2006 Ford F-450 Super Duty Transmission Parts

Below you will find various in-demand Ford Transmission Parts, components and accessories for your 2006 F-450 Super Duty. Advance Auto Parts has popular F-450 Super Duty parts like Automatic Transmission Parts, Transmission Cooler and Parts, Transmission Mounts and more. You’ll also find aftermarket and OEM Transmission Parts for other F-450 Super Duty model years including 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022 and more. Select a category of 2006 Ford F-450 Super Duty Transmission Parts below and start saving instantly.

Popular 2006 Ford F-450 Super Duty Transmission Parts Categories

Automatic Transmission Shift Tubes

Gear Shift Levers

Automatic Transmission Shift Linkages

Automatic Transmission Oil Temperature Sensors

OE Transmission Coolers

Manual Transmission Differential Bearings

Master and Slave Cylinder Assemblies

Transmission Solenoids

Transmission Oil Cooler Lines

Countershaft Bearings

Transmission Pan Gaskets

Output Shaft Speed Sensor Connectors

Automatic Transmission Drain Plugs

Automatic Transmission Line Connectors

Pinion Bearings

Transmission Mounts

Transmission Oil Pans

Back Up and Neutral Safety Switches

Automatic Transmission Shift Lever Bushings

Transmission Rebuild Kits

Speed Sensors

Automatic Transmission Shift Tube Lever Pins

Transmission Speed Sensors

Transmission Bushings

Transmission Temperature Sensors

Automatic Transmission Oil Pump Seals

Pinion Seals

Transmission Seals and O-rings

Automatic Transmission Oil Cooler Assemblies

Back Up Light Switch Connectors

Manual Transmission Bearing and Seal Overhaul Kits

Extension Housing Seals

Manual Transmission Output Shaft Seals

Automatic Transmission Case Vents

Shaft Seals

Manual Transmission Main Shafts

Gear Shift Lever Bushing

Overdrive Shift Buttons

Input Shaft Bearings

Back Up Lamp Connectors

Manual Transmission Blocking Rings

Shift Forks

Shift Shaft Seals

Remanufactured Automatic Transmissions

Manual Transmission Gears

Manual Transmission Synchro Assemblies

Manual Transmission Input Shafts

Manual Transmission Synchro Sleeves

Essential Transmission Parts for 2006 Ford F-450 Super Duties

from

$51.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Sealed connections (where applicable) to prevent environmental corrosion and performance issues
Global coverage for import and/or domestic applications
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$26.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$161.99

New Platinum Pro Automatic Transmission Oil Cooler Assembly, 5.4 Liter V8 Engine Or 6.8 Liter V10, Up To 02/24/2001 Production Date

Product Features:

5.4 Liter V8 Engine Or 6.8 Liter V10, Up To 02/24/2001 Production Date,
Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$356.99

For modern, foot-operated clutches we offer hydraulic release systems that not only replace cable-actuated systems, they also fit into increasingly narrow engine compartments. Because there is no more friction from the cable, clutch wear is lowered dramatically while driving comfort improves.

from

$9.99

This transmission drain plug is designed to match the dimensions and function of the original plug on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

Direct replacement – this transmission drain plug matches the dimensions and function of the factory hardware on specified vehicle years, makes and models
Ideal solution – this drain plug is a reliable replacement for an original part that is damaged or lost during service
Durable construction – this part is made from quality materials to ensure reliable performance and a long service life
Quality assured – backed by a team of product experts in the United States and more than a century of automotive experience

from

$20.49

When the transmission linkage clips break on many Ford, Lincoln and Mercury vehicles, you usually have to replace the entire shifter cable assembly. This Dorman OE FIX clip allows direct replacement of only the failed original clip, saving money.

Product Features:

Smart fix – this direct replacement shift linkage clip saves time and money by directly replacing the failure-prone clip on many Ford, Lincoln and Mercury vehicles
Effective alternative – allows you to restore shifter mechanism operation without replacing the entire shifter cable assembly
Application specific – made for certain Ford, Lincoln and Mercury vehicles
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$46.99

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$4353.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required. All of friction components are replaced with upgraded heavy duty parts. Drum assemblies are air checked and side play is checked to assure proper clearance. All of seals, o’rings and gaskets are replaced. All of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing. Transmissions are assembled, end plays are set and fasteners are torqued to the required specification. All of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno test. Transmission park locking mechanism is checked during dyno test. (where applicable). (Torque Converter) All of converters are dynamic balanced. All of pumps are furnaced brazed. All new bearings and o’rings. All new springs and rollers in stator. All new thrust washers. All new friction liners in overdrive lockup converters. Converter endplay and hub/pump runout and diameter is checked.

Product Features:

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

from

$71.99

Shifter feeling shiftless lately? This replacement automatic transmission shift lever directly restores operation to catch gears effectively, while retaining original equipment look and feel.

Product Features:

Direct replacement – this shift lever matches the look and function of the original equipment shifter on specific vehicle model years, makes and models
Effective fix – replacement restores proper shifting for safe driving
Matching appearance – specifically designed to provide seamless replacement
Trustworthy quality – backed by team of engineers and inspectors in the United States

from

$29.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$6.99

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$11.49

This automatic transmission overdrive button kit matches the original parts to repair a missing or damaged overdrive button on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this automatic transmission overdrive button kit is designed to match the original components required to repair a missing or damaged overdrive button on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing, damaged or failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.99

Building upon a foundation of premium full-line products established under NGK ignition and oxygen sensor products, NTK’s expansion to technical sensors is part of our ongoing commitment to streamline product types and increase coverage under one premium brand NTK, The Sensor Specialist. With over 80 years of automotive expertise, NGK’s family of automotive products are driven by extreme dedication to innovation, performance and quality. is the only OE supplier with a full line of technical sensors in the aftermarket for import and domestic vehicles. Drawing from OE experience, sensors undergo extreme testing conditions that include thermal shock, vibration and OBD verification. sensors are manufactured to ensure a quality that meets or exceeds OE specifications. As new vehicles incorporate connected and automated technologies, trust The Sensor Specialist for full-line market support and OE application technology.

Product Features:

The Automatic Transmission Fluid Temperature Sensor monitors the temperature of the transmission fluid. The transmission control module (TCM) uses input from this sensor to control transmission operations.
NTK’s Automatic Transmission Fluid Temperature Sensors are manufactured to operational performance standards to meet or exceed OE fit, form and function to ensure proper monitoring of the transmission’s oil temperature.

from

$90.99

AT CONTR SOLENOID

from

$412.99

This automatic transmission control solenoid is designed to match the fit and function of the original solenoid on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this automatic transmission control solenoid is designed to match the fit and function of the original solenoid on specified vehicles
Ideal solution – this solenoid is a reliable replacement for an original part that is damaged or has failed due to fatigue, excessive heat or electrical current
Durable construction – this solenoid is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$85.99

The Imperial Maxi-Cool XL’s plate and fin design offer excellent cooling efficiency in a compact, space-efficient design.

Product Features:

Class “A” motor homes, large travel trailers, 5th-wheel trailers
GVWR up to 30,000 lbs.; towing up to 10,000 lbs.
Compatible with OEM cooler systems
33% more efficient than a comparable tube and fin design

from

$141.99

This automatic transmission oil cooler is designed to match the function of an original cooler on specified vehicles. It is engineered to help maintain proper engine oil temperature when an original cooler has failed from heat, corrosion, or damage.

Product Features:

Direct replacement – this automatic transmission fluid cooler is designed to match the function of an original cooler on specified vehicle
Ideal solution – engineered to help maintain proper transmission fluid temperature when an original cooler has failed from heat, corrosion or damage
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$605.99

aFe Powers new deep transmission pan brings performance engineering to the protection of your trucks transmission. This transmission pan has additional capacity for 7-1/2 more quarts over stock at the factory line, a magnetic drain plug and a 1/8″ NPT port for your temperature sensor. Built-in internal and external fins transfer heat from the fluid to the outside air for maximum cooling. This transmission pan is constructed out of durable die-cast A380 aluminum with reinforced ribs and a raw finish with machined accents for maximum strength and styling.

Product Features:

Internal/External Fins Transfer Heat From Fluid To Ambient Air
Large Neodymium Magnet Drain Plus Captures Loose Particles
1/8 in. NPT Port Comes Ready To Use For Your Temp Sensor
Comes Complete w/All Necessary Hardware To Bolt Directly On

from

$66.99

This replacement transmission oil pan is a direct replacement for a damaged original equipment transmission pan. Made of quality materials, it’s designed for reliable, leak-free service.

Product Features:

Ideal replacement – this transmission oil pan matches the fit and function of the original pan for a trouble-free replacement
Durable construction – this transmission oil pan is made of quality materials for durability and leak-free performance
Cost-effective solution – offers original equipment performance at competitive price
Quality tested – this part has undergone try-on testing to ensure a quality fit

from

$12.99

This automatic transmission shift lever bushing is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this automatic transmission shift lever bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$32.49

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Transmission line fitting kit
Ford; 1/2″-20 inverted flare, deep thread
Helps simplify transmission cooler installation
Allows for auxiliary transmission cooler installation without cutting OE lines
Crafted from high-quality material that makes it durable and longer-lasting
A high quality, direct fit OE replacement
Easily connects the transmission cooler line to the cooler hose
Hose clamps required
Crafted from high-quality material that makes it durable and longer-lasting
A high quality, direct fit OE replacement
Easily connects the transmission cooler line to the cooler hose
Hose clamps required

from

$41.99

Product Features:

Transmission line fitting kit
Ford; 5/8″-18 inverted flare, deep thread
Helps simplify transmission cooler installation
Allows for auxiliary transmission cooler installation without cutting OE lines
Crafted from high-quality material that makes it durable and longer-lasting
A high quality, direct fit OE replacement
Easily connects the transmission cooler line to the cooler hose
Hose clamps required

from

$14.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.05

Qualities that have made SMP an industry leader for more than 95 years, innovation, engineering expertise, superior quality, meticulous testing, unmatched customer service, competitive pricing, and brand integrity, are at the heart of every TechSmart part.

Product Features:

Improved 3.2 mm design at highest stress point prevents fractures, which are the leading cause of failure
Upgraded design extends service life, which saves you from future, labor-intensive repairs
Direct OE replacement ensures fit and function like the original
All TechSmart® parts meet or exceed OE performance, providing today’s technician with the quality parts needed to get the job done right, the first time

from

$6.49

This Automatic Transmission Shift Tube Bushing is a direct replacement for the original unit per vehicle applications.

Product Features:

Application matched component to ensure the system can be returned to like new condition.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$7.99

This automatic transmission shift tube bushing is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this automatic transmission shift tube bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$73.99

Direct replacement – this automatic transmission shift tube bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Upgrade your 2006 Ford F-450 Super Duty with Top-Quality Transmission Parts

When it comes to maintaining or upgrading your 2006 Ford F-450 Super Duty, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Transmission Parts are key to keeping your F-450 Super Duty functioning at its best. At Advance Auto Parts, we offer a wide selection of 111 Transmission Parts for the 2006 Ford F-450 Super Duty, designed to meet your needs without breaking the bank. From Automatic Transmission Part replacements to Transmission Cooler and Parts upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Transmission Parts for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Transmission Parts for your 2006 Ford F-450 Super Duty at great prices. Our Transmission Parts inventory for this model ranges from just $3.99 to $2,924.99, with an average price of $286.96. Our 111 Transmission Parts in stock come from 17 trusted brands, so you’re sure to find the right part for your 2006 Ford F-450 Super Duty without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2006 Ford F-450 Super Duty, we stock popular OEM and aftermarket Transmission Parts from top names like National, Dorman, Imperial, and more. National Transmission Parts start at just $14.99 and boast an impressive 4.3 stars average rating from customers. Dorman and Imperial also bring quality to the table, with Transmission Parts available starting at $6.99, and at an average 4.2 stars rating. With 969 customer reviews and counting, our 2006 Ford F-450 Super Duty Transmission Parts have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Transmission Part upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2006 Ford F-450 Super Duty is always ready to roll. We’re committed to providing you with everything you need to keep your F-450 Super Duty in top shape, all in one place. Start shopping confidently below for your 2006 Ford F-450 Super Duty!

Best-Selling Automatic Transmission Parts for 2006 Ford F-450 Super Duties

Enhance the driving experience in your Ford with 28 quality Automatic Transmission Part components, starting at $5.99.

show more show less

from

$7.99

Direct replacement – this automatic transmission shift tube bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$22.99

This automatic transmission shift tube clamp is designed to match the fit and function of the original clamp on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this automatic transmission shift tube clamp is designed to match the fit and function of the original clamp
Restores functionality – this clamp is made to fit and fully restore part functionality after the original clamp fails
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$6.99

This automatic transmission shift tube lever pin is designed to match the fit and function of the original pin on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this automatic transmission shift tube lever pin is designed to match the fit and function of the original pin on specified vehicles
Restores functionality – this pin is made to fit and fully restore part functionality after the original pin fails
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.05

Improved 3.2 mm design at highest stress point prevents fractures, which are the leading cause of failure
Upgraded design extends service life, which saves you from future, labor-intensive repairs
Direct OE replacement ensures fit and function like the original
All TechSmart® parts meet or exceed OE performance, providing today’s technician with the quality parts needed to get the job done right, the first time

from

$12.99

Direct replacement – this automatic transmission shift lever bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$11.49

Direct replacement – this automatic transmission overdrive button kit is designed to match the original components required to repair a missing or damaged overdrive button on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing, damaged or failed due to wear
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$56.99

This automatic transmission shift tube is designed to match the fit and function of the original tube on specified applications, and is engineered for reliable performance and durability.

Product Features:

Direct replacement – this automatic transmission shift tube is designed to match the fit and function of the original tube on specified applications
Restores functionality – this tube is made to fit and fully restore part functionality after the original tube fails
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$20.49

Smart fix – this direct replacement shift linkage clip saves time and money by directly replacing the failure-prone clip on many Ford, Lincoln and Mercury vehicles
Effective alternative – allows you to restore shifter mechanism operation without replacing the entire shifter cable assembly
Application specific – made for certain Ford, Lincoln and Mercury vehicles
Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience

from

$31.99

Direct replacement – this automatic transmission shift tube is designed to match the fit and function of the original tube on specified applications
Restores functionality – this tube is made to fit and fully restore part functionality after the original tube fails
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$90.99

AT CONTR SOLENOID

from

$95.99

AT CONTR SOLENOID

from

$91.99

AT CONTR SOLENOID

from

$2924.99

At Shift Pro Inc, fully remanufactured transmissions go beyond the name. So, what’s in that name to start? Pro Engineering: your transmission has been re-engineered to meet or exceed OE standards for tolerances, durability, and quality. Pro Performance: upgraded components and a fully remanufactured torque converter add to enhanced durability over your transmission’s lifetime. Pro Performance: hot-, cold-, load-, and simulated road-tested on custom dynamometers, your transmission is ready to go, wherever you’re headed.

Product Features:

Fully tested torque converter included. Shift Pro Inc tests for leaks, lock-up, concentricity, and balance to eliminate the possibilities of front seal leaks, premature bushing wear, and vibration.
All dynamometer testing is conducted with Shift Pro Inc’s custom testing program for at least 30 minutes.
During dynamometer testing, Shift Pro Inc transmissions are cold, hot, load, and road tested using a fully synthetic transmission fluid and filtration system.
All wear-prone valves in the completely remanufactured valve body are restored to stringent specifications and vacuum tested to verify proper function.
Shift Pro Inc’s quality control process includes build specification checks performed by four different specialized technicians during the remanufacturing process.
No paperwork or registration is required with Shift Pro Inc’s warranty. Each no-hassle warranty is attached to the vehicle VIN and transferrable with ownership.
Product might not be available in all states due to local laws.

from

$2924.99

Fully tested torque converter included. Shift Pro Inc tests for leaks, lock-up, concentricity, and balance to eliminate the possibilities of front seal leaks, premature bushing wear, and vibration.
All dynamometer testing is conducted with Shift Pro Inc’s custom testing program for at least 30 minutes.
During dynamometer testing, Shift Pro Inc transmissions are cold, hot, load, and road tested using a fully synthetic transmission fluid and filtration system.
All wear-prone valves in the completely remanufactured valve body are restored to stringent specifications and vacuum tested to verify proper function.
Shift Pro Inc’s quality control process includes build specification checks performed by four different specialized technicians during the remanufacturing process.
No paperwork or registration is required with Shift Pro Inc’s warranty. Each no-hassle warranty is attached to the vehicle VIN and transferrable with ownership.
Product might not be available in all states due to local laws.

from

$2924.99

Fully tested torque converter included. Shift Pro Inc tests for leaks, lock-up, concentricity, and balance to eliminate the possibilities of front seal leaks, premature bushing wear, and vibration.
All dynamometer testing is conducted with Shift Pro Inc’s custom testing program for at least 30 minutes.
During dynamometer testing, Shift Pro Inc transmissions are cold, hot, load, and road tested using a fully synthetic transmission fluid and filtration system.
All wear-prone valves in the completely remanufactured valve body are restored to stringent specifications and vacuum tested to verify proper function.
Shift Pro Inc’s quality control process includes build specification checks performed by four different specialized technicians during the remanufacturing process.
No paperwork or registration is required with Shift Pro Inc’s warranty. Each no-hassle warranty is attached to the vehicle VIN and transferrable with ownership.
Product might not be available in all states due to local laws.

from

$2924.99

Fully tested torque converter included. Shift Pro Inc tests for leaks, lock-up, concentricity, and balance to eliminate the possibilities of front seal leaks, premature bushing wear, and vibration.
All dynamometer testing is conducted with Shift Pro Inc’s custom testing program for at least 30 minutes.
During dynamometer testing, Shift Pro Inc transmissions are cold, hot, load, and road tested using a fully synthetic transmission fluid and filtration system.
All wear-prone valves in the completely remanufactured valve body are restored to stringent specifications and vacuum tested to verify proper function.
Shift Pro Inc’s quality control process includes build specification checks performed by four different specialized technicians during the remanufacturing process.
No paperwork or registration is required with Shift Pro Inc’s warranty. Each no-hassle warranty is attached to the vehicle VIN and transferrable with ownership.
Product might not be available in all states due to local laws.

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required. All of friction components are replaced with upgraded heavy duty parts. Drum assemblies are air checked and side play is checked to assure proper clearance. All of seals, o’rings and gaskets are replaced. All of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing. Transmissions are assembled, end plays are set and fasteners are torqued to the required specification. All of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno test. Transmission park locking mechanism is checked during dyno test. (where applicable). [Torque Converter] All of converters are dynamic balanced All of pumps are furnaced brazed. All new bearings and o’rings. All new springs and rollers in stator. All new thrust washers. All new friction liners in overdrive lockup converters. Converter endplay and hub/pump runout and diameter is checked

Product Features:

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
Product might not be available in all states due to local laws.

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
Product might not be available in all states due to local laws.

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

from

$2569.99

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno

from

$73.99

Direct replacement – this automatic transmission shift tube bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Most Popular 2006 Ford F-450 Super Duty Transmission Cooler and Parts

Customize your Ford with 16 Transmission Cooler and Parts products like Transmission Oil Cooler Lines, OE Transmission Coolers, and Automatic Transmission Oil Cooler Assemblies, all priced under $400.99.

show more show less

from

$85.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Imperial high-performance transmission cooler
Size: 3/4″ x 10″ x 15-7/8″
SAE 45-degree fittings for maximum reliability
Electrostatic powder-coated to prevent corrosion
SAE 45 degree fittings for maximum reliability
Electrostatically powder coated to prevent corrosion
All aluminum lightweight construction
SAE 45 degree fittings for maximum reliability
Electrostatically powder coated to prevent corrosion
All aluminum lightweight construction

from

$73.99

Product Features:

Imperial Maxi-Cool« plate and fin transmission cooler
Size: 3/4″ x 11″ x 7-1/2″
Mid-size and full-size cars, pickups
GVWR up to 20,000 lbs.; towing up to 2,500 lbs.
Compatible with OEM cooler systems
Made with the highest quality materials
100% pressure testing to 150 PSI for quality assurance
33% more efficient than a comparable tube and fin design

from

$400.99

Direct replacement – this automatic transmission fluid cooler is designed to match the function of an original cooler on specified vehicle
Ideal solution – engineered to help maintain proper transmission fluid temperature when an original cooler has failed from heat, corrosion or damage
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$85.99

The Imperial Maxi-Cool XL’s plate and fin design offer excellent cooling efficiency in a compact, space-efficient design.

Product Features:

Class “A” motor homes, large travel trailers, 5th-wheel trailers
GVWR up to 30,000 lbs.; towing up to 10,000 lbs.
Compatible with OEM cooler systems
33% more efficient than a comparable tube and fin design

from

$65.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Imperial Econo-Kool tube and fin transmission cooler
Size: 3/4″ x 10″ x 15-7/8″
Class “A” motor homes, large travel trailers, 5th-wheel trailers
GVWR up to 26,000 lbs.; towing up to 10,000 lbs.
Compatible with OEM cooler systems
Ultrasonically soldered for reliability
100% pressure testing to 150 PSI for quality assurance
High efficiency turbulators
Compatible with OEM cooler systems
Ultrasonically soldered for reliability
100% pressure testing to 150 PSI for quality assurance
High efficiency turbulators

from

$80.99

The Imperial Maxi-Cool XL’s plate and fin design offer excellent cooling efficiency in a compact, space-efficient design.

Product Features:

Imperial Rapid-Cool plate and fin transmission cooler
Size: 3/4″ x 11″ x 9-1/2″
Pickup trucks and vans, class “C” motor homes, travel trailers to 24′
GVWR up to 24,000 lbs.; towing up to 5,000 lbs.
33% more efficient than a comparable tube and fin design
Compatible with OEM cooler systems
Made with the highest quality materials
100% pressure testing to 150 PSI for quality assurance
33% more efficient than a comparable tube and fin design

from

$83.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Imperial high-performance transmission cooler
Size: 3/4″ x 7-1/2″ x 15-7/8″
SAE 45-degree fittings for maximum reliability
Electrostatic powder-coated to prevent corrosion
Up to Class C motorhomes, towing up to 5,000 pounds
SAE 45 degree fittings for maximum reliability
Electrostatically powder coated to prevent corrosion
All aluminum lightweight construction

from

$25.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Transmission cooler reinstallation kit
Contains part numbers 248001, 226201, 240250 and 4 hose clamps
Provides all hardware for reinstallation of Imperial transmission coolers
Contains nylon mounting rods, foam pads, locking buttons, hose and fitting
Made of high grade nylon for easy installation
Removable buttons for cooler/fan relocation
Made for both transmission coolers and electric fan installation
Comes with Quick Connect coupler

from

$67.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Imperial high-performance transmission cooler
Size: 3/4″ x 7-1/2″ x 12-1/2″
SAE 45-degree fittings for maximum reliability
Electrostatic powder-coated to prevent corrosion
SAE 45 degree fittings for maximum reliability
Electrostatically powder coated to prevent corrosion
All aluminum lightweight construction
SAE 45 degree fittings for maximum reliability
Electrostatically powder coated to prevent corrosion
All aluminum lightweight construction

from

$66.99

This automatic transmission oil cooler hose assembly is designed to match the fit and function of an original assembly. It is engineered from durable components as a reliable replacement for leaking or damaged lines on specified vehicles.

Product Features:

Direct replacement – this automatic transmission oil cooler hose assembly is designed to match the fit and function of the original equipment assembly on specified vehicle makes, models and years
Ideal solution – engineered to help ensure proper transmission cooling when the original assembly is leaking or has failed from corrosion, collision, vibration, or fitting damage
Durable construction – made of quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$43.99

Direct replacement – this automatic transmission oil cooler hose assembly is designed to match the fit and function of the original equipment assembly on specified vehicle makes, models and years
Ideal solution – engineered to help ensure proper transmission cooling when the original assembly is leaking or has failed from corrosion, collision, vibration, or fitting damage
Durable construction – made of quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$112.99

Direct replacement – this automatic transmission oil cooler hose assembly is designed to match the fit and function of the original equipment assembly on specified vehicle makes, models and years
Ideal solution – engineered to help ensure proper transmission cooling when the original assembly is leaking or has failed from corrosion, collision, vibration, or fitting damage
Durable construction – made of quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$65.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Imperial Econo-Kool tube and fin transmission cooler
Size: 3/4″ x 7-1/2″ x 15-7/8″
Pickup trucks and vans, class “C” motor homes, travel trailers to 24′
GVWR up to 22,000 lbs.; towing up to 5,000 lbs.
Compatible with OEM cooler systems
Ultrasonically soldered for reliability
100% pressure testing to 150 PSI for quality assurance
High efficiency turbulators
Compatible with OEM cooler systems
Ultrasonically soldered for reliability
100% pressure testing to 150 PSI for quality assurance
High efficiency turbulators

from

$151.99

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

Imperial Econo-Kool tube and fin transmission cooler
Size: 1-1/2″ x 12″ x 15 1/8″
Severe-duty transmission oil cooling applications
Towing with class “A” motor home or towing more than 10,000 lbs.
Compatible with OEM cooler systems
Ultrasonically soldered for reliability
100% pressure testing to 150 PSI for quality assurance
High efficiency turbulators

from

$83.99

Direct replacement – this automatic transmission oil cooler hose assembly is designed to match the fit and function of the original equipment assembly on specified vehicle makes, models and years
Ideal solution – engineered to help ensure proper transmission cooling when the original assembly is leaking or has failed from corrosion, collision, vibration, or fitting damage
Durable construction – made of quality materials for reliable performance and long service life
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$119.99

New Platinum Pro Automatic Transmission Oil Cooler Assembly

Product Features:

Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

Top Picks for 2006 Ford F-450 Super Duty Transmission Mounts

Upgrade Ford F-450 Super Duties with top-quality Transmission Mounts parts, including 3 OEM and aftermarket selections for your 2006 model.

show more show less

from

$27.99

The purpose of the mount is to support the engine and transmission on the chassis and dampen vibration and noise from reverberating to the rest of the vehicle. Engine and Transmission Mounts are engineered and manufactured to meet or exceed OEM specifications using the latest CAD/CAM engineering process to ensure superior quality, form, fit and function. Only premium quality materials are used in the manufacturing process to guarantee precise performance and maximum durability. Applicable to FORD 94-10; LINCOLN 06-10;. Please verify your application.

Product Features:

MAXIMUM LIFE & PERFORMANCE: Both natural and SBR (Styrene Butadiene) rubber provide good abrasion resistance and aging stability to ensure maximum life and performance.
MEETS OR EXCEEDS DUROMETER MEASUREMENTS: All rubber material is manufactured to specific Durometer (hardness) measurements based on the vehicle’s application requirements.
HARDENED STEEL FASTENERS: All fasteners are made of hardened steel with heat treated Grade #5 bolts.
SUPERIOR BOND: A special Chemlock® bonding agent is used to ensure a superior rubber-to-metal bond.
HYDRAULIC MOUNT DESIGN: Hydraulic Mounts (applicable where OE) are designed for most front wheel drive vehicles because transverse drive train mounting.
For Years: 1994-2010
Weight approx: 4 Lbs
MOUNT HOLES ON CENTER: 5.56 INCH/141.22 MM
STUDS ON CENTER: 2.30 INCH/58.42 MM
HEIGHT: 2.69 INCH/68.33 MM
STUDS AND MOUNT OFFSET: 0.25 INCH/6.1 MM
STUD THREAD: M12X1.75

from

$33.99

The purpose of the mount is to support the engine and transmission on the chassis and dampen vibration and noise from reverberating to the rest of the vehicle. Engine and Transmission Mounts are engineered and manufactured to meet or exceed OEM specifications using the latest CAD/CAM engineering process to ensure superior quality, form, fit and function. Only premium quality materials are used in the manufacturing process to guarantee precise performance and maximum durability. Applicable to FORD 99-07; LINCOLN 03-06;. Please verify your application.

Product Features:

MAXIMUM LIFE & PERFORMANCE: Both natural and SBR (Styrene Butadiene) rubber provide good abrasion resistance and aging stability to ensure maximum life and performance.
MEETS OR EXCEEDS DUROMETER MEASUREMENTS: All rubber material is manufactured to specific Durometer (hardness) measurements based on the vehicle’s application requirements.
HARDENED STEEL FASTENERS: All fasteners are made of hardened steel with heat treated Grade #5 bolts.
SUPERIOR BOND: A special Chemlock® bonding agent is used to ensure a superior rubber-to-metal bond.
HYDRAULIC MOUNT DESIGN: Hydraulic Mounts (applicable where OE) are designed for most front wheel drive vehicles because transverse drive train mounting.
For Years: 1999-2007
Weight approx: 5 Lbs

from

$63.99

The purpose of the mount is to support the engine and transmission on the chassis and dampen vibration and noise from reverberating to the rest of the vehicle. Engine and Transmission Mounts are engineered and manufactured to meet or exceed OEM specifications using the latest CAD/CAM engineering process to ensure superior quality, form, fit and function. Only premium quality materials are used in the manufacturing process to guarantee precise performance and maximum durability. Applicable to FORD 03-07;. Please verify your application.

Product Features:

MAXIMUM LIFE & PERFORMANCE: Both natural and SBR (Styrene Butadiene) rubber provide good abrasion resistance and aging stability to ensure maximum life and performance.
MEETS OR EXCEEDS DUROMETER MEASUREMENTS: All rubber material is manufactured to specific Durometer (hardness) measurements based on the vehicle’s application requirements.
HARDENED STEEL FASTENERS: All fasteners are made of hardened steel with heat treated Grade #5 bolts.
SUPERIOR BOND: A special Chemlock® bonding agent is used to ensure a superior rubber-to-metal bond.
HYDRAULIC MOUNT DESIGN: Hydraulic Mounts (applicable where OE) are designed for most front wheel drive vehicles because transverse drive train mounting.
For Years: 2003-2007
Weight approx: 4 Lbs

In-Demand Transmission Bearings for 2006 Ford F-450 Super Duties

Select from 5 premium Transmission Bearings parts for your 2006 Ford F-450 Super Duty, with prices ranging from $14.99 to $47.99.

show more show less

from

$14.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$23.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$26.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$47.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$46.99

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Most Sold 2006 Ford F-450 Super Duty Transmission Seals

Explore our best-selling Ford parts for the 2006 F-450 Super Duty among 10 OEM and aftermarket options starting from $3.99.

show more show less

from

$30.99

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -40 Deg F to 400 Deg F / -40 Deg C to 204 Deg C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$6.99

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$25.49

Design type: spring loaded; single-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$18.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$314.99

ManTransBrg-SealKit

from

$39.99

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$29.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$14.29

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 400 Deg. F / -40 Deg. C to 204 Deg. C
Excellent high temperature capabilities
Compatible with wide range of fluids
Delivers quality and reliable performance for every type of repair

from

$10.49

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$3.99

Shift Shaft O-Ring

Top-Rated Transmission Parts Brands For Your 2006 Ford F-450 Super Duty

Shop for the best-rated brands offering Transmission Parts and other products for your 2006 Ford F-450 Super Duties. Below you’ll find some of our best rated Transmission Parts from National, Dorman, and Imperial, and more. Transmission Parts from these brands that fit a 2006 F-450 Super Duty start at just $6.99 and are rated as high as 4.3 stars. OEM and aftermarket Transmission Parts don’t get more top quality, durable, and affordable than from the brands below.

Popular National 2006 Ford F-450 Super Duty Transmission Parts

When it comes to maintaining or upgrading your 2006 Ford F-450 Super Duty, using quality Transmission Parts is essential to ensure durability and a perfect fit. National ticks all of those boxes. We offer a wide selection of National Transmission Parts, specifically designed for the 2006 Ford F-450 Super Duty. With over 2 National brand Transmission Parts in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $14.99, with an average price of just $19.49. Plus, with over 10 customer reviews and an average rating of 4.3 stars, you can trust that our National Transmission Parts will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $14.99

(3)

Bearing Race

“Used on my diesel truck”

from $23.99

(7)

Tapered Roller Bearing Cone

“Good price”

Popular Dorman 2006 Ford F-450 Super Duty Transmission Parts

Dorman auto parts is one of the highest quality Transmission Part brands in the market. Any 2006 Ford F-450 Super Duty owner should feel confident when installing genuine Dorman parts in their vehicle. To ensure the best fit and performance for your 2006 F-450 Super Duty, Advance Auto Parts carries a full inventory of 3 Dorman Transmission Parts. Plus you will be keeping your Ford in peak condition while saving money because prices on these Dorman Transmission Parts range from $6.99 to $22.99, plus, with more than 24 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Transmission Parts below will deliver on both quality and value.

from $6.99

(3)

Shift Tube Lever Pin

“Fit right and the rubber piece holds it in place like it should. The rubber on my old one was no longer flexible enough or had worn down so it no long”

from $7.99

(17)

Steering Column Shift Tube Bushing 2 Piece

“Take your time. It works, Just be patient.”

from $22.99

(4)

Shift Clamp And Bushing

“For a Dorman part, it was actually pretty good.”

FAQs for 2006 Ford F-450 Super Duty Transmission Parts

Which Transmission Parts are best-sellers for 2006 Ford F-450 Super Duties?

Out of 111 Transmission Parts that fit 2006 Ford F-450 Super Duties, the following parts are the top sellers:

Steering Column Shift Tube And Plunger Assembly (26949799) – $56.99
Steering Column Shift Tube Bushing 2 Piece (10478045) – $7.99
Pedal and Shift Linkage Bushing Assortment (9110078) – $11.99

What’s the price range for 2006 Ford F-450 Super Duty Transmission Parts?

Transmission Part prices for the 2006 Ford F-450 Super Duty start at $3.99 and go up to $2,924.99 for the most premium parts.

What’s the average price of a Transmission Part for a 2006 Ford F-450 Super Duty?

The average price for Transmission Parts for the 2006 Ford F-450 Super Duty is $286.96. Keep in mind the variety of part types within our Transmission Part category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Transmission Parts for other Ford F-450 Super Duty model years?

Yes, we currently carry Transmission Parts for 24 model years of Ford F-450 Super Duties between 1999 and 2024. Transmission Parts are bought most frequently for the following model years: 2022, 2021, 2020, 2019, 2018, 2017, 2016, 2015, and 2014.

What are the cheapest Transmission Parts for my 2006 Ford F-450 Super Duty?

The cheapest 2006 Ford F-450 Super Duty Transmission Parts we carry in stock are:

Shift Shaft O-Ring (12009712) – $3.99
Shift Lever Pin Assembly (50247693) – $5.99
Automatic Transmission Shift Tube Bushing (12541334) – $6.49
Shift Tube Lever Pin (11187951) – $6.99
Multi-Purpose Seal (18444989) – $6.99

What are the top-rated Transmission Parts that fit the 2006 Ford F-450 Super Duty?

Out of 969 reviews by customers, our 2006 Ford F-450 Super Duty Transmission Parts have an average customer rating of . These are some of the highest-rated Transmission Part types for the 2006 Ford F-450 Super Duty and their top-rated products:

Transmission Cooler and Parts
- High Performance Transmission Oil Cooler (15230020) – $85.99
- Maxi-Kool® XL Transmission Oil Cooler (12031443) – $73.99
- Transmission Oil Cooler (10711782) – $400.99
Transmission Electrical Parts
- High Performance Transmission Oil Cooler (15230020) – $85.99
- Maxi-Kool® XL Transmission Oil Cooler (12031443) – $73.99
- Transmission Oil Cooler (10711782) – $400.99
Automatic Transmission Pan and Gaskets
- High Performance Transmission Oil Cooler (15230020) – $85.99
- Maxi-Kool® XL Transmission Oil Cooler (12031443) – $73.99
- Transmission Oil Cooler (10711782) – $400.99

What types of Transmission Parts do you sell for my 2006 Ford F-450 Super Duty?

As of 11/2/25, these are some of the most in-demand types of Transmission Parts for a 2006 Ford F-450 Super Duty:

Can I get help with 2006 Ford F-450 Super Duty Transmission Part orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Transmission Parts and more.

What is your return policy for Ford F-450 Super Duty Transmission Parts?

Advance Auto Parts keeps returns simple. For new Ford F-450 Super Duty Transmission Parts and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2006 Ford F-450 Super Duty Transmission Parts

Carquest Premium – Multi-Use Connector (Part No.PTA1023)

National – Bearing Race (Part No.2520)

KAI – Trans Oil Cooler Assembly (Part No.FO4050131)

LuK – Pre-Filled Hydraulic Clutch Release System (Part No.CRS023)

Dorman – Transmission Drain Plug – M10 -1.5 (sold by each) (Part No.090-206)

Dorman – Help – Shifter Cable Bushing Kit (OE Fix) (Part No.14908)

FAG US – Cone (Part No.K387-A)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T6R1406711T4P)

Dorman – Shifter Select Lever (Part No.905-109)

National – Manual Transmission Output Shaft Seal (Part No.710719)

National – Multi-Purpose Seal (Part No.7929S)

Dorman – Help – Odometer Shift Cap (Part No.49298)

NTK – Automatic Transmission Fluid Temperature Sensor (Part No.AT0020)

ATP – AT CONTR SOLENOID (Part No.FE-6)

Dorman – Remanufactured Transmission Solenoid Pack (Part No.609-023)

Imperial – Maxi-Kool XL Transmission Oil Cooler (Part No.243012)

Dorman – TRANSMISSION COOLER (Part No.918-299)

aFe POWER – Transmission Pan (Part No.46-70120-1)

Dorman – Transmission Oil Pan: Direct Fit, Steel, 20 Quart (Part No.265-822)

Dorman – Steering Column-Shift Tube Damper (Part No.905-095)

Imperial – Transmission Line Fitting Kit (Part No.240394)

Imperial – Transmission Line Fitting Kit (Part No.240395)

National – Bearing Race (Part No.M802011)

Tech Smart – Automatic Transmission Shift Tube Bushing (Part No.Q18002)

Carquest Premium – Automatic Transmission Shift Tube Bushing (Part No.QBA1001)

Dorman – Steering Column Shift Tube Bushing 2 Piece (Part No.905-107)

Dorman – Steering Column Shift Tube Bushing Kit (Sold by kit) (Part No.905-103)

Dorman – Steering Column Shift Tube Bushing 2 Piece (Part No.905-107)

Dorman – Shift Clamp And Bushing (Part No.905-110)

Dorman – Shift Tube Lever Pin (Part No.924-440)

Tech Smart – Automatic Transmission Shift Tube Bushing (Part No.Q18002)

Dorman – Steering Column-Shift Tube Damper (Part No.905-095)

Dorman – Help – Odometer Shift Cap (Part No.49298)

Dorman – Steering Column Shift Tube And Plunger Assembly (Part No.905-102)

Dorman – Help – Shifter Cable Bushing Kit (OE Fix) (Part No.14908)

Dorman – Shift Tube Lever Plunger Shaft (Part No.905-555)

ATP – AT CONTR SOLENOID (Part No.FE-6)

ATP – AT CONTR SOLENOID (Part No.FE-7)

ATP – AT CONTR SOLENOID (Part No.FE-8)

Shift Pro by ETE – 5R110W Automatic Transmission Assembly (Part No.T162605)

Shift Pro by ETE – 5R110W Automatic Transmission Assembly (Part No.T162604)

Shift Pro by ETE – 5R110W Automatic Transmission Assembly (Part No.T162607)

Shift Pro by ETE – 5R110W Automatic Transmission Assembly (Part No.T162606)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106003T4P)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106003T2)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106805T2P)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106003T4)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106805T4P)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106805T2)

Premium Drive Train – Premium Remanufactured Automatic Transmission Assembly (Part No.T5R1106805T4)

Dorman – Steering Column Shift Tube Bushing Kit (Sold by kit) (Part No.905-103)

Imperial – High Performance Transmission Oil Cooler (Part No.240516)

Imperial – Maxi-Kool® XL Transmission Oil Cooler (Part No.243007)

Dorman – Transmission Oil Cooler (Part No.918-216)

Imperial – Maxi-Kool XL Transmission Oil Cooler (Part No.243012)

Imperial – Econo-Kool Transmission Oil Cooler (Part No.241018)

Imperial – Plate and Fin Style Transmission Cooler, Heavy Duty, 3/4" x 9-1/2" x 11" (Part No.243008)

Imperial – High Performance Transmission Oil Cooler (Part No.240514)

Imperial – Transmission Oil Cooler Reinstallation Kit (Part No.248002)

Imperial – High Performance Transmission Oil Cooler (Part No.240512)

Dorman – Transmission Oil Cooler Line (Part No.624-542)

Dorman – Transmission Oil Cooler Line (Part No.624-545)

Dorman – Transmission Oil Cooler Line: Exact Fit, Metal/Rubber (Part No.624-885)

Imperial – Econo-Kool Transmission Oil Cooler (Part No.242016)

Imperial – Transmission Oil Cooler (Part No.241015)

Dorman – Transmission Oil Cooler Line (Part No.624-578)

KAI – Trans Oil Cooler Assembly (Part No.FO4050104)

Anchor – Transmission Mount: Rear, 1 Piece (Part No.2884)

Anchor – Transmission Mount: Rear, 1 Piece (Part No.2971)

Anchor – Transmission Mount: Rear, 1 Piece (Part No.3284)

National – Bearing Race (Part No.M802011)

National – Tapered Roller Bearing Cone (Part No.M802048)

National – Bearing Race (Part No.2520)

National – Tapered Roller Bearing Cone (Part No.2580)

FAG US – Cone (Part No.K387-A)

National – Multi Purpose Seal (Part No.100712V)

National – Multi-Purpose Seal (Part No.7929S)

National – Multi-Purpose Seal (Part No.710485)

National – Multi-Purpose Seal (Part No.710718)