from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$13.99

8″ Ford pilot bearing retainer.

Product Features:

Pilot bearing retainer for Ford 8″

from

$336.99

Yukon positraction internals for 8.8″ Ford with 28 spline axles. This kit fits Yukon Gura Grip & Eaton positractions. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 8.8″ with Yukon Dura Grip positraction with 28 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$13.59

Product Features:

FORD 9″ CROSS PIN

from

$35.49

Product Features:

MINI INSTALL KIT FORD 7.5

from

$3.99

Trac Loc ring gear bolt washer for 8″ and 9″ Ford.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For Trac Loc positraction applications only

from

$41.99

Product Features:

Shim kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

from

$309.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$10.99

Standard Open & TracLoc pinion gear thrust washer for 7.5″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 7.5″

from

$5.99

0.260″ diameter cross pin roll pin for 8.75″ Chrysler, 8″, 9″ Ford, and Model 20 and 35.

Product Features:

Roll pin for Chrysler 8.75″, Ford 8″ and 9″, AMC Model 20 and Model 35
0.260″ diameter

from

$242.99

Yukon yoke for Ford 9″ with 28 spline pinion and a 1330 U/joint size. 5″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″
28 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.125″ cap diameter
U-bolt style

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$108.99

Product Features:

INTERN. 9″ OPEN 2 PIN FD 31SPL

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$588.99

RngPnn

from

$6.99

Side gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

Side gear thrust washer for Ford 8.8″
0.750″ diameter cross pin shaft applications only

from

$241.99

8.8″ Ford TracLoc (with short ears–for late models only) clutch set, both sides.

Product Features:

Clutch kit
Fit Ford 8.8″ Trac Loc positraction

from

$294.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ with Daytona pinion support
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$74.99

1.250″ pinion adaptor sleeve (stock pinion into large support).

Product Features:

Adapter sleeve
Fits Ford 9″
Adapts 28 spline pinion into 35 spline pinion support

from

$487.99

Yukon Trac Loc internals for 8″ & 9″ Ford, 31 spline, includes hub & clutches. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 9″ with Trac Loc positraction with 31 spline axles
Includes two side gears, four pinion gears, cross pin shaft, clutch hub, roll pin and spider gear thrust washers.

from

$67.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in

Product Features:

Trac Loc spring
Fits Ford 7.5″

from

$148.99

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features:

AXLE SHAFT 8.8″ 28 SPL. 94 & UP MUSTANG W/ABS 29 15/16″ L&R

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$31.99

8″ Ford pinion shim kit.

Product Features:

Pinion depth shims for Ford 8″

from

$38.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National