from

$177.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1998 and up GM 7.2″ IFS
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$92.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CADI 02-06; CHEV 97-12; DODGE 03-06; FORD 11-15; GMC 96-12; NISSAN 04-22;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1996-2022
Weight approx: 2 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
WITHOUT PLATE
WITHOUT STUDS
EXTENDED DUST SHIELD

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$544.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$251.99

Differential Carrier

from

$48.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.99

Standard open side gear thrust washer for 8.5″ GM.

Product Features:

Side gear thrust washer
Fits GM 8.5″

from

$32.99

Adjuster lock bolt for left hand case half of 7.2″ and 9.25″ GM IFS.

Product Features:

Side adjuster lock bolt
Fits GM 7.2″ IFS and 9.25″ IFS

from

$98.99

Product Features:

MINI SPOOL GM 10 BOLT 8 1/2″ 28 SPLINE

from

$11.58

Differential Drain P

from

$10.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$47.99

Product Features:

Brand may vary by location

from

$15.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$233.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$156.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$51.99

ACDelco GM Original Equipment Pigtail Connectors are connectors ready to be spliced into vehicle harnesses, and are GM-recommended replacements for your vehicle’s original components. These original equipment pigtail connectors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

Protective outer coverings help provide long-lasting durability
Color-coded wires allow for easy installation
GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$649.99

Ring and Pinion Kit

from

$34.99

Building upon a foundation of premium full-line products established under NGK ignition and NTK oxygen sensor products, NTK’s expansion to technical sensors is part of our ongoing commitment to streamline product types and increase coverage under one premium brand: NTK, The Sensor Specialist. With over 80 years of automotive expertise, NGK’s family of automotive products are driven by extreme dedication to innovation, performance and quality. NTK is the only OE supplier with a full-line of technical sensors in the aftermarket for import and domestic vehicles. Drawing from OE experience, NTK sensors undergo extreme testing conditions that include thermal shock, vibration and OBD verification. NTK sensors are manufactured to ensure a quality that meets or exceeds OE specifications. As new vehicles incorporate connected and automated technologies, trust The Sensor Specialist for full-line market support and OE application technology.

Product Features:

NTK ABS Wheel Speed Sensor connectors, mounts and wire lengths are an exact match to OE for worry free installation. Grease, mounting nut and instruction sheet included where applicable.
NTK’s Wheel Speed Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function. Manufactured with weather pack connectors to prevent dirt and moisture contamination.
The ABS ECU monitors the Wheel Speed Sensors rotational speed for anti-lock brake function, stability control and traction control. The ABS sensors report the speed of all four wheels to the ECU to determine if the wheels are locking up.

from

$10.49

Product Features:

Brand may vary by location

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$319.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 2009 and up GM 8.6″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$106.99

This transfer case adapter replaces a damaged or cracked original equipment adapter, restoring a solid connection between the transmission and transfer case. Made of durable aluminum, this adapter includes a new gasket for a complete repair.

Product Features:

Ideal replacement – this transfer case adapter is a direct replacement for a damaged or cracked original equipment adapter
Durable construction – manufactured from aluminum, this transfer case adapter is made to provide years of reliable service
Complete solution – this adapter includes a new transfer case adapter gasket for a complete repair
Quality tested – this part has undergone try-on, corrosion and material testing to ensure a quality fit and long service life

from

$110.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$6.49

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$14.49

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:

Steel-backed Babbitt lining material
Used in automotive and high-performance
Babbitt is designed to perform under extreme loads w/o damaging other engine parts
Babbitt is more environmentally friendly than other material
ISO & QS certified manufacturing

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features: