2004 Honda Civic Belts and Hoses
More 2004 Honda Civic Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2004 Honda Civic, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2004 Honda Civic Belts and Hoses
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17.5" Long, 1.06" Diameter (Part No.E72577)
from
$28.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.23326)
from
$30.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Serpentine Idler/Tensioner Pulley; Direct Fit, 76 mm Diameter, 7 Grooves (Part No.89008)
from
$36.49
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 20.4mm Width, 4 Grooves (Part No.89029)
from
$57.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter (Part No.900027A)
from
$28.99
This pulley is manufactured by Litens Automotive the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- OE-spec sealed ball bearings with synthetic grease and double lip seals for long life
Dayco – Serpentine Idler/Tensioner Pulley; Steel, 74mm Dia., 17mm Width, 4 Grooves (Part No.89185)
from
$50.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Dayco, Acc. Belt Idler Pulley (Part No.G60201221083DAY)
from
$31.33
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision bearing
- OE High quality pulley assembly
- Durable long life performance.
Dayco – Idler Pulley (Part No.89073)
from
$45.99
Dayco No Slack Idler/Tensioner Pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and therefore longer belt life. This pulley includes lifetime lubricated ball bearings and double high temperature seals to assure peak bearing performance, the most critical element of a pulley’s service life. This specific V-Belt driven, steel pulley contains a specially formulated e-coating, comparable to OE plating that resists corrosion and wear resistance under harsh environments.
Product Features:
See More
Product Features:
- Lifetime lubricated ball bearings
- Double high temperature seals to assure peak bearing performance
- V-Belt, steel pulley that contains a specially formulated e-coating, comparable to OE plating that resists corrosion and wear resistance under harsh environments
- Meets or exceeds OE quality
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 7 Inch Length (Part No.87618)
from
$18.29
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, .50" Diameter (Part No.B70944)
from
$8.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.23697)
from
$56.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17.75" Long, 1.06" Diameter (Part No.D70808)
from
$17.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Dayco, Acc. Belt Tensioner Assy, Automatic (Part No.G6001985745DAY)
from
$118.58
Dayco, Acc. Belt Tensioner Assy, Automatic
Dorman – Automatic Belt Tensioner (Tensioner Only) (Part No.419-380)
from
$109.99
This accessory drive belt tensioner assembly is designed to match the fit of an original equipment assembly on specified vehicles. It is engineered to help ensure proper belt tension when an original belt is slipping, broken, or worn from fatigue.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt tensioner assembly is designed to match the fit of an original equipment assembly on specified vehicles
- Ideal solution – engineered to help ensure proper belt tension when an original belt is slipping, broken, or worn from fatigue
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
ContiTech – Drive V-Belt (Part No.W1000655835CON)
from
$11.75
All ContiTech V-Belts are quiet, OE-quality and virtually service free. The only time these belts require attention is during installation. Designed to be oil-resistant and temperature-stable from -22F to 176F (30C to 80C), ContiTech V-Belts are open-flanked, toothed, and shaped for greater traction and torque. High performance construction features include a synthetic fiber fabric cover, a special polyester cord designed to permit tightly controlled shrink, plus a polychloroprene rubber body, integrally molded cogs, and raw edges.
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Polyester fiber tensile members and a ribbed belt design.
Gates – Automotive XL« High Capacity V-Belt (Part No.7385)
from
$26.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Premium Molded Heater Hose (Part No.18700)
from
$15.29
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Dayco, Heater Hose (Part No.R3030329305DAY)
from
$16.94
Dayco, Heater Hose
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length (Part No.86835)
from
$7.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Dayco – Poly Rib Belt Serpentine Belt; 32.09 Long, 4 Rib Count (Part No.5040320)
from
$33.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Aramid Cord Poly Rib Belt Serpentine Belt; 67.32 Long, 7 Rib Count (Part No.A070673)
from
$40.99
The Dayco poly-V aramid belt is engineered to maintain a quiet, vibration-free belt drive system, especially for higher output OE engines that require an aramid belt. Unlike polyester-corded belts, this aramid cord belt is designed to resist the expected elongations, especially during high accessory loading. This unique feature of length stability and minimal stretch aids in difficult drives where span vibrations and tensioner movements are excessive. The Dayco aramid cord poly rib belt is built with Dayco’s specially designed EPDM rubber compounds to resist cracking and perform better under extreme temperature ranges.
Product Features:
See More
Product Features:
- Designed for applications with an OEM aramid belt and is specifically helpful for those with noise, vibration or harshness issues, or in-drive systems in which tensioner take-up is minimal
- Length stability resists excessive span vibrations or tensioner movements
- Features special compounds that resist cracking and perform well under intense engine temperatures
Driveworks – Poly Rib Belt Serpentine Belt; 61.02 Long, 6 Rib Count (Part No.610K6)
from
$23.99
The Driveworks belt is designed to provide better belt-to-pulley contact. The specialized rubber compound incorporates a high temperature polymer formulated to maximize load carrying requirements and belt life. This Driveworks ribbed belt has been constructed and engineered to meet the stringent demands of today’s automotive drive systems. The Driveworks ribbed belt delivers long-lasting dependable belt life.
Product Features:
See More
Product Features:
- Constructed with heat and ozone resistant EPDM rubber
- Fiber is added to the rib stock to reinforce the rubber and reduce noise from worn and misaligned pulleys
- Made with treated polyester cord to reduce belt stretch
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 23.5" Long, 1.13" Diameter (Part No.E72433)
from
$33.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Premium Molded Coolant Hose (Part No.23303)
from
$25.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 15" Long, 1.19" Diameter (Part No.E72403)
from
$18.29
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 18.5" Long, 1.19" Diameter (Part No.E72584)
from
$27.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Popular 2004 Honda Civic Belts and Hoses Categories
2004 Honda Civic Belts and Hoses
You count on your 2004 Honda Civic to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 54 Belts and Hoses ranging in price from $0.99 to $264.99, you’re sure to find everything you need for your 2004 Honda Civic.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 12 different brands like Dayco, Driveworks, and Litens. 2004 Honda Civic Belts and Hoses start as low as $0.99!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 985 extensive product reviews on 2004 Honda Civic Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length with 4.3 stars and Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.06" Diameter with 4.9 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2004 Honda Civic below to get started!
Top-Rated Belts and Hoses Brands For Your 2004 Honda Civic
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2004 Honda Civic running right for years to come. In our inventory you’ll find brands like Dayco, Driveworks, Litens, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 2004 Honda Civic back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2004 Honda Civic, and some of our most reviewed Dayco parts include:
from
$25.99
(75)
Serpentine Idler/Tensioner Pulley; Direct Fit, 76 mm Diameter, 37 mm Smooth
Idler Pulleys
from
$36.49
(60)
Serpentine Idler/Tensioner Pulley; Direct Fit, 76 mm Diameter, 7 Grooves
Belt Tensioner Pulleys
FAQs for 2004 Honda Civic Belts and Hoses
What are the most purchased Belts and Hoses for the 2004 Honda Civic?
Out of 54 Belts and Hoses for the 2004 Honda Civic, the most popular in our inventory are:
from
$57.99
(27)
Serpentine Idler/Tensioner Pulley; Steel, 70mm Dia., 20.4mm Width, 4 Grooves
Belt Tensioner Pulleys
What are the top-rated 2004 Honda Civic Belts and Hoses?
Top-rated Belts and Hoses for your 2004 Honda Civic based on customer reviews/ratings are:
from
$23.49
(14)
Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length
“Hose fit perfectly.”
from
$22.99
(11)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 17" Long, 1.06" Diameter
“in stock, exact fit as published”
