from

$198.99

NO RETURN HM807046 SET-UP Bearing (1 SINGLE Bearing) for Dana 80 , 11.5AAM , 4.125″ OD .

Product Features:

Set up bearing
Fits HM807046 pinion bearing
Easily slips on and off pinion journal to allow for pinion depth adjustment

from

$304.99

Yukon 1480 Lifetime Series U/Joint. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.

Product Features:

Clutch kit
Fits GM 10.5″ 14 bolt truck with Eaton positraction
Carbon fiber clutches

from

$2026.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$184.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

GM 14 BOLT 10.5 RING GEAR 98 & ON

from

$9.86

Differential Cover G

from

$462.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2011 and up GM and Chrysler 11.5″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$98.99

Left hand carrier bearing adjuster for 9.25″ GM IFS.

Product Features:

Side adjuster
Fits 2010 and down GM 9.25″ IFS
Left hand side

from

$34.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$55.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$10.30

Differential Drain P

from

$7.99

14T side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits GM 10.5″ 14 bolt truck

from

$46.99

11.5″ GM standard Open cross pin shaft.

Product Features:

Cross pin shaft
Fits GM 11.5″

from

$3.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$37.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$60.23

SKF is a supplier of original equipment wheel bearings, hubs and seals to most of the world’s leading automakers. Engineered and manufactured to the highest quality standards, SKF wheel bearings greatly reduce friction and increase load-carrying capabilities. With an ability to boost reliability under heavy loads and misaligned conditions, SKF wheel bearings offer an ideal solution for many wheel end applications.

Product Features:

Precision bearing pre-load and correct application of advanced manufacturing techniques such as orbital rolling
100% tested to the actual OE specifications per part number for fit, form and function
High quality steel and surface finishes
Proper implementation of heat treatment

from

$859.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

Fits GM 10.5″ 14 bolt truck
Installs into standard open carrier
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$539.99

Yukon Performance steel spool for GM 14T with 30 spline axles. fits 4.10 and down. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 10.5″ 14 bolt truck with 30 spline axles
4.10 and down ratio only or 4.56 and up thick gears
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$221.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$23.99

Product Features:

Cross pin bolt
Fits GM 9.5″ and 9.25″ IFS

from

$596.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$39.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$317.99

Yukon standard open spider gear kit for 9.5″ GM rear and ’06 and earlier GM 9.25″ IFS with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 9.5″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$74.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$1485.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM and Chrysler 11.5″ with 30 spline axles
Clutch style positraction
Smooth design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA