Name: Differential Cover
Brand: aFe POWER
SKU: 46-70370
Price: 289.99 USD

from

$289.99

aFe Power’s new rear differential cover brings performance engineering to the protection of your axle’s differential. This differential cover is constructed out of durable A356-T6 cast aluminum with reinforcing ribs for maximum strength. Mounting hardware is included for a hassle-free installation. A calibration plug set to the factory level prevents overfilling of the differential. A magnetic drain plug and a deep reach magnetic fill plug are provided for maximum protection. This cover has a raw finish with machined fins for a distinctive look. 4 Quart Gear Oil Capacity: This cover has about a 4 quart gear oil capacity at the factory fill level, factory cover holds about 3 quarts. Built-in External Fins: Built-in external fins transfer heat from the fluid to the outside air for maximum cooling. Magnetic Drain/Fill Plug: This system incorporates a magnetic drain and deep reach fill plug that captures loose particles for maximum rear-end protection. Oil Level calibration plug: A 1/8″ NPT calibration plug is set to the factory fluid level which eliminates accidental overfilling. When it comes to engineering for power, performance, protection and value, aFe Power is the only choice.

Product Features:

Constructed of Durable A356-T6 Cast Aluminum
Reinforcing Ribs w/ a Raw Finish and Machined Fins
Magnetic Drain and Fill Plugs Capture Loose Particles
Calibration Plug Set to Factory Fluid Level

from

$13.99

Product Features:

PINION SHIM – DANA 70 ALL

from

$137.90

Differential Bearing

from

$15.99

O-ring for left hand carrier bearing adjuster for 9.25″ GM IFS.

Product Features:

Axle o-ring
Fits Chrysler 9.25″ IFS

from

$208.99

11.5AAM GM & Chrysler (fits All Years) UNIVERSAL standard Open spider gear kit.

Product Features:

Spider gear kit
Fits GM and Chrysler 11.5″ open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$98.99

Left hand carrier bearing adjuster for 9.25″ GM IFS.

Product Features:

Side adjuster
Fits 2010 and down GM 9.25″ IFS
Left hand side

from

$6.49

This drive axle shaft lock C-clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$1.89

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$134.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$309.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$244.99

Yukon yoke for GM 8.25″ IFS and 9.25″ IFS (mech 3R). 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside snap rings. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.25″ IFS and 9.25″ IFS
30 spline
Mechanics 3R u-joint size
Inside snap ring design
2.556″ snap ring span
1.125″ cap diameter
Strap style

from

$28.99

Long shaft inner clip for 9.25″ GM IFS.

Product Features:

Stub axle snap ring
Fits GM 9.25″ IFS

from

$17.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$40.99

Product Features:

Side gear spacer sleeve
Fits GM 9.25″ IFS

from

$8.19

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$103.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 88-12; GMC 94-12;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1988-2012
Weight approx: 3 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
WITHOUT PLATE
WITH STUDS

from

$439.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2010 and down GM and Chrysler 11.5″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$8.02

Differential Drain P

from

$172.25

More like a complete kit than a single part, Dorman’s Four-Wheel Drive (4WD) Actuator comes with all the parts needed to complete the repair. Since this part is a direct replacement, the exact fit adds another layer of efficiency and convenience.

Product Features:

Includes all necessary gaskets and seals (where applicable)
Sealed for leak resistance
Engineered for durability against harsh road and weather conditions, including water intrusion
Quality tested to ensure trouble free installation and performance

from

$317.99

Yukon standard open spider gear kit for 9.5″ GM rear and ’06 and earlier GM 9.25″ IFS with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 9.5″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$11.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$110.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$14.79

Product Features:

Brand may vary by location

from

$779.99

11.5″ GM standard Open case, loeaded.

Product Features:

Standard open carrier case and spiders
Fits GM and Chrysler 11.5″

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$23.99

Product Features:

Cross pin bolt
Fits GM 9.5″ and 9.25″ IFS

from

$439.99

RING & PINION SET

from

$386.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!