2007 Chrysler Pacifica Belts and Hoses
More 2007 Chrysler Pacifica Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2007 Chrysler Pacifica, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2007 Chrysler Pacifica Belts and Hoses
Dayco – Serpentine Idler/Tensioner Pulley; Direct Fit, 70 mm Diameter, 24.9 mm Smooth (Part No.89144)
from
$29.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 9 Inch Length (Part No.87624)
from
$16.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 6" Long, .59" Diameter (Part No.A71685)
from
$19.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Poly Rib Serpentine Belt (Part No.W100028021DAY)
from
$42.41
Built for passenger cars and light-duty trucks, Dayco’s extensive line of Poly Rib serpentine belts are engineered for high mileage, demanding drives found in today’s vehicles. As the manufacturer of the first original equipment multi-ribbed serpentine belt, Dayco’s commitment to automotive product excellence and innovation is unwavering. The Dayco Poly Rib W Profile serpentine belt is the most innovative advancement in serpentine belt design in more than 30 years. Developed through extensive laboratory and actual road mileage testing, this unique rib profile EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and help eliminate noisy belt conditions. Constructed with aramid-reinforced EPDM compounds, the Dayco W Poly Rib serpentine belt delivers more than just OE-required quality. It delivers the solution to troublesome drive problems.
Product Features:
See More
Product Features:
- Constructed with aramid-reinforced EPDM compounds
- Engineered to conform to high mileage, worn or misaligned drives
- Helps eliminate noisy belt conditions Related Documents: (PDF 63.78 KB)
Bando – Drive Belt (Part No.W10002489778BAN)
from
$41.31
Drive Belt
Gates – Premium Molded Coolant Hose (Part No.23811)
from
$44.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Flex Radiator Hoses; EPDM Rubber, 15.5 In. Long, 1.5 In. to 1.25 In. Inner Dia. (Part No.81081)
from
$17.49
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.31" Diameter (Part No.E72215)
from
$35.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.22851)
from
$39.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.23810)
from
$46.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17.5" Long, 1.31" Diameter (Part No.E72665)
from
$28.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Serpentine Idler/Tensioner Pulley; Polymer, 65.4mm Dia., 26.6mm Width, 6 Grooves (Part No.89070)
from
$50.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear & tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today.
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 75 mm Diameter (Part No.900162A)
from
$24.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in Italy to the O.E. specified design and meets all performance and durability requirements. Heavy duty Steel V-belt pulley. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the largest original equipment part suppliers to ensure proper form, fit, and performance
- Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
- Installation instructions included.
Dayco – Dayco, Acc. Belt Tension Pulley (Part No.G60111330434DAY)
from
$12.51
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision bearing
- OE High quality pulley assembly
- Durable long life performance.
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999560A)
from
$107.99
This accessory drive tensioner is designed and engineered by Litens – the world’s largest supplier of original equipment (O.E.) belt tensioners in the world. This part was designed for the 2014 to current Jeep Cherokee with 3.2L (Pentastar Engine). The Litens replacement part meets all form, fit, and performance characteristics of the original equipment part (with the exception of not having the car manufacturer’s logo or part number applied to the part). This part is manufactured to meet or exceed the performance and life specifications of the O.E. part. The part features a premium chrome-silicon steel spring, internal damping, a lift-lug feature for ease of installation, a 6203 ball bearing and a plastic pulley molded to exacting specifications. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Designed and engineered by the world’s largest Original Equipment supplier of accessory drive tensioners and pulleys.
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- A plastic pulley specifically molded with tight radial run out for reduced noise and longer life
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt. Belt removal is required to change the tensioner. Therefore, d
- Installation instructions included
Dayco – Serpentine Belt Tensioner: 1 Piece, HD, Built To Outperform And Outlast OE Parts (Part No.89377)
from
$49.99
The Dayco automatic belt tensioner features Dayco’s original, patented flat spring design to provide less operating range variation. It reduces the risk of premature accessory bearing failure due to high tension and lessens the risk of belt noise and slip
Product Features:
See More
Product Features:
- Endures the toughest conditions while promoting quieter performance and longer life
- Features a steel pivot tube on specific designs for enhanced stability
- Built to outperform and outlast competitive OE parts
- This tensioner is another Dayco product proudly made in the USA
Dorman – Automatic Belt Tensioner (Tensioner Only) (Part No.419-006)
from
$75.99
This accessory drive belt tensioner assembly is designed to match the fit of an original equipment assembly on specified vehicles. It is engineered to help ensure proper belt tension when an original belt is slipping, broken, or worn from fatigue.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt tensioner assembly is designed to match the fit of an original equipment assembly on specified vehicles
- Ideal solution – engineered to help ensure proper belt tension when an original belt is slipping, broken, or worn from fatigue
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.31" Diameter (Part No.C72216)
from
$28.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.22852)
from
$41.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 70 mm Diameter (Part No.900125A)
from
$29.99
Litens Automotive is the original equipment (O.E.) supplier for this application. This genuine Litens replacement pulley is also manufactured by Litens, the world’s largest supplier of original equipment power transmission products. Heavy duty thermoplastic pulley construction ensures long life and trouble-free performance. This pulley meets or exceeds all original equipment fit, form, and performance characteristics. For maximum performance and durability, always use genuine Litens components. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Heavy duty thermoplastic pulley construction.
- OE-spec sealed ball bearings with synthetic grease and double lip seals for long life
- Installation instructions included
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit Thermoplastic 63.5 mm Diameter (Part No.900149A)
from
$55.99
This Litens pulley is manufactured by the original equipment pulley supplier to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in Germany to the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction. This is a 63.5mm O.D. grooved pulley. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the original equipment part supplier to ensure proper form, fit and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- Installation instructions included.
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 70 mm Diameter (Part No.900347A)
from
$21.99
This pulley is manufactured by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, specifications and meets performance and durability requirements. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by the world’s largest Original Equipment supplier of accessory drive tensioners and pulleys
- Heavy Duty Polymer Pulley
- Complete assembly including new bolt, dust shield, and spacer.
- Glass Reinforced thermoplastic for optimized dimensional control and running surface durability.
- Precise dimensional tolerance for smooth operation and long life
- Service free sealed ball bearing. Molded-in ball bearing for optimal fit and long life
Driveworks – Poly Rib Belt Serpentine Belt; 50 Long, 5 Rib Count (Part No.500K5)
from
$13.99
This Driveworks v-belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks v-belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
- Meets OEM requirements
Dayco – Poly Rib Belt Serpentine Belt; 79.21 Long, 6 Rib Count (Part No.5060792)
from
$43.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
- Made in the USA
Driveworks – Poly Rib Belt Serpentine Belt; 93.5 Long, 6 Rib Count (Part No.935K6)
from
$27.49
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Dayco – Poly Rib Belt Serpentine Belt; 93.5 Long, 6 Rib Count (Part No.5060935)
from
$45.49
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Popular 2007 Chrysler Pacifica Belts and Hoses Categories
2007 Chrysler Pacifica Belts and Hoses
You count on your 2007 Chrysler Pacifica to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 37 Belts and Hoses ranging in price from $12.51 to $102.99, you’re sure to find everything you need for your 2007 Chrysler Pacifica.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 8 different brands like Dayco, Litens, and Driveworks. 2007 Chrysler Pacifica Belts and Hoses start as low as $12.51!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 1,404 extensive product reviews on 2007 Chrysler Pacifica Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Poly Rib Belt Serpentine Belt; 69.5 Long, 6 Rib Count with 4.5 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.31" Diameter with 4.2 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2007 Chrysler Pacifica below to get started!
Top-Rated Belts and Hoses Brands For Your 2007 Chrysler Pacifica
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2007 Chrysler Pacifica running right for years to come. In our inventory you’ll find brands like Dayco, Litens, Driveworks, and even more.
Popular Dorman Belts and Hoses
You’ll find popular Dorman brand products across Belt Tensioners. All are waiting to get your 2007 Chrysler Pacifica back on the road. Some of the top-rated Dorman products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2007 Chrysler Pacifica, and some of our most reviewed Dayco parts include:
from
$29.99
(251)
Serpentine Idler/Tensioner Pulley; Direct Fit, 70 mm Diameter, 24.9 mm Smooth
Drive Belt Idler Assemblies
from
$51.99
(63)
Serpentine Idler/Tensioner Pulley; Steel, 76mm Dia., 28mm Width, Smooth
Belt Tensioner Pulleys
from
$24.99
(52)
Serpentine Idler/Tensioner Pulley; Polymer, 70mm Dia., 24.5mm Width, Smooth
Idler Pulleys
FAQs for 2007 Chrysler Pacifica Belts and Hoses
What are the most purchased Belts and Hoses for the 2007 Chrysler Pacifica?
Out of 37 Belts and Hoses for the 2007 Chrysler Pacifica, the most popular in our inventory are:
from
$29.99
(7)
O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 70 mm Diameter
Idler Pulleys
What are the top-rated 2007 Chrysler Pacifica Belts and Hoses?
Top-rated Belts and Hoses for your 2007 Chrysler Pacifica based on customer reviews/ratings are:
from
$49.49
(23)
Poly Rib Belt Serpentine Belt; 69.5 Long, 6 Rib Count
“Time will tell. The Drive-Rite serpentine belt appears to be well made, and it fit my Chevy Lumina perfectly. We’ll see how its formulation performs a”
from
$35.99
(5)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16" Long, 1.31" Diameter
“Replacement for upper radiator hose for 2005 Chrysler Pacifica.”
