from

$192.99

This replacement engine coolant thermostat housing assembly is engineered to match the fit and durability of the stock housing assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

Ideal replacement – this engine coolant thermostat housing assembly directly replaces the original water outlet on specified vehicle years, makes and models
Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housing assemblies

from

$6.23

Radiator Drain Plug

from

$117.39

Restore your vehicle’s cooling system to proper working order, and minimize the risk of premature failure, by installing a Bosch Auxiliary Water Pump. Bosch Auxiliary Water Pumps are designed to operate in the highly-stressful environment of today’s cooling systems. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

OE Quality, reliability and service life
Leak-proof sealing of the drive
Fuel savings and reduced emissions
Cooling even without operation of the engine
CO²-reduction by optimized efficiency, speed control and reduced weight
Coverage of a wide hydraulic performance range
Reduced noise level

from

$19.99

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
Brass sensor housing precision machined to meet or exceed OE thermal conductivity
OE precision matched thermistor position for correct output parameters
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$15.69

Radiator Mount

from

$11.49

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$19.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute

from

$6.99

Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings. Permatex Water Pump & Thermostat has the highest water-glycol resistance available in an RTV silicone.

Product Features:

Sensor-safe, noncorrosive RTV silicone gasket material
Formulated specifically for water pumps and thermostat housings
Highest water-glycol resistance available in RTV silicone
Superior adhesion and flexibility
Can be used as a gasket maker or dressing

from

$123.37

Intelligent control systems from MAHLE are used in millions of applications worldwide to provide needs-based precision temperature control. Simple, effective, and tried and tested millions of times over: thermostat inserts from MAHLE provide meticulous regulation of coolant circuits around the world up to approximately 20 m3/h, and ensure ideal operating temperatures in light vehicles, trucks, stationary engines, and also agricultural and construction machinery. Wax elements are at the heart of all MAHLE thermostats and thermostat inserts. These maintenance-free, durable elements have proved their worth in millions of applications. MAHLE, Manufactures a wide range of variants with actuating forces of between 30 N and 2,500 N, small or large displacements, and for a large number of regulation ranges within a temperature span of -20C to +130C.

Product Features:

OE quality and design
Maintenance-free, durable elements

from

$186.78

The Graf Water Pump contains no remanufactured parts and is produced using an optimized all metal impeller design to assist in cooling under high RPM, and performance demands. Selection of raw materials, reliability of machinery and production processes, stringent controls throughout the production process, from melting to fitting, as well as reliability tests performed using equipment able to determine true performance, go to ensure this product is a real guarantee of safety and long life. The Graf water pump is centrifugal in type and comprises a bladed rotor linked by means of a shaft (which rotates on bearings housed in a support) to the drive gear; the seal between the pump and the motor block is guaranteed by a gasket, while the inside of the pump is guaranteed by a mechanical seal. Component parts: Impeller: supplies the fluid with the necessary energy to cover the entire cooling circuit. Mechanical seal: ensures fluid seal inside the pump. Bearing: transmits movement to the impeller and supports any ventilation parts. Entrainment part: for transmitting movement to the bearing. Pump body: supports the basic pump component parts and conveys the coolant in the motor block.

Product Features:

All the component parts fitted are pre-tested to evaluate durability, performance and reliability.
The bearings undergo a durability test equivalent to nominal lifespan and are then inspected to assess integrity.
The mechanical seals are tested in extreme coolant temperature conditions according to predefined cycles.
The shape of the impellers is optimized thanks to the use of prototypes on which flow and performance tests are performed.
On both the entrainment parts and the bodies, the choice of materials and/or technologies different to original ones is made on the basis of structural and mechanical tests.
After assembly all the pumps undergo seal tests on units that reject those with leaks above set limits.

from

$141.47

The Graf Water Pump contains no remanufactured parts and is produced using an optimized all metal impeller design to assist in cooling under high RPM, and performance demands. Selection of raw materials, reliability of machinery and production processes, stringent controls throughout the production process, from melting to fitting, as well as reliability tests performed using equipment able to determine true performance, go to ensure this product is a real guarantee of safety and long life. The Graf water pump is centrifugal in type and comprises a bladed rotor linked by means of a shaft (which rotates on bearings housed in a support) to the drive gear; the seal between the pump and the motor block is guaranteed by a gasket, while the inside of the pump is guaranteed by a mechanical seal. Component parts: Impeller: supplies the fluid with the necessary energy to cover the entire cooling circuit. Mechanical seal: ensures fluid seal inside the pump. Bearing: transmits movement to the impeller and supports any ventilation parts. Entrainment part: for transmitting movement to the bearing. Pump body: supports the basic pump component parts and conveys the coolant in the motor block.

Product Features:

All the component parts fitted are pre-tested to evaluate durability, performance and reliability.
The bearings undergo a durability test equivalent to nominal lifespan and are then inspected to assess integrity.
The mechanical seals are tested in extreme coolant temperature conditions according to predefined cycles.
The shape of the impellers is optimized thanks to the use of prototypes on which flow and performance tests are performed.
On both the entrainment parts and the bodies, the choice of materials and/or technologies different to original ones is made on the basis of structural and mechanical tests.
After assembly all the pumps undergo seal tests on units that reject those with leaks above set limits.

from

$9.12

Water Pump Gasket

from

$9.02

Water Pump Gasket

from

$357.06

Plastic Tank / Aluminum Core Radiator The Nissens Radiator flat tube and double folded fin design offers a significantly better cooling capacity and provides a stronger exterior resisting impacts from stones. This advanced design helps to prevent damage which would negatively affect the cooling capacity and engine performance.

Product Features:

OE-Equivalent.
Direct fit for easy installation.
OE Style mounting brackets and hose connections.
Integrated transmission oil cooler when applicable.
Compact and lightweight.

from

$262.99

New Platinum Pro Radiator, 3.5 And 5.0 Liter Engines

Product Features:

3.5 And 5.0 Liter Engines
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$18.99

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

from

$5.70

The Elring Engine Coolant Thermostat Gasket is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Seals the thermostat and helps prevent coolant from leaking from the engine for proper engine temperature
Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$19.79

Manufactured to meet all OEM specifications. Designed to be easy to install and remove. Manufactured from high quality components with proper relief and vacuum valves. Quality tested to stand up to even the most demanding automotive cooling systems.

Product Features:

Maintains proper cooling system pressure
Easy installation and removal
100% tested to ensure proper pressure and longevity
Meets all OEM specifications

from

$963.88

Auxiliary Fan Assemb

from

$2.84

The Mahle Engine Coolant Thermostat O-Ring is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Seals the thermostat housing and helps prevent coolant from leaking from the engine for proper engine temperature
Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$3.99

MAHLE gaskets provide world class sealing products trusted by OEMs & Technicians around the globe.

Product Features:

All MAHLE gaskets meet or exceed the original equipment specifications providing the finest sealing products available
MAHLE gaskets utilizes OE equivalent or better materials in all our gaskets
MAHLE gaskets is the leader in Domestic, Asian and European applications
The contents of MAHLE gaskets are packaged in shrink wrapped tray, giving you the added security of knowing that you have the right parts, prior to opening the package