2007 Ford Escape Ignition and Tune-Up Products

Essential 2007 Ford Escape Ignition and Tune-Up Products

Motorcraft – Ignition Coil: Meets or Exceeds Original Equipment Specifications, 1 Piece (Part No.DG-551)

Ignition Coil: Meets or Exceeds Original Equipment Specifications, 1 Piece

from

$84.99
The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles. Motorcraft and Ford Parts are used throughout Ford vehicles in a variety of applications that help ensure the proper build quality, integrity and long-lasting performance of every Ford car or truck. Motorcraft and Ford Parts are manufactured from first quality materials chosen specifically for maximum performance and application suitability. As with all Motorcraft and Ford Parts, any innovations or improvements developed since the vehicle’s manufacture are included in these after market replacement parts, ensuring the most current technology and performance.

Product Features:
  • These coils provide the exact spark timing that helps maximize the engine and emissions performance
  • RFI suppression helps minimize electronic noise through a Ford patented spring assembly inside the coil boot
  • Engineered to help withstand temperature extremes
  • Internal insulation displacement connection is helps make high-reliability internal connections
  • Interior insulation helps ensure no internal arcing
  • Right fit for each application; helps provide ease of installation and removal
  • High grade silicone rubber boot materials do not degrade or stick, aiding in environmental and dielectric sealing
  • Housings engineered to help resist cracking in the most extreme conditions
  • Ford-patented iron core lamination stack integrates rare earth magnets in the flux circuit to help deliver consistent high energy required for output
See More

Motorcraft – Motorcraft Central Ignition Coil (Part No.F3000384419MTR)

Motorcraft Central Ignition Coil

from

$130.28
Motorcraft ignition coils offer value without compromising quality. They are the right fit for Ford and Lincoln vehicles.

Product Features:
  • Helps ensure proper engine performance, maximize fuel economy, minimize both tailpipe emissions and RFI electronic interference
  • Helps avoid spark plug failure, drivability complaints, pre-ignition and detonation
  • Insulation provides multiple coats on the primary and secondary windings to ensure no internal arcing
  • Radio-Frequency Interference (RFI) Suppression
  • Magnets hold strength for the coil to maintain proper energy output
  • Steel used in the lamination stack to ensure a consistent magnetic field needed to develop the required voltage
  • Coil Housing is engineered to withstand extremes in temperature without cracking
See More

Carquest Premium – Ignition Switch Connector (Part No.PTC1725)

Ignition Switch Connector

from

$43.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:
  • Premium quality materials for longer service life
  • Sealed connections (where applicable) to prevent environmental corrosion and performance issues
  • Global coverage for import and/or domestic applications
  • OE specified wire gauge to ensure a reliable electrical connection
  • Designed to meet or exceed OE specifications in form, fit and function
See More

Carquest – Cornering Light Socket (Part No.PT189)

Cornering Light Socket

from

$23.29
BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:
  • Our control modules feature double wire bonds for better connections, greater dependability and longer life despite being subjected to intense vibration and the tough operating environment
  • Copper slug heat sinks provide better heat dissipation to prevent heat from damaging the module
  • Our ignition modules will respond to a weak signal from the crankshaft position sensor and begin energizing the coils immediately for better starts in cold weather
  • High-temperature polymer housing reducing moisture intrusion and minimizes vibration damage for extended life and improved reliability
  • Our ignition modules are durability tested for 500 thermal cycles ranging from -40C to +125C
See More

DENSO – Coil On Plug Boots-4 (Part No.671-4312)

Coil On Plug Boots-4

from

$46.99
DENSO First Time Fit COP boot sets are identical in form fit color and performance to the factory-installed boots. Every part of each COP boot set construction meets or exceeds OE/OES standards.

Product Features:
  • OE design ensures a tight boot seal that protects against moisture intrusion
  • High temperature resistant material provides greater protection against thermal overload
  • Stainless steel internal spring with resistor to suppress RFI and deliver maximum voltage to the plug
  • Engineered to the specifications used by the original vehicle manufacturer for an exact fit
See More

DENSO – Coil On Plug Boots-4 (Part No.671-4283)

Coil On Plug Boots-4

from

$36.99
DENSO First Time Fit COP boot sets are identical in form fit color and performance to the factory-installed boots. Every part of each COP boot set construction meets or exceeds OE/OES standards.

Product Features:
  • OE design ensures a tight boot seal that protects against moisture intrusion
  • High temperature resistant material provides greater protection against thermal overload
  • Stainless steel internal spring with resistor to suppress RFI and deliver maximum voltage to the plug
  • Engineered to the specifications used by the original vehicle manufacturer for an exact fit
See More

DENSO – Spark Plug Wire Set: Carbon Core, 4 Wire Set (Part No.671-4061)

Spark Plug Wire Set: Carbon Core, 4 Wire Set

from

$50.99
DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:
  • Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
  • Identical OE end caps are designed to “click” into place for easy installation and a secure fit
  • Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation
See More

Carquest Premium – Spark Plug Wire Set: 4 Wires, Increased performance, Designed for direct fit (Part No.35-4021)

Spark Plug Wire Set: 4 Wires, Increased performance, Designed for direct fit

from

$29.99
Product Features:
  • SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
  • Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
  • 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
  • EPDM inner insulation stops power-robbing voltage leaks.
  • With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
  • Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
  • Excellent interference suppression and consistent performance
  • Easy lock terminals for more convenient installation.
  • Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
  • Broad coverage available for most vehicles on the road today
  • Include grease pack to ensure easy installation and removal
See More

Motorcraft – Original Equipment Spark Plug Boot: No core (outer material Rubber) Core, Qty of 1 (Part No.WR-6134)

Original Equipment Spark Plug Boot: No core (outer material Rubber) Core, Qty of 1

from

$21.99
Motorcraft Plug Wires are Manufactured of premium-quality materials to strict Ford Engineering standards. High-Dielectric Insulation helps maintain and control voltage delivery while reducing Radio Frequency Interference. EPDM/Silicone wire jacket, spark plug & coil/ distributor insulators help protect against oil and high temperatures. Optimized wire lengths help minimize part numbers while still providing proper fit. Designed and Tested to Stringent Ford Standards.

Product Features:
  • Backed by Motorcraft’s Service Parts Warranty
  • Designed for long life – key life durability testing (equivalent to 10 years/150,000 miles) is conducted in addition to on-vehicle durability testing.
  • Optimized wire lengths help minimize part numbers while still providing proper fit.
  • Wires are optimum lengths for easy installation.
  • EPDM/Silicone wire jacket, spark plug AND coil / distributor insulators help protect against oil and high temperatures.
  • Motorcraft ignition components help prevent false check engine lights.
See More

Motorcraft – Direct Ignition Coil Boot (Part No.F3006429402MTR)

Direct Ignition Coil Boot

from

$18.78
The Motorcraft Direct Ignition Coil Boot is an OES replacement component that provides the same performance, durability, and service life as your factory original equipment.

Product Features:
  • OES replacement part for your vehicle’s original factory component
  • Offering the quality, reliability, and durability of OES
  • Manufactured to OES specification for fit, form, and function
See More

Carquest Premium – Coil On Plug Insulator Boot: Spring included, Designed for direct fit (Part No.35-7089)

Coil On Plug Insulator Boot: Spring included, Designed for direct fit

from

$7.49
CARQUEST Premium coil on plug boots are engineered to restore ignition boot reliability and performance. We have OE design providing an exact direct fit for your application and the performance and durability meet or exceed OE requirements. It offers excellent heat resistance as well as maximum protection against spark loss. With durable silicone compound for resistance to high heat or abrasion.

Product Features:
  • Provides excellent heat resistance as well as maximum protection against spark loss.
  • Durable silicone compound for resistance to high heat or abrasion
  • Spring included with the coil boot
  • Design for direct compatibility
  • OE design provides an exact fit for your application
  • Multipack provides one time replace all COP for better deal
See More

Carquest Premium – Coil On Plug Insulator Boot Multi Pack, Spring included (Part No.38-008FMP)

Coil On Plug Insulator Boot Multi Pack, Spring included

from

$35.99
CARQUEST Premium coil on plug boots are engineered to restore ignition boot reliability and performance. We have OE design providing an exact direct fit for your application and the performance and durability meet or exceed OE requirements. It offers excellent heat resistance as well as maximum protection against spark loss. With durable silicone compound for resistance to high heat or abrasion.

Product Features:
  • Provides excellent heat resistance as well as maximum protection against spark loss.
  • Durable silicone compound for resistance to high heat or abrasion
  • Spring included with the coil boot
  • Design for direct compatibility
  • OE design provides an exact fit for your application
  • Multipack provides one time replace all COP for better deal
See More

Motorcraft – Motorcraft Ignition Wire Set (Part No.F1020200737MTR)

Motorcraft Ignition Wire Set

from

$53.21
The Motorcraft Ignition wire set is a direct fit OEM replacement that guarantees the same performance and quality provided by the vehicle manufacturer.

Product Features:
  • OEM quality
  • OEM connectors for easy Installation.
  • Resistant to high temperatures, corrosion and vibration.
  • Ignition noise suppressed.
  • Reduces the chance of misfire
  • Increases engine life
  • Protects against wire set failure
See More

Carquest Premium – Ignition Knock (Detonation) Sensor (Part No.SBA3684)

Ignition Knock (Detonation) Sensor

from

$51.99
Carquest premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Carquest Premium – Premium Ignition Knock (Detonation) Sensor SBA6043 (Part No.SBA6043)

Premium Ignition Knock (Detonation) Sensor SBA6043

from

$66.99
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Product Features:
  • The Ignition Knock Sensor is a piezo chrystal type sensor that reports harmonics within the engine block as the result of unfavorable ignition in the combustion chamber. The engine control module will make ignition timing and fuel injection pulse adjustme
  • Computer-Aided Design (CAD), laser scanning and 3D printing “ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) “ in the part design process ensures speed-to-market and a precise fit guaranteed.
  • Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
  • Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
  • 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
  • 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
See More

Delphi – Knock Sensor (Part No.AS10094)

Knock Sensor

from

$47.99
Manufactured to meet or exceed OE requirements; Delphi Knock Sensors help maximize engine performance with all fuels; Delphi Knock Sensors prevent against engine damage from pre-ignition knocking.

Product Features:
  • Delphi knock sensors help maximize engine performance with all fuels
  • Delphi knock sensors prevent against engine damage from pre-ignition knocking
  • Calibrated for a wide variety of frequencies to detect shifts, and adjust to provide accurate signals to help maximize engine performance
  • Flat frequency response allows the same sensor to be used on different engines and the sensor responds to knock frequencies higher than the primary frequency
  • Ground-isolated design with two-wire shielded harness helps protect the sensor signal from electro-magnetic interference (EMI)
  • Self-generating piezoelectric design requires no power to the sensor
See More

DENSO – Coil On Plug Boots-6 (Part No.671-6268)

Coil On Plug Boots-6

from

$58.99
DENSO First Time Fit COP boot sets are identical in form fit color and performance to the factory-installed boots. Every part of each COP boot set construction meets or exceeds OE/OES standards.

Product Features:
  • OE design ensures a tight boot seal that protects against moisture intrusion
  • High temperature resistant material provides greater protection against thermal overload
  • Stainless steel internal spring with resistor to suppress RFI and deliver maximum voltage to the plug
  • Engineered to the specifications used by the original vehicle manufacturer for an exact fit
See More

Carquest – Ignition Switch (Part No.CS804)

Ignition Switch

from

$70.99
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:
  • Designed to OE standards for ease of installation
  • Copper alloy conductors ensure superior electrical conductivity with low resistive losses
  • Our parts are 100% tested to verify both mechanical and electrical switching performance
  • Robust design and high grade materials meet the stringent demands of today’s service professional
  • BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product
See More

Motorcraft – Original Equipment (O.E.) Switch Assembly – Ignition (Part No.SW-6958)

Original Equipment (O.E.) Switch Assembly - Ignition

from

$83.99
The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles.

Product Features:
  • Direct-fit, OE replacement parts – identical to factory installed parts. Robust design helps provide long operating life and excellent performance.
  • All OE switch functions are maintained. Factory connectors help ensure a solid, positive connection. Provided factory mounting points ensure easy installation – new gaskets and attaching hardware is included, where applicable.
See More

Motorcraft – Ignition Switch (Part No.M5050485141MTR)

Ignition Switch

from

$82.48
Ignition Switch

Carquest Premium – Ignition Coil Connector (Part No.PTA3099)

Ignition Coil Connector

from

$87.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Carquest Premium – Ignition Coil Connector (Part No.PTA3032)

Ignition Coil Connector

from

$54.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Carquest – Air Charge Temperature Sensor Connector (Part No.PT5749)

Air Charge Temperature Sensor Connector

from

$27.49
BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:
  • Our ignition coils use 100% pure copper windings in the primary and secondary bobbins to improve durability and provide higher resistance to internal shorts and dielectric breakdown
  • Our premium ignition coils consist of a special blended formula for the best performance, longest life and better heat dissipation
  • A full E-Lam core of silicon steel and solid brass high voltage terminals protects against corrosion. Our ignition coils are built for maximum output voltage
  • Primary and Secondary windings feature enamel magnet wire for the highest temperature rating in the aftermarket
  • BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product
See More

Carquest Premium – Ignition Coil Connector (Part No.PTA1902)

Ignition Coil Connector

from

$13.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:
  • Premium quality materials for longer service life
  • Sealed connections (where applicable) to prevent environmental corrosion and performance issues
  • Global coverage for import and/or domestic applications
  • OE specified wire gauge to ensure a reliable electrical connection
  • Designed to meet or exceed OE specifications in form, fit and function
See More

NGK – OE Series Laser Iridium Spark Plug: Fine Wire Tip Design, ILTR5K13 (Part No.90607)

OE Series Laser Iridium Spark Plug: Fine Wire Tip Design, ILTR5K13

from

$18.99
NGK Laser Iridium spark plugs offer the best combination of performance and longevity. Engineered specifically for OE applications, Laser Iridium spark plugs are tested to the highest standards to ensure quality and durability. Iridium tipped center electrode provides durability six times harder than platinum. NGKs high grade pure alumina ceramic and 98 percent pure copper core prevents the spark plug from overheating while providing reliable starts. Most Laser Iridium spark plugs feature a platinum pad on the ground electrode for even wear in distributorless ignition systems.

Product Features:
  • ACTUAL OE or EQUIVALENT DESIGN: OEM quality construction fine wire iridium alloy center electrode provides consistent performance
  • IRIDIUM ALLOY CENTER ELECTRODE: Iridium’s density (6x that of platinum) and extremely high melting point is perfect for modern high efficiency engines
  • PLATINUM TIP GROUND ELECTRODE: Unless OE specified, platinum protection at the ground electrode provides excellent ignitability and service life
  • SOLID COPPER CORE: 98% pure copper core offers superior heat dissipation, conductivity and ultra wide heat ranges
  • TRIVALENT METAL PLATING: Delivers superior anti-corrosion and anti-seizing properties, ensuring ease of installation and removal
  • RECOMMENDED USAGE: Best for vehicles with OE fine wire iridium alloy plugs
  • Superior Durability: The iridium-tipped center electrode is six times harder than platinum, ensuring long-lasting performance.
  • High-Quality Materials: Constructed with high-grade pure alumina ceramic and a 98 percent pure copper core to prevent overheating and ensure reliable starts.
  • OE Application Specific: Engineered specifically for Original Equipment (OE) applications, ensuring a perfect fit and optimal performance.
  • Even Wear: Features a platinum pad on the ground electrode for even wear, particularly beneficial for distributorless ignition systems.
See More

Motorcraft – Spark Plug (AGSF32WM) (Part No.SP-433)

Spark Plug (AGSF32WM)

from

$6.29
Motorcraft Spark Plugs are original equipment on Ford Motor Company vehicles engineered to meet strict Ford engineering standards to provide original equipment performance and reliability. Delivering performance, reliability and confidence, Motorcraft spark plugs are available for a broad range of applications, including domestic and import cars and trucks of all makes and sizes.

Product Features:
  • Motorcraft spark plugs are matched to specific engines to provide enhanced durability, eliminate misfires, reduce fuel consumption and optimize emissions.
  • Backed by Motorcraft’s Service Parts Warranty
  • Exact fit for Ford, Lincoln and Mercury vehicles
  • Resistant to oxidation and arc erosion.
  • Multi-rib insulator protects against misfire.
  • Service intervals of up to 100,000 miles.
  • Motorcraft Spark Plugs are designed with high quality materials to provide reliable performance for almost any application.
  • Motorcraft Spark Plugs are what was in the vehicle when it was manufactured
  • Motorcraft ignition components help prevent false check engine lights.
See More

NGK – OE Series Laser Platinum Spark Plug: Fine Wire Tip Design, PTR5A-13 (Part No.2467)

OE Series Laser Platinum Spark Plug: Fine Wire Tip Design, PTR5A-13

from

$12.99
NGK Laser Platinum spark plugs provide high ignitability and longer service life compared to conventional nickel spark plugs. Laser Platinum plugs are tested to the highest standards to ensure quality and durability. Engineered specifically for OE applica

Product Features:
  • ACTUAL OE or EQUIVALENT DESIGN: OEM quality construction fine wire platinum alloy center electrode provides consistent performance
  • PLATINUM ALLOY CENTER ELECTRODE: Longer wearing and higher temperature resistance compared to traditional nickel spark plugs
  • PLATINUM TIP GROUND ELECTRODE: Unless OE specified, platinum protection at the ground electrode provides excellent ignitability and service life
  • SOLID COPPER CORE: 98% pure copper core offers superior heat dissipation, conductivity and ultra wide heat ranges
  • TRIVALENT METAL PLATING: Delivers superior anti-corrosion and anti-seizing properties, ensuring ease of installation and removal
  • RECOMMENDED USAGE: Best for vehicles with OE fine wire platinum alloy plugs
See More

DENSO – Iridium Power Spark Plug: Maximum Spark Energy, 0.4mm Iridium Tip, IT16 (Part No.5325)

Iridium Power Spark Plug: Maximum Spark Energy, 0.4mm Iridium Tip, IT16

from

$11.79
Increased performance with World’s smallest Iridium Center Eletrode (0.4mm).

Product Features:
  • World’s smallest Iridium Center Electrode (0.4mm) for improved spark for maximum combustion
  • Patented 360-degree laser welding assembly process
  • U-groove and taper cut ground electrode to maximize flame propagation.
  • Withstands temperatures greater than 4000° Fahrenheit
  • Burnished nickel plating for high temperature endurance and superior corrosion resistance
  • Wide range of part numbers for thousands of applications, including classic and collector cars
  • Iridium Power
See More

2007 Ford Escape Ignition and Tune-Up Products

You count on your 2007 Ford Escape to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Ignition and Tune-Up Products. With 68 Ignition and Tune-Up Products ranging in price from $2.99 to $251.99, you’re sure to find everything you need for your 2007 Ford Escape.

Brands matter. If you want to shop a specific Ignition and Tune-Up Products brand, we stock 13 different brands like Autolite, NGK, and E3. 2007 Ford Escape Ignition and Tune-Up Products start as low as $2.99!

One of the best ways to find top quality OEM or aftermarket Ignition and Tune-Up Products is by asking professionals. Short of that, you can shop with confidence thanks to our 5,009 extensive product reviews on 2007 Ford Escape Ignition and Tune-Up Products. Some of the top-rated Ignition and Tune-Up Products products we carry are Iridium IX Spark Plug: Single Iridium Fine Wire, TR55IX with 4.8 stars and DiamondFIRE Automotive Spark Plug: More Power, Saves Gas with 4.0 stars.

Did we mention you can order your Ignition and Tune-Up Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Ignition and Tune-Up Products inventory for your 2007 Ford Escape below to get started!

Top-Rated Ignition and Tune-Up Products Brands For Your 2007 Ford Escape

Trusted Ignition and Tune-Up Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2007 Ford Escape running right for years to come. In our inventory you’ll find brands like Autolite, NGK, E3, and even more.

Popular Driveworks Ignition and Tune-Up Products

You’ll find popular Driveworks brand products across Ignition Coils and Boots. All are waiting to get your 2007 Ford Escape back on the road. Some of the top-rated Driveworks products in these categories are:
Coil on Plug Coil
from $62.05
(2)
Coil on Plug Coil
Ignition Coils
Coil on Plug Coil
from $81.05
(33)
Coil on Plug Coil
Ignition Coils

Top-Rated Autolite Ignition and Tune-Up Products


If Autolite are what you’re looking for, our inventory holds plenty. We stock Autolite brand Ignition and Tune-Up Products for your 2007 Ford Escape, and some of our most reviewed Autolite parts include:

FAQs for 2007 Ford Escape Ignition and Tune-Up Products

What are the most purchased Ignition and Tune-Up Products for the 2007 Ford Escape?

Out of 68 Ignition and Tune-Up Products for the 2007 Ford Escape, the most popular in our inventory are:
Iridium XP Finewire Spark Plug: Improved Durability, More Focused Ignition
from $9.99
This product is not rated
Iridium XP Finewire Spark Plug: Improved Durability, More Focused Ignition
Spark Plugs

What are the top-rated 2007 Ford Escape Ignition and Tune-Up Products?

Top-rated Ignition and Tune-Up Products for your 2007 Ford Escape based on customer reviews/ratings are:
Iridium IX Spark Plug: Single Iridium Fine Wire, TR55IX
from $11.99
(103)
Iridium IX Spark Plug: Single Iridium Fine Wire, TR55IX
“2000 GT Mustang had bad misfire These plugs made the car run like new again.OE plugs just would not last.”
PT16TT Platinum TT Spark Plug
from $5.99
(90)
PT16TT Platinum TT Spark Plug
“On line”