from

$144.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Toyota Tacoma and T100 without factory locking differential
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$399.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Toyota Tacoma and T100 without factory locking differential
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$107.99

When the thin-gauge steel corrodes on Sequoia, Tacoma, Tundra truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.

Product Features:

Rear Differential Cover
Rear Differential Cover
When the thin-gauge steel corrodes on Sequoia, Tacoma, Tundra truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.
Direct replacement – this weld-on differential cover directly replaces a corroded original cover on certain Sequoia, Tacoma and Tundra trucks
Cost-effective repair – rather than buy a new axle, cut off the old cover and weld on this new one

from

$8.51

Axle Seal

from

$16.99

Toyota T100 & Tacoma crush sleeve. Approx 2.325″ long.

Product Features:

Crush sleeve for Toyota Tacoma and T100 without factory locker
2.235″ tall

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$1044.99

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.

Product Features:

Pre-Pressed Rear Axle
Pre-Pressed Rear Axle
Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.
Easier installation – this loaded axle assembly includes a pre-assembled new axle shaft, wheel bearing, hub and backing plate
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components

from

$246.99

Yukon yoke for ’04 and newer Toyota T100 and Tacoma (without locker) with 30 spline. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 2005 and up Toyota Tacoma and T100
30 spline
66mm x 66mm bolt pattern

from

$18.99

Product Features:

Side gear thrust washer
Fits Toyota Tacoma and T100

from

$669.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 7.5″
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$15.99

Toyota T100 & Tacoma pinion nut.

Product Features:

Pinion nut
Fits Toyota Tacoma and T100 without factory locking differential

from

$42.99

Product Features:

TOYOTA 8″ V6&4CLY TURBO

from

$759.99

Differential

from

$21.99

Product Features:

KIT SHIM SIDE 9.5″ GM

from

$120.81

Differential Pinion

from

$126.99

Bearing race driver front Toyota 7.5″, 8″, Landcruiser, and the Suzuki Samurai. No return. (TOY30306).

Product Features:

Bearing race driver
Fits 30306 race
All steel construction

from

$73.99

Product Features:

Cross pin shaft
Fits Toyota Tacoma and T100

from

$30.99

Product Features:

Pinion gear thrust washer
Fits Toyota Tacoma and T100

from

$364.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits reverse rotation Toyota 7.5″
7.500″ ring gear diameter
23 spline pinion
10 ring gear bolts
4.56 ratio

from

$9.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$101.99

7.5″ V6 & 4cyl side shim kit (incl. 7 shims).

Product Features:

Carrier shim kit
Fits Toyota 7.5″

from

$7.99

07 & up Tundra & Sequoia front ring gear bolt..

Product Features:

Ring gear bolt
Fits 2007 and up Toyota Tundra front

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$13.49

Product Features:

KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

from

$27.99

Pinion preload shim for Toyota T100. One single shim. 0.033″ thick. Two needed. Fits against crush sleeve.

Product Features:

Fits Toyota T100 and Tacoma
0.140″ thick

from

$469.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Toyota Tacoma and T100 rear without factory locking differential
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and silicone.

from

$479.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits Toyota Tacoma and T100 rear without factory locking differential
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.