2007 Isuzu Ascender Differentials

Find your specific 2007 Isuzu Ascender original or aftermarket Differentials below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.

Essential 2007 Isuzu Ascender Differentials

from

$232.99

Yukon standard open carrier case for ’00-’06 GM 8.6″, V2 – version 2 design.

Product Features:

Fits 2000-2006 GM 8.6″ with open differential

from

$234.99

Yukon cast yoke for GM 8.5″ with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$101.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (includes Supershims)

Product Features:

Fits GM 8.6″
Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2008 and down GM 8.6″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$1839.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$239.99

Yukon standard open spider gear kit for GM 7.6″ front, 28 spline. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 7.6″ IFS open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$103.99

The National® bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION — Includes everything needed to complete the repair
STRONG AND DURABLE — Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING¿-¿Comprehensive¿testing throughout design and development processes by National engineers for quality you can count on¿
RIGOROUS TESTING┐-┐Comprehensive┐testing throughout design and development processes by National engineers for quality you can count on┐
Professional technicians know they can depend on National

from

$57.99

Cross pin shaft for 7.5″, 7.625″, and 8″ GM.

Product Features:

Cross pin shaft for GM 7.5″, 7.625″ and 8.0″
Fits standard open differentials only

from

$344.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits GM 7.5″ and 7.6″
7.50″ ring gear diameter
27 spline pinion
10 ring gear bolts
3.42 ratio

from

$26.99

Product Features:

Brand may vary by location

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$221.99

from

$11.29

SHAFT SEAL

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$7.99

Differential Cover B

from

$929.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit has larger bearing journals for added strength & uses heavy-duty carrier bearings & races.

Product Features:

Fits GM 8.5″ and 8.6″ with 30 spline axles
2.73 ratio and up only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$25.99

Yukon 4340 Chrome-Moly replacement outer stub for D44 ’87-’94 Wrangler with a length of 8.31″ and 27 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

27 spline
8.31″ long
Fits Dana Spicer 30 in 1987-1994 Wrangler
Outer stub
5-760X U-joint size
4340 Chromoly
For WARN hub conversion only

from

$10.99

8.5″ & 8.6″ GM standard Open pinion gear Thrust washer. also fits 8.5″ Eaton with 0.795″ cross pin.

Product Features:

Pinion gear thrust washer for GM 8.5″ and 8.6″
Fits standard open differentials only
0.795″ I.D.

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$39.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

Popular 2007 Isuzu Ascender Differentials Categories

Differential Oil

Rear Differential Cover Gaskets

Differential Covers

Differential Pinion Shaft Lock Bolts

Differential Bearings

Differential Pinion Pilot Bearings

Differential Cover Bolts

Differential Carriers

Differential Bearing Kits

Front Differential Pinion Bearings

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Clutch Packs

Differential Ring and Pinions

Differential End Yokes

Differential Lock Assemblies

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Rear Housing Cover Gaskets

Differential Pinion Bearing Kits

Differential Seals

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Differential Carrier Bearing Shims

Differential Crush Sleeves

Pinion Shaft Seals

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Differential Pinion Gear Washers

Limited Slip Differential Assemblies

Differential Clutch Pack Clips

Maybe you’re in the middle of a full rebuild of that 2007 Isuzu Ascender. Maybe you just need a couple of Differentials. Either way, Advance Auto Parts has 189 different Differentials in our inventory ranging from $2.49 to $1,839.99. That means you can find the exact parts or products you need to keep that 2007 Isuzu Ascender running smoothly.

Differentials are only as good as their brand. We stock 13 different brands to make sure you have plenty of trusted parts to choose from for your 2007 Isuzu Ascender. FELPRO, Valvoline, and Driveworks are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Differentials for your 2007 Isuzu Ascender, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 317 reviews in this category, some of the top rated parts include Multi Purpose Seal with 3.9 stars and Axle Differential Bearing and Seal Kit with 4.5 stars.

So if you’re in the market for aftermarket Differentials to keep your 2007 Isuzu Ascender rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Differentials Brands To Make Your 2007 Isuzu Ascender Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 2007 Isuzu Ascender demands trusted brand parts and products to keep it running. Many trusted brands of Differentials make up Advance Auto Parts’ inventory, and all are ready to help make your Ascender the best it can be. Be sure to browse some of our top Differentials brands and parts.

Popular Felpro Differentials

We carry Felpro parts in our stock across Rear Housing Cover Gaskets and Rear Differential Cover Gaskets categories, plus more. For a 2007 Isuzu Ascender, our most popular Felpro Differentials include:

from $41.99

(4)

Differential Cover Gasket

Rear Housing Cover Gaskets

from $9.99

(195)

Differential Cover Gasket

Rear Differential Cover Gaskets

FAQs for 2007 Isuzu Ascender Differentials

What are the most purchased Differentials for the 2007 Isuzu Ascender?

Out of 189 Differentials for the 2007 Isuzu Ascender, the most popular in our inventory are:

from $14.99

(36)

Transfer Case Fluid, 1 Quart

Differential Oil

from $10.79

(33)

Taper Bearing Set

Differential Bearings

from $57.99

This product is not rated

3 Qt – 80W90 Conventional Gear Oil With Posi Additive

Differential Oil

What are the top-rated 2007 Isuzu Ascender Differentials?

Top-rated Differentials for your 2007 Isuzu Ascender based on customer reviews/ratings are:

from $16.99

(14)

Multi Purpose Seal

“correct part easy to install”

from $103.99

(8)

Axle Differential Bearing and Seal Kit

“got exactly what i ordered. thanks.”

from $23.99

(7)

Bearings

“Good price”

2007 Isuzu Ascender Differentials

More 2007 Isuzu Ascender Differentials

Essential 2007 Isuzu Ascender Differentials

Yukon Gear – Standard Open Carrier Case For ’00-’06 GM 8.6" V2 Design (Part No.20096)

Yukon Gear – Cast Yoke For GM 8.5" With A 1350 U/Joint Size (Part No.41092)

Yukon Gear – Minor Install Kit For GM 8.6" Rear Differential (Part No.12059)

Yukon Gear – Cross Pin Bolt (Part No.33067)

Yukon Gear – Pinion Install Kit For ’08 & Down GM 8.6" Differential (Part No.13073)

Spartan – Drive Axle Assembly; GM SUV 06-09 Axle (Part No.RAX2118D)

Yukon Gear – Standard Open Spider Gear Kit For GM 7.6" Front, 28 Spline (Part No.16121)

National – Axle Differential Bearing and Seal Kit (Part No.RA-321-C)

Yukon Gear – Cross Pin Shaft For 7.5", 7.625", And 8" GM (Part No.33404)

USA Standard Gear – Ring & Pinion Gear Set For GM 7.5" In A 3.42 Ratio (Part No.36195)

Driveworks – Differential Pinion Seal (Part No.S-710474)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Yukon Gear – Pinion Depth Shims For GM 8.25" IFS, 8.5", 12 Bolt Car, Ford 8.8" & Chrysler 8.25" (Part No.55009)

Motive Gear – Pinion Nut (Part No.1260823)

National – Bearings (Part No.M86610)

Yukon Gear – Bearing Race Driver (Part No.56020)

Motive Gear – Differential Carrier (Part No.GM8.6L)

FAG US – SHAFT SEAL (Part No.SS2685)

Yukon Gear – 8.5" & 8.2" GM Carrier Installation Kit (Part No.57008)

Yukon Gear – Differential Cover B (Part No.33572)

Yukon Gear – Dura Grip Positraction For GM 8.5" & 8.6" With 30 Spline Axles (Part No.26016)

Yukon Gear – Adapter Sleeve Fro GM 7.2", 7.625" & 8.0" Yokes To Use Triple Lip Pinion Seal (Part No.41210)

Yukon Gear – 8.5" & 8.6" GM Standard Open Pinion Gear Thrust Washer – Also Fits 8.5" Eaton With 0.795" Cross Pin (Part No.33385)

Yukon Gear – Super Carrier Shim Kit For Ford 8.8", GM 12 Bolt Car & Truck, 8.6 & Vette (Part No.55002)

Yukon Gear – Pinion Nut Washer (Part No.33167)

National – Shaft Repair Sleeve (Part No.99139)

Popular 2007 Isuzu Ascender Differentials Categories