fuel system
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Felpro – Exhaust Gas Recirculation (EGR) Valve Gasket (Part No.70947)
from
$2.79
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Validated for fit, form and function
- Unsurpassed quality you can trust
GM Genuine Parts – Fuel Injector Retainer Kit with Clip (Part No.12570620)
from
$13.79
GM Genuine Parts Fuel Injector and Insulator Retainer Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Carquest Premium – Fuel Injection Pressure Sensor (Part No.FPA1017)
from
$39.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
Dorman – Fuel Filler Neck (Part No.577-311)
from
$544.99
Fuel filler neck leaking? This replacement fuel filler neck is precision-engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair.
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck is made to match the original equipment on specific vehicles.
- Durable construction – made of corrosion-resistant materials to reduce future failure potential.
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
ACDelco – Black Multi-Purpose Pigtail (Part No.PT1274)
from
$51.99
ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- Protective outer coverings help provide long-lasting durability
- Color-coded wires allow for easy installation
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
DENSO – Oxygen Sensor: 4 Wire, 16.14" Long, Heated, Exact Fit (Part No.234-4337)
from
$99.99
DENSO Oxygen Sensors are manufactured and tested to the strictest OE standards for unparalleled performance. Each component is precision built for exact replacement, and a first time fit. This innovative line features DENSO’s exclusive aluminum oxide trap layer, designed to protect the ceramic element from silicone and lead posining for improved engine performance, greater fuel efficiency, and unparalleled longevity. DENSO gives you the right part and the right fit, the first time.
Product Features:
See More
Product Features:
- Specifically designed to meet the increasing demands of today’s engines
- 100% checked for high temperature signal output, air tightness, continuity, and heat resistance for optimal efficiency and performance
- Coated with aluminum oxide to prevent silicone and lead from contacting the ceramic element and damaging the platinum electrode
- Double protection cover helps maintain proper unit temperature for quicker response times, which is critical to your vehicle’s fuel efficiency
- Manufactured with a rugged stainless steel housing and porous PTFE filter to resist corrosion and contamination
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.61824)
from
$15.29
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Dorman – Evaporative Emissions Purge Solenoid Valve (Part No.911-068)
from
$48.49
Engineered for a perfect fit and plug-and-play installation, this vapor canister purge valve is a direct replacement for the original equipment purge valve. It is critical to the evaporative emissions system and fulfills government requirements.
Product Features:
See More
Product Features:
- Direct replacement – this vapor canister purge valve fits and functions like original equipment to ensure proper function of your vehicle’s evaporative emissions system.
- Quality construction – manufactured from premium materials for a long service life.
- Excellent value – original equipment quality at a lower price
- Quality tested – has undergone testing to ensure proper fit and performance
ACDelco – 3-Way Female Black Multi-Purpose Pigtail (Part No.PT420)
from
$40.99
ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- Protective outer coverings help provide long-lasting durability
- Color-coded wires allow for easy installation
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Dorman – Fuel Pump Driver Module – OE Fix (Part No.601-131)
from
$194.99
If your GM vehicle starts hard, stalls or is running poorly, it could be because of a failing fuel pump driver module. But when the factory module fails on select models, the dealership’s replacement part requires expensive calibration and programming. This time-saving Dorman OE FIX replacement is pre-programmed for an easier and more predictable installation. It also features a thermal- and vibration-tested backing plate for greater resistance to corrosion, and upgraded active electronic components for added reliability.
Product Features:
See More
Product Features:
- Pre-programmed replacement – this fuel pump driver module for GM vehicles directly replaces the original and requires no programming for installation
- Upgraded design – module features enhanced microcontroller and new active electronic components for added reliability
- Durable construction – module housing is thermal- and vibration-tested, with a powder-coated aluminum backing plate for corrosion resistance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Carquest Premium – Fuel Tank Lock Ring LO1582926 (Part No.LO1582926)
from
$15.99
Carquest Premium offers a complete line of fuel tank lock rings covering a wide variety of North American vehicle applications. Carquest Premium fuel tank lock rings are engineered to meet or exceed all OEM specifications. Carquest Premium fuel tank lock rings are precision stamped and are treated with a rust proof finish to ensure durability and strength.
Product Features:
See More
Product Features:
- Engineered to meet or exceed all OEM specifications
- Precision stamped and are treated with a rust proof finish to ensure durability and strength
Dorman – Vapor Canister Vent (Part No.B7091829268DOR)
from
$117.92
Vapor Canister Vent
Carquest Premium – Vapor Canister Purge Solenoid (Part No.CPC1019)
from
$44.99
Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
Upgrade your 2008 Cadillac Escalade ESV with Top-Quality Fuel and Emissions Systems
When it comes to maintaining or upgrading your 2008 Cadillac Escalade ESV, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Cadillac or enhancing its overall performance, Fuel and Emissions Systems are key to keeping your Escalade ESV functioning at its best. At Advance Auto Parts, we offer a wide selection of 106 Fuel and Emissions Systems for the 2008 Cadillac Escalade ESV, designed to meet your needs without breaking the bank.
From
Air Flow Sensor
replacements to
Oxygen Sensors
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Fuel and Emissions Systems for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Fuel and Emissions Systems for your 2008 Cadillac Escalade ESV at great prices.
Our Fuel and Emissions Systems inventory for this model
ranges from just $1.79 to $419.99, with
an average price of $80.10.
Our 106 Fuel and Emissions Systems in stock come from 15 trusted brands, so you’re sure to find the right part for your 2008 Cadillac Escalade ESV without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2008 Cadillac Escalade ESV, we stock popular OEM and aftermarket Fuel and Emissions Systems from top names
like FELPRO, Carquest Premium, Dorman, and more.
FELPRO Fuel and Emissions Systems
start at just $2.29 and boast an impressive 4.6 stars average rating from customers.
Carquest Premium and Dorman also bring quality to the table, with Fuel and Emissions Systems available starting at $6.99, and at an average 4.4 stars rating.
With 1,668 customer reviews and counting, our 2008 Cadillac Escalade ESV Fuel and Emissions Systems have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Fuel and Emissions System upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 2008 Cadillac Escalade ESV is always ready to roll. We’re committed to providing you with everything you need to keep your Escalade ESV in top shape, all in one place.
Start shopping confidently below for your 2008 Cadillac Escalade ESV!
Best-Selling Air Flow Sensors for 2008 Cadillac Escalade ESVs
Enhance the driving experience in your Cadillac with 6 quality Air Flow Sensor components, starting at $13.99.
ACDelco – Manifold Absolute Pressure (MAP) Sensor (Part No.213-796)
from
$89.99
ACDelco GM Original Equipment Manifold Absolute Pressure (MAP) Sensors measure intake manifold pressure, and are GM-recommended replacements for your vehicle’s original components. The MAP sensor is a part of the fuel and engine management system. Its signal is used by the engine control module along with the throttle position sensor to calculate the amount of air entering the engine so that the correct amount of fuel is injected for optimum combustion. These original equipment manifold absolute pressure sensors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- Sends signals to the engine controls for optimal engine performance
- Designed to adjust engine performance to various altitudes
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Carquest Premium – Manifold Absolute Pressure Sensor (MAP) (Part No.ECC1011)
from
$66.99
CARQUEST MAP sensors are manufactured with critical OEM components to ensure that your engine runs efficiently to reach the best gas mileage on your vehicle.
Product Features:
See More
Product Features:
- CARQUEST MAP sensors connectors are exact OE fit to ensure the proper vacuum is maintained to prevent power loss and to minimize internal contamination.
- CARQUEST MAP sensors utilize high temperature resistant seals. Damaged seals can directly impact the vehicles fuel-to-air ratio, making it less fuel efficient.
- CARQUEST MAP sensors are 100% individually tested for all product functionalities including proper vacuum seal and electrical output.
NTK – Manifold Absolute Pressure Sensor (Part No.MA0097)
from
$79.99
Building upon a foundation of premium full-line products established under NGK ignition and NTK oxygen sensor products, NTK’s expansion to technical sensors is part of our ongoing commitment to streamline product types and increase coverage under one premium brand: NTK, The Sensor Specialist. With over 80 years of automotive expertise, NGK’s family of automotive products are driven by extreme dedication to innovation, performance and quality. NTK is the only OE supplier with a full-line of technical sensors in the aftermarket for import and domestic vehicles. Drawing from OE experience, NTK sensors undergo extreme testing conditions that include thermal shock, vibration and OBD verification. NTK sensors are manufactured to ensure a quality that meets or exceeds OE specifications. As new vehicles incorporate connected and automated technologies, trust The Sensor Specialist for full-line market support and OE application technology.
Product Features:
See More
Product Features:
- NTK’s Manifold Absolute Pressure Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function to ensure proper manifold pressure, fuel metering and ignition timing.
- The Manifold Absolute Pressure Sensor (MAP) provides manifold pressure information to the Engine Control Unit (ECU). The data is used to determine the air mass flow rate and required fuel for optimum combustion and ignition timing.
GM Genuine Parts – Manifold Absolute Pressure Sensor (Part No.19418808)
from
$109.99
Manifold Absolute Pressure Sensor
Dorman – GM Multi-Purpose Socket With Pigtails (Part No.645-500)
from
$24.79
Make better electrical repairs and accessory installations with this pigtail connector. Designed for a clean appearance when installed, it features weatherproof terminals and a locking tab for a reliable quick disconnect electrical connection.
Product Features:
See More
Product Features:
- Professional appearance – this electrical pigtail is designed for a clean, professional look when installed.
- Convenient solution – this pigtail connector allows the circuit to be quickly disconnected for service or occasional use
- Durable construction – this pigtail connector features weatherproof seals and a locking tab for a reliable connection
- Versatile component – this connector can be used in a variety of repairs and custom installations
GM Genuine Parts – Manifold Absolute Pressure Sensor Seal (Part No.16194007)
from
$13.99
GM Genuine Parts Manifold Absolute Pressure Sensor Seals are designed, engineered, & tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Most Popular 2008 Cadillac Escalade ESV Oxygen Sensors
Customize your Cadillac with 19 Oxygen Sensors products
like Oxygen Sensors and
Oxygen Sensor Connectors, all
priced under $132.99.
NTK – Switching Oxygen Sensor: 4 Wire, 15" Long, Heated, Direct Fit (Part No.21066)
from
$86.99
NTK is the world’s largest supplier and manufacturer of OEM oxygen sensors. Oxygen sensors play a critical role as part of the vehicle’s on-board diagnostic system in maintaining optimal engine performance, maximizing fuel efficiency and reducing harmful emissions. Providing constant closed loop feedback to the ECU, oxygen sensors help to control the air-fuel ratio while alerting OBDII systems of possible problems with fuel delivery or catalytic converter efficiency. A ceramics company at our core, NTK uses state-of-the art technology enabling control of the ceramic element used in our oxygen sensors from raw material to finished product. Trust The Sensor Specialist for full-line market support and OE application technology.
Product Features:
See More
Product Features:
- OEM QUALITY: NTK is the world’s largest supplier of original equipment oxygen sensors with renowned quality that meets or exceeds OEM specifications
- PRODUCT ENGINEERING: Based on OE expertise, but specifically engineered for the aftermarket, NTK Oxygen Sensors offer superior OE fit, form, function
- OE TECHNOLOGY: Upgraded to the latest OE technologies, NTK Oxygen Sensors are designed to reduce OE failures, enhance durability and performance
- EXTENSIVE TESTING: OE development includes vibration and thermal shock testing. Testing during manufacturing guarantees quality and reliability
- EASY INSTALLATION: NTK Oxygen Sensors are equipped with OE specified, water-resistant connectors and harness accessory hardware for easy installation
- ADVANCED CERAMIC SENSOR ELEMENT: 3-stage contaminant-resistant plasma jet and deposit trap overcoat protects against element poisoning
- NTK ADVANTAGE: Superior dual-coated platinum interface and thinner ceramic element produces fastest light off and response times with best durability
NTK – Switching Oxygen Sensor: 4 Wire, 16.5" Long, Heated, Direct Fit (Part No.21546)
from
$68.99
NTK is the world’s largest supplier and manufacturer of OEM oxygen sensors. Oxygen sensors play a critical role as part of the vehicle’s on-board diagnostic system in maintaining optimal engine performance, maximizing fuel efficiency and reducing harmful emissions. Providing constant closed loop feedback to the ECU, oxygen sensors help to control the air-fuel ratio while alerting OBDII systems of possible problems with fuel delivery or catalytic converter efficiency. A ceramics company at our core, NTK uses state-of-the art technology enabling control of the ceramic element used in our oxygen sensors from raw material to finished product. Trust The Sensor Specialist for full-line market support and OE application technology.
Product Features:
See More
Product Features:
- OEM QUALITY: NTK is the world’s largest supplier of original equipment oxygen sensors with renowned quality that meets or exceeds OEM specifications
- PRODUCT ENGINEERING: Based on OE expertise, but specifically engineered for the aftermarket, NTK Oxygen Sensors offer superior OE fit, form, function
- OE TECHNOLOGY: Upgraded to the latest OE technologies, NTK Oxygen Sensors are designed to reduce OE failures, enhance durability and performance
- EXTENSIVE TESTING: OE development includes vibration and thermal shock testing. Testing during manufacturing guarantees quality and reliability
- EASY INSTALLATION: NTK Oxygen Sensors are equipped with OE specified, water-resistant connectors and harness accessory hardware for easy installation
- ADVANCED CERAMIC SENSOR ELEMENT: 3-stage contaminant-resistant plasma jet and deposit trap overcoat protects against element poisoning
- NTK ADVANTAGE: Superior dual-coated platinum interface and thinner ceramic element produces fastest light off and response times with best durability
DENSO – First Time Fit Oxygen Sensor (Part No.C5010422568ND)
from
$65.64
Denso First Time Fit oxygen sensors are constructed of the highest quality materials available. High-quality stainless steel, porous polytetrafluoroethylene (PTFE), fluorine rubber, aluminum oxide, high-grade platinum and ceramics are used in each DENSO sensor.
Product Features:
See More
Product Features:
- SUPERIOR DESIGN – Maximizes engine performance and fuel efficiency while reducing harmful emissions.
- DOUBLE-PROTECTION COVER – Maintains proper unit temperature for quicker response times and protects the ceramic element against silicone and lead poisoning.
- ALUMINUM-OXIDE TRAP LAYER – Keeps silicone and lead outside the ceramic element through DENSO’s exclusive design, preventing damage to the platinum electrode.
- STAINLESS STEEL HOUSING – Resists corrosion and contamination with a rugged, watertight body.
Bosch – Oxygen Sensor: 4 Wire, 15.87" Long, Heated, Exact Fit (Part No.15200)
from
$132.99
Bosch is the world’s leading supplier and original equipment manufacturer of Oxygen Sensors. Bosch invented the automotive oxygen sensor and leads the way in sensor technology and innovation. From overall sensor design to the critical ceramic element, Bosch is known worldwide for quality and performance.
Product Features:
See More
Product Features:
- Premium Bosch oxygen sensors are designed to improve fuel economy while reducing harmful emissions
- Direct Fit includes OE Connector for easy installation
- Performance meets or exceeds OE specifications
- True Direct-fit OE connectors and harness
DENSO – Oxygen Sensor: 4 Wire, 15.75" Long, Heated, Exact Fit (Part No.234-4668)
from
$63.99
DENSO Oxygen Sensors are manufactured and tested to the strictest OE standards for unparalleled performance. Each component is precision built for exact replacement, and a first time fit. This innovative line features DENSO’s exclusive aluminum oxide trap layer, designed to protect the ceramic element from silicone and lead posining for improved engine performance, greater fuel efficiency, and unparalleled longevity. DENSO gives you the right part and the right fit, the first time.
Product Features:
See More
Product Features:
- Specifically designed to meet the increasing demands of today’s engines
- 100% checked for high temperature signal output, air tightness, continuity, and heat resistance for optimal efficiency and performance
- Coated with aluminum oxide to prevent silicone and lead from contacting the ceramic element and damaging the platinum electrode
- Double protection cover helps maintain proper unit temperature for quicker response times, which is critical to your vehicle’s fuel efficiency
- Manufactured with a rugged stainless steel housing and porous PTFE filter to resist corrosion and contamination
DENSO – Oxygen Sensor: Downstream, 4 Wire, 14.80" Long, Heated, Exact Fit (Part No.234-4256)
from
$101.99
DENSO Oxygen Sensors are manufactured and tested to the strictest OE standards for unparalleled performance. Each component is precision built for exact replacement, and a first time fit. This innovative line features DENSO’s exclusive aluminum oxide trap layer, designed to protect the ceramic element from silicone and lead posining for improved engine performance, greater fuel efficiency, and unparalleled longevity. DENSO gives you the right part and the right fit, the first time.
Product Features:
See More
Product Features:
- Specifically designed to meet the increasing demands of today’s engines
- 100% checked for high temperature signal output, air tightness, continuity, and heat resistance for optimal efficiency and performance
- Coated with aluminum oxide to prevent silicone and lead from contacting the ceramic element and damaging the platinum electrode
- Double protection cover helps maintain proper unit temperature for quicker response times, which is critical to your vehicle’s fuel efficiency
- Manufactured with a rugged stainless steel housing and porous PTFE filter to resist corrosion and contamination
Bosch – Oxygen Sensor: 4 Wire, 24.02" Long, Heated, Universal (Part No.15730)
from
$77.99
Bosch is the world’s leading supplier and original equipment manufacturer of Oxygen Sensors. Bosch invented the automotive oxygen sensor and leads the way in sensor technology and innovation. From overall sensor design to the critical ceramic element, Bosch is known worldwide for quality and performance.
Product Features:
See More
Product Features:
- Premium Bosch oxygen sensors are designed to improve fuel economy while reducing harmful emissions
- Includes Smart Link Connector, no soldering required
- No special tools required for installation
- Seared protection tube due to 100% functional quality test
- Performance meets or exceeds OE specifications
DENSO – Oxygen Sensor: 4 Wire, 11.77" Long, Heated, Universal Fit (Part No.234-4212)
from
$69.99
DENSO Oxygen Sensors are manufactured and tested to the strictest OE standards for unparalleled performance. Each component is precision built for exact replacement, and a first time fit. This innovative line features DENSO’s exclusive aluminum oxide trap layer, designed to protect the ceramic element from silicone and lead posining for improved engine performance, greater fuel efficiency, and unparalleled longevity. DENSO gives you the right part and the right fit, the first time.
Product Features:
See More
Product Features:
- Specifically designed to meet the increasing demands of today’s engines
- 100% checked for high temperature signal output, air tightness, continuity, and heat resistance for optimal efficiency and performance
- Coated with aluminum oxide to prevent silicone and lead from contacting the ceramic element and damaging the platinum electrode
- Double protection cover helps maintain proper unit temperature for quicker response times, which is critical to your vehicle’s fuel efficiency
- Manufactured with a rugged stainless steel housing and porous PTFE filter to resist corrosion and contamination
Bosch – Oxygen Sensor: 4 Wire, 25.87" Long, Heated, Universal (Part No.15741)
from
$62.99
Bosch is the world’s leading supplier and original equipment manufacturer of Oxygen Sensors. Bosch invented the automotive oxygen sensor and leads the way in sensor technology and innovation. From overall sensor design to the critical ceramic element, Bosch is known worldwide for quality and performance.
Product Features:
See More
Product Features:
- Premium Bosch oxygen sensors are designed to improve fuel economy while reducing harmful emissions
- Includes Smart Link Connector, no soldering required
- No special tools required for installation
- Seared protection tube due to 100% functional quality test
- Performance meets or exceeds OE specifications
GM Genuine Parts – Oxygen Sensor: 4 Wires, 330 mm Long, Heated, Exact Fit (Part No.213-4229)
from
$65.99
GM Genuine Parts Oxygen (O2) Sensors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These sensors are special feedback sensors on your vehicle’s exhaust system and measure the proportion of oxygen in exhaust gases. Using this measurement, the engine control module (ECM) can adjust the air/fuel ratio to near the optimal value of 14.7:1. At this ratio, engine performance, emissions, and fuel economy are all optimized. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Detects oxygen content in the exhaust gases to help optimize emissions
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
GM Genuine Parts – Oxygen Sensor: 4 Wires, 323 mm Long, Heated, Exact Fit (Part No.213-3866)
from
$79.99
GM Genuine Parts Oxygen (O2) Sensors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These sensors are special feedback sensors on your vehicle’s exhaust system and measure the proportion of oxygen in exhaust gases. Using this measurement, the engine control module (ECM) can adjust the air/fuel ratio to near the optimal value of 14.7:1. At this ratio, engine performance, emissions, and fuel economy are all optimized. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Detects oxygen content in the exhaust gases to help optimize emissions
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Bosch – Oxygen Sensor: 4 Wire, 16.93" Long, Heated, Exact Fit (Part No.15698)
from
$67.99
Bosch is the world’s leading supplier and original equipment manufacturer of Oxygen Sensors. Bosch invented the automotive oxygen sensor and leads the way in sensor technology and innovation. From overall sensor design to the critical ceramic element, Bosch is known worldwide for quality and performance.
Product Features:
See More
Product Features:
- Premium Bosch oxygen sensors are designed to improve fuel economy while reducing harmful emissions
- Direct Fit includes OE Connector for easy installation
- Performance meets or exceeds OE specifications
- True Direct-fit OE connectors and harness
ACDelco – GM Original Equipment Oxygen Sensor: Enhances Engine Performance and Emissions (Part No.C5010307792ACD)
from
$93.25
The ACDelco GM Original Equipment Oxygen (O2) Sensor is a GM-recommended replacement for your vehicle’s original component. The Oxygen (O2) Sensor is a special feedback sensor on your vehicle’s exhaust system. This sensor measures the proportion of oxygen in the exhaust gases. Using this measurement, the engine management computer can adjust the air/fuel ratio near the optimum value of 14.7:1. At this ratio, engine performance, emissions, and fuel economy are all optimized. This original equipment oxygen sensor has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors. When you are looking for a match to GM Original Equipment specifications in a replacement part for your GM vehicle, trust ACDelco to get the job done.
Product Features:
See More
Product Features:
- Detect oxygen content in the exhaust gases to optimize emissions and fuel economy
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Carquest Premium – Oxygen Sensor Connector (Part No.PTA1317)
from
$68.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
Product Features:
See More
Product Features:
- Premium quality materials for longer service life
- Sealed connections (where applicable) to prevent environmental corrosion and performance issues
- Global coverage for import and/or domestic applications
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
DENSO – Oxygen Sensor (Part No.C5010690176ND)
from
$78.46
Oxygen Sensor
Bosch – Oxygen Sensor (Part No.C50101333650BOS)
from
$97.19
Oxygen Sensor
Carquest Premium – Oxygen Sensor Connector (Part No.PTA1517)
from
$53.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
Product Features:
See More
Product Features:
- Premium quality materials for longer service life
- Sealed connections (where applicable) to prevent environmental corrosion and performance issues
- Global coverage for import and/or domestic applications
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Carquest Premium – Engine Crankshaft Position Sensor Connector (Part No.PTA2455)
from
$102.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More
ACDelco – GM Original Equipment Oxygen Sensor: Optimal Engine Performance and Fuel Economy (Part No.C5010352631ACD)
from
$86.07
The ACDelco GM Original Equipment Oxygen (O2) Sensor is a GM-recommended replacement for your vehicle’s original component. The Oxygen (O2) Sensor is a special feedback sensor on your vehicle’s exhaust system. This sensor measures the proportion of oxygen in the exhaust gases. Using this measurement, the engine management computer can adjust the air/fuel ratio near the optimum value of 14.7:1. At this ratio, engine performance, emissions, and fuel economy are all optimized. This original equipment oxygen sensor has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors. When you are looking for a match to GM Original Equipment specifications in a replacement part for your GM vehicle, trust ACDelco to get the job done.
Product Features:
See More
Product Features:
- Detect oxygen content in the exhaust gases to optimize emissions and fuel economy
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Top Picks for 2008 Cadillac Escalade ESV Fuel Injectors
Upgrade Cadillac Escalade ESVs with top-quality Fuel Injectors parts, including 17 OEM and aftermarket selections for your 2008 model.
Carquest Premium – Mass Air Flow Sensor (MAF) – 100% NEW (Part No.MQ6208)
from
$65.99
Advance Auto Parts is proud to carry all new mass air flow sensors that use high-quality components with the highest quality standards.
Product Features:
See More
Product Features:
- CARQUEST MAF use all new high-quality components at the highest quality standards.
- Manufactured with new and advanced technology to perform, fit and function at OE specifications.
- All new product that is tested with OEM equipment to OEM standards
- Outperforms competition when tested in extreme environmental conditions
Felpro – Fuel Injector O-Ring Kit (Part No.ES 71190)
from
$8.99
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.61469)
from
$13.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
GM Genuine Parts – Fuel Injector O-Ring Kit with Assorted O-Rings (Part No.217-1588)
from
$29.99
GM Genuine Parts Fuel Injector Seal Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These seals help provide liquid-tight connections between the fuel injector and related components. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Helps provide a seal to prevent fuel leaks
- Helps seal combustion chamber from the elements
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Mahle – Throttle Body Gasket (Part No.C7001291899MAH)
from
$21.80
MAHLE Cleveite Inc. is not responsible for failures resulting from owner, operator or third party abuse or neglect including, but not limited to engine operation without adequate lubricant or coolant, over or under-fuelling, over-speeding, lack of proper maintenance to cooling, lubrication or air intake systems, improper storage, starting, warm-up, run-in or shutdown procedures or the continued operation of an engine after the first sign of a malfunction. MAHLE Cleveite Inc. is not responsible for failures resulting from improper installation or repair procedures, alteration or the misapplication of parts, or use in engines modified for competition or levels of performance beyond the engine manufacturers original specifications. Mahle/Cleveite – (The MAHLE Group) is one of the largest global automotive parts manufacturers, specializing in Engine Components, Filtration and Peripherals.
See More
Delphi – Mass Air Flow Sensor (Part No.AF10058)
from
$106.99
100% new; Delphi OE Technology Validated to match the vehicle applications; Manufactured to meet or exceed OE requirements.
Product Features:
See More
Product Features:
- Delphi mass air flow sensors are the global benchmark for accuracy and signal noise
- Delphi mass air flow sensors feature high quality sensing elements for outstanding performance over a wide range of ambient temperatures
- Delphi is a manufacturer of OE mass air flow sensors since their first use over 30 years ago
- All parts are calibrated and tested to match the OE part
- Probe solution offered wherever possible to reduce repair time by eliminating the need to replace the flow tube.
- Delphi OE technology validated to match the vehicle applications
Carquest Premium – Remanufactured Fuel Injector (Part No.A211-2033)
from
$69.99
CARQUEST’S line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the U.S.A. Each injector is 100% tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function. Each injector includes new external seals and O-rings.
Product Features:
See More
Product Features:
- Each unit is 100% tested to OE specifications
- Includes new O-rings and seals made of premium OE quality materials
- Includes application specific technical bulletin, where applicable
ACDelco – Sequential Multi-Port Fuel Injector Assembly (Part No.217-1621)
from
$131.99
ACDelco GM Original Equipment Fuel Injectors are electro-magnetic valves that meter fuel into the engine’s intake manifold or cylinders for combustion, and are GM-recommended replacements for your vehicle’s original components. The engine control module (ECM) operates the injector by applying an electric current to the injector solenoid winding, causing the needle valve to open, and allowing pressurized fuel to be atomized into the intake airstream. These original equipment fuel injectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Atomizes fuel into the engine’s intake manifold or cylinders, as part of the fuel and engine management system
- Allows for a quick throttle response
- Assists in cold engine starts
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
ACDelco – GM Original Equipment Fuel Injection Throttle Body Gasket (Part No.C7001291899ACD)
from
$55.74
The ACDelco GM Original Equipment Fuel Injection Throttle Body Gasket is a GM-recommended replacement component that provides the same performance, durability, and service life as your factory original equipment.
Product Features:
See More
Product Features:
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Felpro – Fuel Injector O-Ring Kit (Part No.ES 73217)
from
$25.49
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
GM Genuine Parts – Fuel Pressure Relief Valve Cap (Part No.214-1044)
from
$6.29
GM Genuine Parts Fuel Pressure Relief Valve Caps are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
GM Genuine Parts – Fuel Injector Retainer Kit with Clip (Part No.12570620)
from
$13.79
GM Genuine Parts Fuel Injector and Insulator Retainer Kits are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Carquest Premium – Reman Multi Port Fuel Injector – 8 Pack (Part No.A211-2033-8PK)
from
$419.99
The Carquest line of remanufactured OEM fuel injectors are remanufactured using a proven 15 step process at a state-of-the-art remanufacturing facility in the USA. Injectors are thoroughly tested under multiple operating conditions to ensure each injector meets or exceeds OE specifications for flow rate, spray pattern, coil resistance, form, fit and function.
Product Features:
See More
Product Features:
- Includes eight premium fuel injectors
- Each unit is 100% tested to OE specifications
- Includes new o-rings and seals made of premium OE quality materials
- Includes application specific technical bulletin, where applicable
GM Genuine Parts – Sequential Multiport Fuel Injector (Part No.19421333)
from
$157.99
GM Genuine Parts Fuel Injectors are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These fuel injectors are electro-magnetic valves that meter fuel into the engine’s intake manifold or cylinders for combustion. The engine control module (ECM) operates the injector by applying an electric current to the injector solenoid winding, causing the needle valve to open, and allowing pressurized fuel to be atomized into the intake airstream. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Atomizes fuel into the engine’s intake manifold or cylinders, as part of the fuel and engine management system
- Allows for a quick throttle response
- Assists in cold engine starts
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
ACDelco – GM Original Equipment Fuel Injector Seal Kit (Part No.C1060205441ACD)
from
$37.69
The ACDelco GM Original Equipment Fuel Injector Seal Kit is a GM-recommended replacement component that provides the same performance, durability, and service life as your factory original equipment.
Product Features:
See More
Product Features:
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Victor Reinz – Fuel Injector O-Ring Kit (Part No.18-10027-01)
from
$8.79
With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.
Product Features:
See More
Product Features:
- Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
Felpro – Fuel Injector O-Ring (Part No.C1013975873FEL)
from
$7.92
Fuel Injector O-Ring
In-Demand Gas Caps for 2008 Cadillac Escalade ESVs
Select from 9 premium Gas Caps parts for your 2008 Cadillac Escalade ESV, with prices ranging from $18.79 to $63.71.
Carquest Premium – Keyed Alike Locking Fuel Cap (Part No.17511)
from
$19.99
None
Product Features:
See More
Product Features:
- Reduces air pollution with proper sealing and venting
- Manufactured from durable, long-life materials
- Independently tested for emission control
- Passes all state and federal emissions tests
- Reduces air pollution with proper sealing and venting
Carquest Premium – Locking Fuel Cap: 10518, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10518)
from
$24.99
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Protects your fuel from theft and vandalism
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Carquest Premium – Fuel Cap: 10841, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10841)
from
$21.79
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Carquest Premium – Locking Fuel Cap: 10511, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10511)
from
$27.49
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Protects your fuel from theft and vandalism
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Carquest Premium – Fuel Cap: 10848, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10848)
from
$18.79
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Carquest Premium – Locking Fuel Cap: 10523, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10523)
from
$23.99
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Protects your fuel from theft and vandalism
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Motorad – Tethered Fuel Cap (Part No.MGC840T)
from
$30.99
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Come pre-assembled for quick and easy installation.
- Several fastener options to work with any fuel cap compartment configuration
- Fits vehicles orginally equipped with tether
- Reduces air pollution with proper sealing and venting
- Manufactured from durable, long-life materials
ACDelco – GM Original Equipment Fuel Cap (Part No.E2010430522ACD)
from
$63.71
The ACDelco GM Original Equipment Fuel Cap is a threaded cap that seals your vehicle’s fuel tank filler, and is a GM-recommended replacement for your vehicle’s original component. The fuel cap has a rubber gasket that provides a liquid-tight seal to keep fuel in and water and dirt out. The cap may have a check-valve that lets air in or out depending on the air pressure inside the tank. This original equipment regular fuel cap has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- Provides a tight seal to keep your vehicle’s fuel tank closed
- A sealed fuel tank reduces vapor emissions which helps the environment
- Prevents lost fuel in order to help reduce your trips to the gas station
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Carquest Premium – Keyed Alike Locking Fuel Cap (Part No.17518)
from
$18.79
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Protects your fuel from theft and vandalism
- Manufactured from durable, long-life materials
- Independently tested for emission control
- Passes all state and federal emissions tests
- Reduces air pollution with proper sealing and venting
Most Sold 2008 Cadillac Escalade ESV Fuel Pumps
Explore our best-selling Cadillac parts for the 2008 Escalade ESV among 10 OEM and aftermarket options starting from $39.99.
GM Genuine Parts – Fuel Pump Flow Control Module (Part No.20759945)
from
$189.99
GM Genuine Parts Fuel Pump Control Modules are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These modules help relay power to your vehicle’s fuel pump. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- This part requires programming and/or special setup procedures. GM Service Information describes the procedures and special tools needed to ensure proper operation in the vehicle
- Helps power the fuel pump
- Helps your vehicle to idle smoothly
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
ACDelco – 4-Way Female Gray Multi-Purpose Pigtail (Part No.PT1069)
from
$64.99
ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- Protective outer coverings help provide long-lasting durability
- Color-coded wires allow for easy installation
- GM-recommended replacement part for your GM vehicle’s original factory component
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Delphi – Fuel Pump Module Assembly: With Float Arm, Seal (Part No.FG1154)
from
$372.99
100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.
Product Features:
See More
Product Features:
- Delphi is a global OE manufacturer and all fuel pumps are built to Delphi’s OE standards
- Empty float height and float retention matches OE specifications and guarantees correct gas gauge reading
- Lower amperage draws less load on vehicle’s electrical system
- Part is validated, tested and matched to the right vehicle application
- Always be sure to check and clean fuel tank to avoid unnecessary returns
- Lower failure rates due to its innovative design and durability
ACDelco – GM Original Equipment Fuel Pump Flow Control Module (Part No.E2031425029ACD)
from
$401.55
The ACDelco GM Original Equipment Fuel Pump Driver Module is a GM-recommended replacement for your vehicle’s original component. The Fuel Pump Driver Module is used on modern return-less fuel supply systems, where the fuel pump output is regulated based on engine speed and load. These modules control the voltage delivered to the vehicle’s fuel pump, regulating the fuel pump’s speed. This helps to maintain the optimum fuel pressure and fuel delivery to the engine throughout its full operating range. This original equipment module has been manufactured to fit your specific GM vehicle, providing the same performance, durability, and service life you expect from General Motors.
Product Features:
See More
Product Features:
- GM-recommended replacement part for your GM vehicle’s original factory fuel pump driver module
- Offering the quality, reliability, and durability of GM OE
- Manufactured to GM OE specification for fit, form, and function
Bosch – Fuel Pump Assembly (Part No.E3001926133BOS)
from
$392.44
Fuel Pump Assembly
Spectra Premium – Module Assy (Part No.SP6034M)
from
$268.39
CARQUEST fuel pump modules offer OEM or better performance from an Original Equipment Supplier. The latest advancements in fuel delivery technology are built-in to every CARQUEST Fuel Pump to deliver greater reliability.
Product Features:
See More
Product Features:
- Every single pump is 100% tested throughout the entire manufacturing process for worry free, out-of-the-box performance
- Triple barb hose fitting provides superior, long-lasting seal
- Superior return porting for optimum fuel flow
- Enhanced pump to flange harness design provides worry-free electrical performance
- Ceramic sender card and float arm that utilizes vehicle-specific geometry to ensure accurate fuel gauge readings for each and every application
- Gradient density, dual zone filtration designed for better contamination resistance
Dorman – Fuel Pump Driver Module – OE Fix (Part No.601-132)
from
$221.99
If your GM vehicle starts hard, stalls or is running poorly, it could be because of a failing fuel pump driver module. But when the factory module fails on select models, the dealership’s replacement part requires expensive calibration and programming. This time-saving Dorman OE FIX replacement is pre-programmed for an easier and more predictable installation. It also features a thermal- and vibration-tested backing plate for greater resistance to corrosion, and upgraded active electronic components for added reliability.
Product Features:
See More
Product Features:
- Pre-programmed replacement – this fuel pump driver module for GM vehicles directly replaces the original and requires no programming for installation
- Upgraded design – module features enhanced microcontroller and new active electronic components for added reliability
- Durable construction – module housing is thermal- and vibration-tested, with a powder-coated aluminum backing plate for corrosion resistance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Dorman – Fuel Sending Unit Pigtail (Part No.645-221)
from
$52.99
This fuel sender connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this fuel sender connector matches the appearance and function of the factory hardware on specified applications.
- Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Carquest Premium – Air Suspension Compressor Motor Connector (Part No.PTC1308)
from
$49.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
Product Features:
See More
Product Features:
- Premium quality materials for longer service life
- Sealed connections (where applicable) to prevent environmental corrosion and performance issues
- Global coverage for import and/or domestic applications
- OE specified wire gauge to ensure a reliable electrical connection
- Designed to meet or exceed OE specifications in form, fit and function
Carquest Premium – Fuel Cap Tester Adapter (Part No.12422)
from
$39.99
Fuel Cap Tester Adaper for use with Stant fuel cap testers. Color coded for easy identification. Made of durable plastic.
Product Features:
See More
Product Features:
- BAR Certified adapters
- Adapter check’s a fuel cap’s ability to hold pressure.
- Adapters meet EPA standards for recommended fleet coverage.
- Check adapter application chart for specific makes and models
Top-Rated Fuel and Emissions Systems Brands For Your 2008 Cadillac Escalade ESV
Shop for the best-rated brands offering Fuel and Emissions Systems and other products for your 2008 Cadillac Escalade ESVs. Below you’ll find some of our best rated Fuel and Emissions Systems from FELPRO, Carquest Premium, and Dorman, and more. Fuel and Emissions Systems from these brands that fit a 2008 Escalade ESV start at just $2.29 and are rated as high as 4.6 stars. OEM and aftermarket Fuel and Emissions Systems don’t get more top quality, durable, and affordable than from the brands below.
Popular FELPRO 2008 Cadillac Escalade ESV Fuel and Emissions Systems
When it comes to maintaining or upgrading your 2008 Cadillac Escalade ESV, using quality Fuel and Emissions Systems is essential to ensure durability and a perfect fit. FELPRO ticks all of those boxes. We offer a wide selection of FELPRO Fuel and Emissions Systems, specifically designed for the 2008 Cadillac Escalade ESV. With over 3 FELPRO brand Fuel and Emissions Systems in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $2.29, with an average price of just $8.42. Plus, with over 18 customer reviews and an average rating of 4.6 stars, you can trust that our FELPRO Fuel and Emissions Systems will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$8.99
(14)
Fuel Injector O-Ring Kit
“I rebuilt my engine using a off-brand gasket kit. The O-rings that came with the kit did not fit right. I bought these from Advance. They were Felp”
from
$2.29
(1)
Exhaust Gas Recirculation (EGR) Valve Gasket
“Installed on my 99 Silverado Z71. Perfect fit and good price.”
Popular Carquest Premium 2008 Cadillac Escalade ESV Fuel and Emissions Systems
Carquest Premium auto parts is one of the highest quality Fuel and Emissions System brands in the market. Any 2008 Cadillac Escalade ESV owner should feel confident when installing genuine Carquest Premium parts in their vehicle. To ensure the best fit and performance for your 2008 Escalade ESV, Advance Auto Parts carries a full inventory of 3 Carquest Premium Fuel and Emissions Systems. Plus you will be keeping your Cadillac in peak condition while saving money because prices on these Carquest Premium Fuel and Emissions Systems range from $15.99 to $65.99, plus, with more than 7 customer reviews and an impressive 4.4 stars average rating, you can be confident the Fram Fuel and Emissions Systems below will deliver on both quality and value.
from
$65.99
(1)
Mass Air Flow Sensor (MAF) – 100% NEW
“Your team was very helpful and was able to get my car back on the road within an hour!!!”
from
$15.99
(5)
Fuel Tank Lock Ring LO1582926
“Seems like a nice quality part, installed nice, no complaints.”
FAQs for 2008 Cadillac Escalade ESV Fuel and Emissions Systems
Which Fuel and Emissions Systems are best-sellers for 2008 Cadillac Escalade ESVs?
Out of 106 Fuel and Emissions Systems that fit 2008 Cadillac Escalade ESVs, the following parts are the top sellers:
- Fuel Cap: 10841, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (10049294) – $21.79
- Oxygen Sensor: 4 Wire, 24.02" Long, Heated, Universal (19370039) – $77.99
- Vapor Canister Purge Valve (18057381) – $60.99
What’s the price range for 2008 Cadillac Escalade ESV Fuel and Emissions Systems?
Fuel and Emissions System prices for the 2008 Cadillac Escalade ESV start at $1.79 and go up to $419.99 for the most premium parts.
What’s the average price of a Fuel and Emissions System for a 2008 Cadillac Escalade ESV?
The average price for Fuel and Emissions Systems for the 2008 Cadillac Escalade ESV is $80.10. Keep in mind the variety of part types within our Fuel and Emissions System category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Fuel and Emissions Systems for other Cadillac Escalade ESV model years?
What are the cheapest Fuel and Emissions Systems for my 2008 Cadillac Escalade ESV?
The cheapest 2008 Cadillac Escalade ESV Fuel and Emissions Systems we carry in stock are:
- Exhaust Gas Recirculation (EGR) Valve Gasket (15780617) – $1.79
- Exhaust Gas Recirculation (EGR) Valve Gasket (15780238) – $2.29
- Exhaust Gas Recirculation (EGR) Valve Gasket (15780239) – $2.79
- Fuel Pressure Relief Valve Cap (12044334) – $6.29
- Fuel Line Retaining Clip (17191034) – $6.99
What are the top-rated Fuel and Emissions Systems that fit the 2008 Cadillac Escalade ESV?
Out of 1,668 reviews by customers, our 2008 Cadillac Escalade ESV Fuel and Emissions Systems have an average customer rating of . These are some of the highest-rated Fuel and Emissions System types for the 2008 Cadillac Escalade ESV and their top-rated products:
- Vapor Canister Purge Valves
- Vapor Canister Purge Valve (18057381) – $60.99
- Air Flow Sensors
- Vapor Canister Purge Valve (18057381) – $60.99
- Oxygen Sensors
- Vapor Canister Purge Valve (18057381) – $60.99
What types of Fuel and Emissions Systems do you sell for my 2008 Cadillac Escalade ESV?
As of 4/10/25, these are some of the most in-demand types of Fuel and Emissions Systems for a 2008 Cadillac Escalade ESV:
Can I get help with 2008 Cadillac Escalade ESV Fuel and Emissions System orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Cadillac Fuel and Emissions Systems and more.
What is your return policy for Cadillac Escalade ESV Fuel and Emissions Systems?
Advance Auto Parts keeps returns simple. For new Cadillac Escalade ESV Fuel and Emissions Systems and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
