2007 Mazda B4000 Drivetrains

Below you will find various in-demand Mazda Drivetrains, components and accessories for your 2007 B4000. Advance Auto Parts has popular B4000 parts like Transfer Cases, Spindles, Drive Shafts and Axles and more. You’ll also find aftermarket and OEM Drivetrains for other B4000 model years including 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2008, 2009 and more. Select a category of 2007 Mazda B4000 Drivetrains below and start saving instantly.

Popular 2007 Mazda B4000 Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Pinion Shaft Bearings

U-Joints

Drive Shaft and Axles

Transmission Transfer Case Motors

Transfer Case Adapter Gaskets

Transfer Case Gaskets

Rear Differential Cover Gaskets

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Differential Cover Bolts

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Disc Kits

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Ring and Pinions

Differential End Yokes

Spindle Lock Nuts

Drive Shaft Repair Kits

Differential Lock Assemblies

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Differential Lock Springs

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Drive Shaft Seals

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Axle U-Bolt Kits

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Auxiliary Shaft Bearings

Axle Shaft Snap Rings

Spindle Washers

Differential Ring and Pinion Kits

Drive Axle Assemblies

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Drive Motor Battery Pack Coolant Temp Sensor

Essential Drivetrains for 2007 Mazda B4000s

from

$199.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits AMC Model 35 IFS
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$26.99

Spindle nut for Dana 28 & Model 35IFS front for manual locking hub conversion. This replaces Spicer part number 43749.

Product Features:

Spindle nut
Fits Dana Spicer 28 and AMC Model 35 IFS
For manual locking hub conversion

from

$444.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$371.99

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$9.99

7.5″ Ford cover gasket.

Product Features:

Cover gasket
Fits Ford 7.5″

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$15.99

Driveworks wheel bearings are a direct replacement for original parts at a much more affordable cost. Each wheel bearing is engineered to meet or exceed OE specifications, and goes through intensive quality control inspections to ensure proper fitment. Manufactured using high-precision machinery and advanced heat treatment processes, these bearings are designed for maximum durability and extended periods of use under any driving condition. Specific to certain applications, Driveworks bearings have multi-lip seals built into the bearing for increased protection against invasive contaminants and premature wear.

Product Features:

Depending on the application, specified Driveworks wheel bearings have integrated encoder rings that automatically sync with the vehicle’s anti-lock braking system (ABS) upon successful installation
Engineered, manufactured, and tested to meet or exceed OE specifications
Integrated seal design improves contamination resistance for a longer bearing life
High performance grease is used to lubricate the inner raceway to ensure smooth operation, higher operating temperatures, and minimal noise
Manufactured from high quality steel to maximize durability under even the harshest driving conditions
Brand may vary by location

from

$134.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Ford 8.8″
Includes carrier bearings and races and “super” carrier shim kit

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$36.99

Un-notched cross pin shaft for 7.5″ Ford. OEM, not Auburn gear.

Product Features:

Cross pin shaft for Ford 7.5″
3.45 and down ratios only

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$586.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$4.99

Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 INside axle snap ring (next to side gear).

Product Features:

Inner axle snap ring for Dana Spicer 28, 30, 44 and 50
Intalls next to side gear

from

$209.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 31 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$59.99

Product Features:

Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
Interlocking design makes installation much easier

from

$3.99

Product Features:

Outer slinger
Fits Dana Spicer 28

from

$74.99

Chrome cover for 8.8″ Ford.

Product Features:

Fits Ford 8.8″
Chrome

from

$218.99

Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 8.8″ with 28 spline axles
Provides 100% traction to both wheels at all times
Installs into standard open carrier case

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$262.99

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles
Quality materials – all components are built for reliable longevity and performance
Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
Trustworthy quality – backed by team of designers and engineers in the United States

from

$37.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$399.99

Product Features:

Dura Grip positraction carrier case
Does not include spider gears
Fits Ford 8.8″ with 28 spline axles

from

$49.99

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$18.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$329.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits AMC Model 35 IFS
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$1599.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$42.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

Upgrade your 2007 Mazda B4000 with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2007 Mazda B4000, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Mazda or enhancing its overall performance, Drivetrains are key to keeping your B4000 functioning at its best. At Advance Auto Parts, we offer a wide selection of 294 Drivetrains for the 2007 Mazda B4000, designed to meet your needs without breaking the bank. From Transfer Case replacements to Spindles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2007 Mazda B4000 at great prices. Our Drivetrains inventory for this model ranges from just $1.29 to $2,064.99, with an average price of $251.94. Our 294 Drivetrains in stock come from 22 trusted brands, so you’re sure to find the right part for your 2007 Mazda B4000 without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2007 Mazda B4000, we stock popular OEM and aftermarket Drivetrains from top names like Spicer, National, Dorman, and more. Spicer Drivetrains start at just $31.99 and boast an impressive 4.6 stars average rating from customers. National and Dorman also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4.3 stars rating. With 1,843 customer reviews and counting, our 2007 Mazda B4000 Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2007 Mazda B4000 is always ready to roll. We’re committed to providing you with everything you need to keep your B4000 in top shape, all in one place. Start shopping confidently below for your 2007 Mazda B4000!

Best-Selling Transfer Cases for 2007 Mazda B4000s

Enhance the driving experience in your Mazda with 9 quality Transfer Case components, starting at $7.49.

show more show less

from

$10.79

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$26.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific, providing unsurpassed quality for a seal you can trust
Validated for fit, form, and function
Engineered for the sealing repair environment
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$137.99

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
100% new – this transfer case motor is entirely new, not remanufactured like competitors
Quality assured – vehicle-specific application has been validation tested to ensure quality

from

$7.49

Product Features:

Brand may vary by location

from

$104.99

TCaseBrg-SealKit

from

$62.99

The FAG repair sleeve is a precision element that provides additional sealing for damaged shafts. Made of heat-treated stainless steel, the FAG repair sleeve signifcantly increases the life of the shaft and prevents premature wear. Since no shaft removal or machining is required during the repair, the repair sleeve is a cost effective repair solution to protect damaged surfaces.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$18.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications
Effective fix – restores a tight seal in the transfer case after original gasket fails
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$10.49

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Most Popular 2007 Mazda B4000 Spindles

Customize your Mazda with 8 Spindles products like Spindle Lock Nuts, Spindle Retainers, and Spindle Lock Nut Thrust Washers, all priced under $26.99.

show more show less

from

$3.49

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.49

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.99

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$3.99

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.99

Spindle nut for Dana 28 & Model 35IFS front for manual locking hub conversion. This replaces Spicer part number 43749.

Product Features:

Spindle nut
Fits Dana Spicer 28 and AMC Model 35 IFS
For manual locking hub conversion

from

$8.99

Spindle nut washer for Dana 28 & Model 35IFS front for manual locking hub conversion. This replaces Spicer part number 36569.

Product Features:

Spindle nut washer for Dana Spicer 28 and AMC Model 35 IFS
For manual locking hub conversion

Top Picks for 2007 Mazda B4000 Drive Shafts and Axles

Upgrade Mazda B4000s with top-quality Drive Shafts and Axles parts, including 43 OEM and aftermarket selections for your 2007 model.

show more show less

from

$7.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$31.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$38.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$13.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$22.99

Manufactured with premium-grade steel, National® cylindrical bearings are designed and engineered to meet OE specifications.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$10.99

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$28.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$119.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$113.99

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$19.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$18.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$15.99

Depending on the application, specified Driveworks wheel bearings have integrated encoder rings that automatically sync with the vehicle’s anti-lock braking system (ABS) upon successful installation
Engineered, manufactured, and tested to meet or exceed OE specifications
Integrated seal design improves contamination resistance for a longer bearing life
High performance grease is used to lubricate the inner raceway to ensure smooth operation, higher operating temperatures, and minimal noise
Manufactured from high quality steel to maximize durability under even the harshest driving conditions
Brand may vary by location

from

$42.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.250″ O.D.
1.400″ I.D.

from

$52.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1559TV axle bearing and seal kit, TorringtonBrand, 2.530″ OD, 1.620″ ID This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.530″ O.D.
1.620″ I.D.

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$23.49

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.49

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.99

Axle seal, for 1559 OR 6408 bearing, NOT COARSE spline 12T.Yukon Mighty seal.

Product Features:

Rear axle seal
2.530″ O.D.

from

$59.99

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$361.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100 percent dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100 percent NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100 percent dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.
Measurement Method: Measurement is taken from the CV face to the centerline of the furthest U-Joint on the opposite end of the collapsed Prop Shaft.

from

$4.99

Dana 28 (93^) & Model 35 outer axle/hub snap ring.

Product Features:

Outer axle snap ring for AMC Model 35 IFS and 1993 and up Dana Spicer 28

from

$8.99

Ford 7.5″ C/clip, TracLoc & standard Open.

Product Features:

c-clip for Ford 7.5″
Fits standard open and Trac Loc applications
Not compatible with Auburn Gear positraction

from

$4.99

Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 INside axle snap ring (next to side gear).

Product Features:

Inner axle snap ring for Dana Spicer 28, 30, 44 and 50
Intalls next to side gear

from

$17.79

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

In-Demand Universal Joints for 2007 Mazda B4000s

Select from 24 premium Universal Joints parts for your 2007 Mazda B4000, with prices ranging from $4.49 to $111.99.

show more show less

from

$8.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 354, 369 & 437G
Contains two 1.59″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$42.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$35.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$31.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$33.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$46.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$7.89

Universal Joint

from

$6.49

Universal Joint

from

$4.59

Universal Joint

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$5.49

Universal Joint – Brute Force

from

$4.49

Universal Joint

from

$40.99

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$73.99

Yukon Small 260 axle U/Joint for early Dana front axles. 2.188″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$44.99

from

$36.99

from

$22.49

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

Most Sold 2007 Mazda B4000 Differentials

Explore our best-selling Mazda parts for the 2007 B4000 among 209 OEM and aftermarket options starting from $1.29.

show more show less

from

$7.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.29

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$65.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$444.99

from

$179.99

Product Features:

FRD 10BL 8.8 R/P 4.10A MG

from

$15.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$41.99

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$16.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$27.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$137.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

MASTER KIT FORD 8.8″

from

$6.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$169.99

The National bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION – Includes everything needed to complete the repair
STRONG AND DURABLE – Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Professional technicians know they can depend on National

from

$19.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$112.99

The National bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION – Includes everything needed to complete the repair
STRONG AND DURABLE – Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Professional technicians know they can depend on National

from

$8.99

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$5.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$37.99

DIFF COVER KIT

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$17.49

Product Features:

Brand may vary by location

from

$10.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$37.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$24.49

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Top-Rated Drivetrains Brands For Your 2007 Mazda B4000

Shop for the best-rated brands offering Drivetrains and other products for your 2007 Mazda B4000s. Below you’ll find some of our best rated Drivetrains from Spicer, National, and Dorman, and more. Drivetrains from these brands that fit a 2007 B4000 start at just $3.49 and are rated as high as 4.6 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Spicer 2007 Mazda B4000 Drivetrains

When it comes to maintaining or upgrading your 2007 Mazda B4000, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 2007 Mazda B4000. With over 3 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $31.99, with an average price of just $37.99. Plus, with over 19 customer reviews and an average rating of 4.6 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $31.99

(12)

Universal Joint, Greaseable 1310 Series OSR

“No problems with Installation and appears to be quality part! Great for my old School Street Car!”

from $42.99

(5)

Universal Joint, Greaseable 1330 Series OSR

“I changed my Ford Expedition’s stock non greaseable universal joints at 213K miles. There was noticeable vibration. The Spicers fit well and have t”

from $38.99

(2)

Universal Joint

“I use this on a 4×4 off-road. It’s always a tough trade-off between the greaseable and non-greasable u-joints. The non-greaseable is stronger. The”

Popular National 2007 Mazda B4000 Drivetrains

National auto parts is one of the highest quality Drivetrain brands in the market. Any 2007 Mazda B4000 owner should feel confident when installing genuine National parts in their vehicle. To ensure the best fit and performance for your 2007 B4000, Advance Auto Parts carries a full inventory of 3 National Drivetrains. Plus you will be keeping your Mazda in peak condition while saving money because prices on these National Drivetrains range from $7.99 to $13.99, plus, with more than 15 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $9.29

(2)

Bearing Race

“Reasonable price and woks well. front diff 2006 Escalade esv”

from $13.99

(9)

Bearing

“as advertised”

from $7.99

(4)

Bearing Race

“Goes with M88010 bearing cup. Application was the pinion bearing race for a Ford 9 Inch on a 1957 Ford F-100.”

FAQs for 2007 Mazda B4000 Drivetrains

Which Drivetrains are best-sellers for 2007 Mazda B4000s?

Out of 294 Drivetrains that fit 2007 Mazda B4000s, the following parts are the top sellers:

Axle Housing Cover Gasket Rectangular Shaped, 10 Bolt Hole Gasket (5782406) – $15.99
Universal Joint (10265714) – $15.99
Universal Joint (10265720) – $31.99

What’s the price range for 2007 Mazda B4000 Drivetrains?

Drivetrain prices for the 2007 Mazda B4000 start at $1.29 and go up to $2,064.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2007 Mazda B4000?

The average price for Drivetrains for the 2007 Mazda B4000 is $251.94. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Mazda B4000 model years?

Yes, we currently carry Drivetrains for 14 model years of Mazda B4000s between 1994 and 2009. Drivetrains are bought most frequently for the following model years: 2009, 2008, 2006, 2005, 2004, 2003, 2002, 2001, and 2000.

What are the cheapest Drivetrains for my 2007 Mazda B4000?

The cheapest 2007 Mazda B4000 Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282257) – $1.29
Ring Gear Bolt (20520509) – $1.99
Differential Cross Shaft (10282201) – $2.99
Differential Crush Sleeve (10282338) – $2.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49

What are the top-rated Drivetrains that fit the 2007 Mazda B4000?

Out of 1,843 reviews by customers, our 2007 Mazda B4000 Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 2007 Mazda B4000 and their top-rated products:

Universal Joints
- Universal Joint Strap Kit (10086955) – $8.99
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Greaseable Super Strength Universal Joint (10086944) – $46.99
Spindles
- Universal Joint Strap Kit (10086955) – $8.99
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Greaseable Super Strength Universal Joint (10086944) – $46.99
Differentials
- Universal Joint Strap Kit (10086955) – $8.99
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Greaseable Super Strength Universal Joint (10086944) – $46.99

What types of Drivetrains do you sell for my 2007 Mazda B4000?

As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 2007 Mazda B4000:

Can I get help with 2007 Mazda B4000 Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Mazda Drivetrains and more.

What is your return policy for Mazda B4000 Drivetrains?

Advance Auto Parts keeps returns simple. For new Mazda B4000 Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2007 Mazda B4000 Drivetrains

Yukon Gear – Pinion Install Kit For Model 35 IFS Differential For Explorer And Ranger (Part No.13084)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Yukon Gear – Spindle Nut For Dana 28 & Model 35IFS Front For Manual Locking Hub Conversion (Part No.33490)

Powertrax – Lock Right Locker (Part No.1830-LR)

Powertrax – Lock Right Locker (Part No.1822-LR)

Yukon Gear – 7.5" Ford Cover Gasket (Part No.23009)

Yukon Gear – Bearing Race Driver (Part No.56020)

Driveworks – Wheel Bearing: Direct Fit, 1 Piece (Part No.S-5707)

Yukon Gear – Carrier Installation Kit For Ford 8.8" Differential (Part No.57007)

National – Bearing (Part No.M88048)

Yukon Gear – Un-Notched Cross Pin Shaft For 7.5" Ford – Oem, Not Auburn Gear (Part No.33330)

Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)

Dorman – Drive Shaft: Greaseable, Adjustable (Part No.938-183)

Yukon Gear – Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 Inside Axle Snap Ring (Next To Side Gear) (Part No.33268)

USA Standard Gear – Standard Spider Gear Set For Ford 8.8", 31 Spline (Part No.39016)

Yukon Gear – Super Carrier Shim Kit For Ford 7.5", GM 7.5", 8.2" & 8.5" (Part No.55001)

Yukon Gear – Replacement Outer Slinger For Dana 28 (Part No.33016)

Yukon Gear – Chrome Cover For 8.8" Ford (Part No.32009)

Yukon Gear – Mini Spool For Ford 8.8" With 28 Spline Axles (Part No.32225)

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Dorman – Differential Clutch Kit (Part No.697-780)

National – Shaft Repair Sleeve (Part No.99181)

Yukon Gear – Dura Grip Case For Ford 8.8", 28 Spline (Part No.20072)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-984)

Dorman – Transfer Case Gasket (Part No.926-476)

USA Standard Gear – Master Overhaul Kit for the Model 35 IFS Front Differential (Part No.37068)

Spartan – Drive Axle Assembly; Ford Ranger 99-09 Axle (Part No.RAX1931K)

Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)

National – Multi-Purpose Seal (Part No.710403)

Driveworks – Taper Bearing Cone (Part No.S-M-88048)

Felpro – Transfer Case Adapter Gasket (Part No.55484)

Dorman – Transfer Case Shift Motor (Part No.600-929)

Driveworks – Transfer Case Input Shaft Seal (Part No.S-710403)

USA Standard Gear – TCaseBrg-SealKit (Part No.78350)

FAG US – Repair Sleeve (Part No.SR3501)

Dorman – Transfer Case Gasket (Part No.926-476)

FAG US – Bearing Cone (Part No.KLM11949)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (Part No.615-072.1)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Part No.615-073.1)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Sold by each) (Part No.615-073)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Sold by each) (Part No.618-033)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (Part No.615-072)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-033.1)

Yukon Gear – Spindle Nut For Dana 28 & Model 35IFS Front For Manual Locking Hub Conversion (Part No.33490)

Yukon Gear – Spindle Nut Washer For Dana 28 & Model 35IFS Front For Manual Locking Hub Conversion (Part No.33483)

Driveworks – Oil Seal (Part No.S-8660S)

Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)

Spicer – Universal Joint (Part No.5-1310X)

National – Bearing (Part No.M88048)

National – Wheel Bearing (Part No.5707)

National – Wheel Seal (Part No.8660S)

National – Multi-Purpose Seal (Part No.710428)

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV11110)

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV11109)

National – Drive Axle Shaft Seal (Part No.710429)

Driveworks – Axle Repair Bearing (Part No.S-RP-5707)

Driveworks – Wheel Bearing: Direct Fit, 1 Piece (Part No.S-5707)

Yukon Gear – R1563Tav Rear Axle Bearing And Seal Kit (Part No.10004)

Yukon Gear – R1559Tv Rear Axle Bearing And Seal Kit (Part No.10001)

Yukon Gear – C/Clip (Part No.33083)

National – Multi-Purpose Bearing (Part No.206)

National – Multi Purpose Seal (Part No.1981)

Yukon Gear – Axle Seal, For 1559 Or 6408 Bearing (Part No.30201)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-988)

Cardone – Drive Shaft: Greasable, Direct Replacement (Part No.65-9293)

Yukon Gear – Dana 28 (93^) & Model 35 Outer Axle/Hub Snap Ring (Part No.33269)

Yukon Gear – Ford 7.5" C/Clip, Tracloc & Standard Open (Part No.33080)

Yukon Gear – Dana 28, Dana 30, Model 35-Reverse, Dana 44, Dana 50 Inside Axle Snap Ring (Next To Side Gear) (Part No.33268)

National – Multi-Purpose Bearing (Part No.S-268)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.437-10)

Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

Driveworks – Universal Joint (Part No.DW-354)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Driveworks – Universal Joint (Part No.DW-369)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)