from

$38.99

Product Features:

Side adjuster
Fits Toyota V6 and Landcruiser reverse rotation front

from

$6.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$549.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 8″ and V6
Made from 9310 steel for added strength
Works with stock side gears in standard carrier case

from

$8.51

Axle Seal

from

$123.99

Product Features:

Fits Toyota V6 rear
Conversion yoke for 29 spline gears
29 spline pinion

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$14.99

T100 & Tacoma w/LOC pinion nut.

Product Features:

Pinion nut
Fits Toyota Tacoma and T100 with factory locking differential

from

$36.56

With Clamps and Grease The EMPIRE CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function. Install one boot kit per wheel to restore vehicle to optimal condition and protect the constant velocity joint from contamination

Product Features:

Help restore the vehicle to like-new condition
Constructed of high strength OE materials
Resists environmental contamination
Protects the CV joint from premature failure

from

$39.99

8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:

Pinion depth shim kit for Toyota 7.5″, 8″ and V6

from

$11.99

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$51.99

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$78.99

Product Features:

Seal housing for Toyota 8″ and V6
Includes o-rings

from

$919.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

Fits Toyota V6 rear
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$6.99

Toyota 7.5″, 8″, & V6 ring gear bolt retainer plate (5 needed).

Product Features:

Ring gear bolt retainer plate for Toyota 7.5″ 8″ and 8″ V6
5 needed

from

$299.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. This kit fits applications with a 27 spline pinion.

Product Features:

Fits Toyota V6 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$2.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$11.99

Toyota 8″ & V6 gasket.

Product Features:

Dropout gasket
Fits Toyota 8″ and V6

from

$24.29

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$89.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$18.99

Product Features:

Bulkhead quit connect fitting

from

$491.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. This kit fits applications with a 29 spline pinion.

Product Features:

Fits Toyota V6 rear
29 spline only
Included are KOYO bearings and races along with high quality seals and small parts.
Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and gasket.

from

$36.99

Product Features:

Bulkhead fitting kit
Includes bulkhead fitting, outer fitting and o-ring

from

$10.99

Product Features:

Rear axle bearing snap ring for Toyota 7.5″, 8″ and V6

from

$873.99

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install..

Product Features:

Easier installation – this loaded axle assembly includes a new axle shaft, wheel bearing, hub and backing plate pre-assembled and ready to install right out of the box.
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components
Simpler solution – eliminates the need to use potentially dangerous shop press to perform complete bearing repair
Trustworthy quality – backed by engineers and inspectors in the United States, with decades of aftermarket experience

from

$41.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$140.51

NSK guarantees the high quality of all of their products by repeated, rigorous bench testing, and other checks that take full advantage of their cutting-edge technology, which only the major bearing manufacturers can offer. Double-row angular or taper contact ball bearing with integral high performance seal. Easy and reliable preload settings and include a simple mounting process with no spacer required. Hub bearings utilize an integral high-performance seal and feature a compact design with no grease packing required. NSK Hub unit bearings are designed to meet increasingly strict requirements that demand lighter weight, greater promotion of fuel efficiency, and enhanced module production systems.

Product Features: