2006 Freightliner FLD120SD Belts and Hoses
More 2006 Freightliner FLD120SD Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2006 Freightliner FLD120SD, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2006 Freightliner FLD120SD Belts and Hoses
Gates – Premium Molded Coolant Hose (Part No.21042)
from
$42.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Molded Coolant Hose (Part No.24047)
from
$29.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Heat and ozone resistant cover.
- Engineered to resist electrochemical degradation – the leading cause of hose failure.
- Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
- Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
- Temperature Rating: -40° F to 275° F (-40° C to 135° C) in coolant hose applications.
- Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.
Gates – Green Stripe« Heavy-Duty Straight Heater Hose (Part No.28442)
from
$6.49
Heavy-duty construction assures dependable operation in truck, bus and off-road equipment heater systems. For a maintenance free connection, install with Power-Grip SB clamps. Approved for marine applications.
Product Features:
See More
Product Features:
- Green Stripe construction provides best cost-per-mile economics
- Abrasion-resistant cover
- Engineered with materials to resist electrochemical degradation
- Reduces water loss from water permeating the hose wall and cover
- Exceeds SAE 20R1 Type EC (Class D-1 tube and cover Standard Wall)
- Temperature Range: -40 Deg. F to +275 Deg. F (-40 Deg. C to +135 Deg. C)
- Note: For a maintenance free connection, use PowerGrip SB clamps
- Caution: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.75" Inside Diameter (Sold by foot) (Part No.28412)
from
$3.99
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.38076)
from
$74.99
Product Features:
See More
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 75 mm Diameter (Part No.900042A)
from
$50.99
This pulley is supplied by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part meets all performance and durability requirements. Fits Heavy Duty truck applications including Freightliner, Volvo, Gillig, New Flyer, Sterling, and Western Star. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Gates – DRIVEALIGN PULLEY (Part No.36164)
from
$109.99
DRIVEALIGN PULLEY
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.910033A)
from
$232.99
This Litens supplied tensioner is manufactured to original equipment specifications. Heavy duty steel pulley construction ensures long life and trouble-free performance. This tensioner meets or exceeds all original equipment fit, form, and performance characteristics. For maximum performance and durability, always use genuine Litens components. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Designed and engineered by the world’s largest Original Equipment supplier of accessory drive tensioners and pulleys
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- Installation instructions included.
- Heavy Duty Electro-deposited coated (e-coat) Steel Pulley for superior corrosion resistance.
- Professional Mechanics will change this tensioner in approx. 1/2 hour
- Due to the fact that belts and tensioners have similar Original Equipment “design life targets”, it is often a best practice to replace the belt tensioner when replacing a worn or broken belt. Belt removal is required to change the tensioner. Therefore, d
Gates – FleetRunner½ Heavy-Duty Automatic Belt Drive Tensioner (Part No.38503)
from
$171.99
Product Features:
See More
- Optimized components engineered for maximum strength and durability
- Patented design provides superior belt alignment and tension for improved drive efficiency and life
- Patented labyrinth seal prevents contamination of internal parts for maximum durability and service life
- Long-lasting steel pulleys with dust shields to protect internal bearings from contamination
- Double row bearings carry more load and last up to 3X longer than two individual bearings
- Chrome-silicone round torsion spring for less +ex-fatigue than +at-spring designs
- Patented damping mechanism provides maximum stability, reducing vibration and increasing the life of the belt, tensioner and other accessory drive components
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.910580A)
from
$151.99
This Heavy duty belt tensioner is manufactured by one of the largest original equipment tensioner suppliers to ensure proper fit and performance. This tensioner is produced for serpentine belt routing applications and is made of high strength steel for improved life and durability. As with the original equipment part, this replacement tensioner fits F’liner Columbia/Int’l Paystar 5900i/KW C500,T600,T660,T800,W900/Peterbilt ,367,378,379,386,387,388,389/Sterling L-Line/Western Star 4900FA,4900SA; CAT C15; 05-09 There is a lift feature molded into the arm on this tensioner for ease of belt removal and replacement. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the largest original equipment part suppliers to ensure proper form, fit, and performance.
- Internal “round spring” technology to provide constant belt tension and alignment throughout its service life. The internal damping design provides quiet, smooth, system performance.
- Heavy duty steel pulley with close tolerance ball bearing pocket and electro-deposited coating for superior corrosion resistance
- Flat steel pulley
- Installation instructions included
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 19" Long, 2.50" Diameter (Part No.E70922)
from
$26.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Green Stripe« 2-Ply Straight Coolant Hose (Part No.24236)
from
$3.79
Stick hose designed for demanding heavy-duty coolant/air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Cover marked in 1 in. increments to facilitate approximate cut lengths, allows ┐custom-fit” installations
- Engineered with compounds that resist electrochemical degradation
- Approved for marine applications
- Exceeds SAE 20R1 Type EC (Class D-1 Tube, and cover, Standard Wall)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: For a maintenance free connection, use PowerGrip SB clamps
- Caution: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the inch. See store for details.
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 15.50" Long, 2.50" Diameter (Part No.E70909)
from
$28.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – V-Ribbed (Heavy Duty) Serpentine Belt: 56.5" Long, 6 Rib Count, Exact Fit (Part No.K060559HD)
from
$40.99
Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at prolonged extreme operating temperatures
- Heavy-duty construction resists cracking and wear, even at extreme temperatures
- Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
- Problem solver designed for the toughest applications
- Consistently outperforms other heavy-duty serpentine belts on the market
- Engineered to save your fleet money and reduce downtime
- Tensioner Replacement is Recommended (if equipped)
Gates – V-Ribbed (Heavy Duty) Serpentine Belt: 59.213" Long, 6 Rib Count, Exact Fit (Part No.K060586HD)
from
$39.99
Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at prolonged extreme operating temperatures
- Heavy-duty construction resists cracking and wear, even at extreme temperatures
- Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
- Problem solver designed for the toughest applications
- Consistently outperforms other heavy-duty serpentine belts on the market
- Engineered to save your fleet money and reduce downtime
- Tensioner Replacement is Recommended (if equipped)
Gates – V-Ribbed (Heavy Duty) Serpentine Belt: 58.527" Long, 10 Rib Count, Exact Fit (Part No.K100579HD)
from
$72.99
Gates FleetRunner Micro-V Belts are designed for the toughest applications. FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures, making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at prolonged extreme operating temperatures
- Heavy-duty construction resists cracking and wear, even at extreme temperatures
- Special compound provides unmatched flexibility, stability, load carrying capacity and belt life
- Problem solver designed for the toughest applications
- Consistently outperforms other heavy-duty serpentine belts on the market
- Engineered to save your fleet money and reduce downtime
- Tensioner Replacement is Recommended (if equipped)
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 78 mm Diameter (Part No.900466A)
from
$62.99
This pulley is supplied by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part meets all performance and durability requirements. Fits Heavy Duty truck applications including the Mack LE Series. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by one of the world’s largest Original Equipment suppliers of accessory drive tensioners and pulleys
- Heavy Duty Steel Pulley
- Precision steel stamping with close tolerance ball bearing pocket.
- Electro-deposited coating (e-coat) for superior corrosion resistance.
- Running surface designed and engineered for proper belt tracking.
Dayco – Serpentine Assy. Idler/Tensioner Pulley; Steel, 77mm Dia., 30mm Width, 6 Grooves (Part No.89171)
from
$56.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear & tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today.
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Gates – DriveAlign½ Belt Drive Idler/Tensioner Pulley (Part No.36269)
from
$148.99
Product Features:
See More
- Steel and thermoplastic construction designed to tight manufacturing tolerances for high durability and quality performance
- Built to last with a superior resistance to dirt, salt, chemicals and other under-hood contaminants
- OE-quality fit for virtually every domestic or import vehicle on the road today
- Bearings meet or exceed OE standards with application-specific speed and load requirements, to withstand high under hood temperatures
- Premium bearings eliminate bearing noise
- Mounting hardware included for some popular applications
- Reliable operation under severe conditions
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 75 mm Diameter (Part No.900614A)
from
$171.99
This pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for 2006-2010 Freightliner Classic, Bus Class M2, Cascadia, Century Class, Columbia / Sterling A-Line, L-Line with 4000 Diesel It’s a serpentine belt routing application and conforms to original equipment material, tolerances, and specifications. This replacement part is made to the O.E. specified design and meets all performance and durability requirements. Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance. This pulley comes with a dust shield, installation bolt and retainer. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Dayco No Slack Gold Label – Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 32.8mm Width, Smooth (Part No.89105)
from
$45.99
Designed to replace idler and tensioner pulleys for serpentine drives in heavy-duty diesel engine applications, Dayco HD idler/tensioner pulleys are machined from high-strength steel or powdered metal material to provide excellent wear resistance under ha
Product Features:
See More
Product Features:
- Engineered for the demanding drive systems of today’s class 4-8 heavy-duty commercial trucks
- Premium OE technology to ensure peak performance under extreme conditions
- Utilizes 3D dimensional computer aided design (CAD) and finite element analysis (FEA) for optimal design and maximum structural integrity
- Meets or exceeds OE quality
Dayco No Slack Gold Label – Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 54.5mm Width, 12 Grooves (Part No.89113)
from
$66.99
Designed to replace idler and tensioner pulleys for serpentine drives in heavy-duty diesel engine applications, Dayco HD idler/tensioner pulleys are machined from high-strength steel or powdered metal material to provide excellent wear resistance under ha
Product Features:
See More
Product Features:
- Engineered for the demanding drive systems of today’s class 4-8 heavy-duty commercial trucks
- Premium OE technology to ensure peak performance under extreme conditions
- Utilizes 3D dimensional computer aided design (CAD) and finite element analysis (FEA) for optimal design and maximum structural integrity
- Meets or exceeds OE quality
Dayco No Slack Gold Label – Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 39.25mm Width, Smooth (Part No.89101)
from
$44.99
Designed to replace idler and tensioner pulleys for serpentine drives in heavy-duty diesel engine applications, Dayco HD idler/tensioner pulleys are machined from high-strength steel or powdered metal material to provide excellent wear resistance under ha
Product Features:
See More
Product Features:
- Engineered for the demanding drive systems of today’s class 4-8 heavy-duty commercial trucks
- Premium OE technology to ensure peak performance under extreme conditions
- Utilizes 3D dimensional computer aided design (CAD) and finite element analysis (FEA) for optimal design and maximum structural integrity
- Meets or exceeds OE quality
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5" Long, 2.50" Diameter (Part No.B71812)
from
$21.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Molded 90 Degree Silicone Coolant Hose (Part No.28210)
from
$196.99
Newer heavy-duty engines with advanced emissions systems (from 2007 to current model year) produce higher under-hood temperatures, requiring the use of silicone coolant hose. In these new low engine-air-flow and high-heat conditions, Gates Silicone Coolant Hose is the perfect product.
Product Features:
See More
Product Features:
- Premium 4-ply construction
- High-heat resistance material meets or exceeds OE specifications
- Multiple layers of first grade silicone material
- Industry standard blue cover and orange tube for easy identification
- Polyester knit reinforcement, unaffected by permeation of coolants and heat
- Extra thick and resilient tube prevents cold water leaks and hardening under effect of heat
- High-grade silicone cover resists coolants, ozone, weathering, sunlight and extreme ambient temperatures
- Exceeds requirements of SAE J20R1, Class A
- Temperature Range: -65 Deg. F to +350 Deg. F (-54 Deg. C to +177 Deg. C)
- Gates also offers application-specific molded silicone coolant hose for exact dimensional specifications
Gates – Molded Heater Hose: EPDM, Direct Fit, 2.5" Inside Diameter (Part No.21135)
from
$52.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube; synthetic fiber knit reinforcement; heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.20611)
from
$25.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Straight Radiator Hoses; EPDM Rubber, HD, 2 1/2 Inch Inner Dia. (Sold by inch) (Part No.77250GL)
from
$2.49
Designed for a wide range of heavy-duty truck applications where the routing is relatively straight, the Dayco straight radiator hose – H.D. is made with the highest quality woven mesh fabric reinforcement, neoprene cover and nitrile tube compounds to withstand the most corrosive elements in diesel engines. Providing protection from oil, coolants, coolant additives and heat, it has a temperature rating of -40?F (-40?C) to +212?F (+100?C).
Product Features:
See More
Product Features:
- Capable of withstanding extreme temperatures and high-pressure environments
- Designed to meet SAE requirements J20R1, Class B Tube, Class C Cover, standard wall construction
- Not suitable for fuel or oil transfer
- PLEASE NOTE: Priced and sold by inch. See store for details.
Popular 2006 Freightliner FLD120SD Belts and Hoses Categories
2006 Freightliner FLD120SD Belts and Hoses
You count on your 2006 Freightliner FLD120SD to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 51 Belts and Hoses ranging in price from $3.99 to $264.99, you’re sure to find everything you need for your 2006 Freightliner FLD120SD.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 3 different brands like Dayco, Gates, and Litens. 2006 Freightliner FLD120SD Belts and Hoses start as low as $3.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 50 extensive product reviews on 2006 Freightliner FLD120SD Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are V-Ribbed (Heavy Duty) Serpentine Belt: 58.527" Long, 10 Rib Count, Exact Fit with 5.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2006 Freightliner FLD120SD below to get started!
Top-Rated Belts and Hoses Brands For Your 2006 Freightliner FLD120SD
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2006 Freightliner FLD120SD running right for years to come. In our inventory you’ll find brands like Dayco, Gates, Litens, and even more.
Popular Dayco Belts and Hoses
You’ll find popular Dayco brand products across Serpentine and V Belts. All are waiting to get your 2006 Freightliner FLD120SD back on the road. Some of the top-rated Dayco products in these categories are:
from
$77.99
(47)
Poly Rib Belt HD Serpentine Belt; 85.5 Long, 8 Rib Count, Heavy Duty
Serpentine Belts
FAQs for 2006 Freightliner FLD120SD Belts and Hoses
What are the most purchased Belts and Hoses for the 2006 Freightliner FLD120SD?
Out of 51 Belts and Hoses for the 2006 Freightliner FLD120SD, the most popular in our inventory are:
from
$44.99
This product is not rated
Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 39.25mm Width, Smooth
Drive Belt Idler Assemblies
from
$77.99
This product is not rated
V-Ribbed (Heavy Duty) Serpentine Belt: 83.75" Long, 8 Rib Count, Exact Fit
Serpentine Belts
from
$45.99
This product is not rated
Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 32.8mm Width, Smooth
Drive Belt Idler Assemblies
What are the top-rated 2006 Freightliner FLD120SD Belts and Hoses?
Top-rated Belts and Hoses for your 2006 Freightliner FLD120SD based on customer reviews/ratings are:
from
$72.99
(1)
V-Ribbed (Heavy Duty) Serpentine Belt: 58.527" Long, 10 Rib Count, Exact Fit
“This is the stock pulley size severe duty “green” belt for our Hellcat supercharger.Recommend this belt when servicing the Hellcats…”
