from

$14.99

New Standard Replacement A/C Receiver Drier

Product Features:

Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$57.99

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

from

$28.49

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

Ideal for rigid cast aluminum parts
Meets OEM Specifications
Sensor safe & non-corrosive
Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
Blowout resistant, allowing leakproof gaskets to be made in just one minute
Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

from

$17.49

Permatex’s The Right Stuff 90 Minute Series offers the fastest return to service in a in just 90 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 90 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 90 minutes

from

$61.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. This thermostat will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features:

High grade stainless steel and copper construction
Meets or exceeds OEM standards
Consistent and precise response to cooling system needs
Original equipment design for worry-free direct fit replacement
100% tested and calibrated

from

$68.59

Intelligent control systems from MAHLE are used in millions of applications worldwide to provide needs-based precision temperature control. Simple, effective, and tried and tested millions of times over: thermostat inserts from MAHLE provide meticulous regulation of coolant circuits around the world up to approximately 20 m3/h, and ensure ideal operating temperatures in light vehicles, trucks, stationary engines, and also agricultural and construction machinery. Wax elements are at the heart of all MAHLE thermostats and thermostat inserts. These maintenance-free, durable elements have proved their worth in millions of applications. MAHLE, Manufactures a wide range of variants with actuating forces of between 30 N and 2,500 N, small or large displacements, and for a large number of regulation ranges within a temperature span of -20C to +130C.

Product Features:

OE quality and design
Maintenance-free, durable elements

from

$187.78

Valeo manufactures a direct fit Heater Core that guarantees OEM quality, fit and performance.

Product Features:

OEM Quality Direct fit Application
Meets or exceeds OEM specifications.
Utilizes the factory style mounts, connectors and fittings.
Provides exceptional reliability.

from

$6.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$6.99

Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings. Permatex Water Pump & Thermostat has the highest water-glycol resistance available in an RTV silicone.

Product Features:

Sensor-safe, noncorrosive RTV silicone gasket material
Formulated specifically for water pumps and thermostat housings
Highest water-glycol resistance available in RTV silicone
Superior adhesion and flexibility
Can be used as a gasket maker or dressing

from

$55.99

New Standard Replacement A/C Expansion Valve

Product Features:

Meets All Federal Motor Safety Standards
No Drilling Needed For Installation
No Modifications Needed For Installation
Direct Fit Replacement For Your Vehicle
Same Form Fit And Function As OE
Check Out The Large Selection Of Parts Available For Your Vehicle

from

$62.99

For more than a century, Delphi has been making the parts cars are born with – often developing new technologies in the process. Delphi is proud of its OE heritage, and over the years they’ve used that experience to expand into a global aftermarket supplier.

Product Features:

Designed digital output for maximum signal to noise ratio. Not impacted by temperature changes and provide robust, long-lasting sensor protection. Manufactured to meet or exceed OE requirements.

from

$68.99

Designed digital output for maximum signal to noise ratio. Not impacted by temperature changes and provide robust, long-lasting sensor protection. Manufactured to meet or exceed OE requirements.

Product Features:

Delphi sensors are built to meet or exceed OE requirements and testing
Delphi has improved the OE design by plating the connectors to help prevent corrosion and failure commonly caused by internal and cable short circuits
Delphi’s OE design helps by preventing mechanical damage to the sensor wheel, soiling and increased wheel bearing free play
Speed sensors maintain optimal performance during drastic temperature changes for robust, long-lasting sensor protection
Designed digital output for maximum signal to noise ratio

from

$62.99

Advance Auto Parts is committed to providing high-quality ABS sensors. The entire manufacturing process is closely managed to deliver high quality products.

Product Features:

High grade materials that are equal to or better than OE provide durability and long service life
All ABS sensors are tested for proper fit, form, and function
Wire diameter and sheathing same or larger than OE to ensure product quality
Glass filled reinforced plastic for superior resistance to automotive fluids, dirt, salt and road debris
Includes all necessary brackets and hardware

from

$9.99

This relay connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

Direct replacement – this relay connector matches the appearance and function of the factory hardware on specified applications
Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$39.49

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
Brass sensor housing precision machined to meet or exceed OE thermal conductivity
OE precision matched thermistor position for correct output parameters
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$32.99

OEM specified. Designed specially for high-torque and high vibration applications, like those common in import engines, this premium RTV gasket maker exceeds manufacturers’ performance requirements. Sensor-safe, low odor, and non-corrosive. Maximum vibration resistance, with outstanding resistance to oils, cooling and shop fluids. Temperature range -65ºF to 500ºF (-54 Deg. C to 260 Deg. C) intermittent.

Product Features:

Designed specially for high-torque and high vibration applications
Maximum vibration resistance with outstanding resistance to oils, cooling and shop fluids
OEM specified
Low-odor, non-corrosive formula
Temperature Range: -65 Deg. F to 500 Deg. F (-54 Deg. C to 260 Deg. C)

from

$19.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute