2003 Toyota Sequoia Drivetrains

Below you will find various in-demand Toyota Drivetrains, components and accessories for your 2003 Sequoia. Advance Auto Parts has popular Sequoia parts like Differentials, Transfer Cases, 4WD Components and more. You’ll also find aftermarket and OEM Drivetrains for other Sequoia model years including 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022 and more. Select a category of 2003 Toyota Sequoia Drivetrains below and start saving instantly.

Popular 2003 Toyota Sequoia Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

4WD Actuator Switches

U-Joints

Drive Shaft and Axles

Differential Open Unit and Components

Differential Covers

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Pinion Flanges

Differential Axle Shafts

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

OE CV Boot Kits

Differential Pinion Pilot Bearings

Transfer Case Output Shaft Seals

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Lock Sensors

Axle Vents

Rear Axle Shaft Bearings

Differential Ring and Pinions

CV Quick Boot Kits

Spindle Lock Nuts

Drive Shaft Repair Kits

Differential Spools

Automatic Transmission Differential Cover Gaskets

Differential Pinion Bearing Kits

Differential Seals

Differential Drain Plugs

Differential Ring Gear Bolts

Differential Carrier Bearing Shims

Input Shaft Seals

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

CV Joint Half Shaft Seals

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Axle Shaft Bearing Retainers

Limited Slip Differential Assemblies

Essential Drivetrains for 2003 Toyota Sequoias

from

$73.99

Product Features:

Cross pin shaft
Fits Toyota Tacoma and T100

from

$51.99

This drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle.
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.19

SHAFT SEAL

from

$32.99

This CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself.
Ideal solution – this kit is a reliable replacement for original components that have failed due to wear.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$125.99

Yukon yoke for ’04 and older Toyota Tacoma and T100 with 30 spline. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 2004 and down Toyota Tacoma and T100
30 spline
60mm x 60mm bolt pattern

from

$22.99

Product Features:

Bearing retainer
Fits 2001-2002 Toyota 4Runner, 2001-2004 Tacoma and 2000-2006 Tundra

from

$23.99

07 and up Tundra front pinion nut.

Product Features:

Pinion nut
Fits 2007 and up Toyota Tundra front

from

$404.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Toyota T100 & Tacoma rear without factory locking differential
8.125″ ring gear diameter
30 spline pinion
12 ring gear bolts
4.88 ratio

from

$19.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$236.58

Wheel Hub Assembly

from

$15.99

Ring Gear bolt for Toyota T100, Tacoma & 8″ IFS front. 12mm x 1.0.

Product Features:

Ring gear bolt for Toyota T100 and Tacoma rear without factory locking differential and Toyota Clamshell front
12mm x 1.0

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$6.79

This engine oil drain plug is designed to match the fit and function of an original equipment plug on specified vehicles. It is engineered to replace a missing or damaged plug & help ensure a secure seal.

Product Features:

Direct replacement – this engine oil drain plug is designed to match the fit and function of an original equipment plug on specified vehicles.
Ideal solution – engineered to replace a missing or damaged plug and help ensure a secure seal
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$36.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Compatible with most oils and EP lubricants at higher operating temperatures
High resistance to oxidation and ozone and has low swell in hydrocarbon fluids
Temperature range: -20°F to 300°F; -29°C to 149°C
National® oil seals are recognized worldwide for their quality and reliable performance for every type of repair.

from

$42.25

Transfer Case Switch

from

$1044.99

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.

Product Features:

Pre-Pressed Rear Axle.
Pre-Pressed Rear Axle.
Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.
Easier installation – this loaded axle assembly includes a pre-assembled new axle shaft, wheel bearing, hub and backing plate
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components

from

$21.99

Product Features:

KIT SHIM SIDE 9.5″ GM

from

$22.49

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$20.29

Product Features:

CRUSH SLEEVE TOY. FRT END

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$759.99

Differential

from

$23.99

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue.
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$542.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$101.99

7.5″ V6 & 4cyl side shim kit (incl. 7 shims).

Product Features:

Carrier shim kit
Fits Toyota 7.5″

from

$42.99

Product Features:

TOYOTA 8″ V6&4CLY TURBO

from

$12.79

Formulated to meet the specific requirements of Toyota, Lexus, and Scion vehicles equipped with conventional (non-CVT) transmissions that require the use of Toyota ATF WS. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF WS is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Optimized viscosity and advanced friction reducing additive technology provide exceptional fuel economy performance
Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Exceptional wear protection of gears and bearings
Provides superior deposit control and protects metal surfaces from rust and corrosion
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

from

$47.99

Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.

Product Features:

Matches OE form, fit and function
One piece neoprene boot
Kit complete with boot, grease, and hardware for complete installation
Hardware matches original design requirements
Application specific for this vehicle

from

$379.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. No side shims.

Product Features:

Fits reverse rotation Toyota 7.5″
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush, and silicone.

Upgrade your 2003 Toyota Sequoia with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2003 Toyota Sequoia, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Toyota or enhancing its overall performance, Drivetrains are key to keeping your Sequoia functioning at its best. At Advance Auto Parts, we offer a wide selection of 138 Drivetrains for the 2003 Toyota Sequoia, designed to meet your needs without breaking the bank. From Differential replacements to Transfer Cases upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2003 Toyota Sequoia at great prices. Our Drivetrains inventory for this model ranges from just $5.49 to $899.99, with an average price of $176.54. Our 138 Drivetrains in stock come from 27 trusted brands, so you’re sure to find the right part for your 2003 Toyota Sequoia without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2003 Toyota Sequoia, we stock popular OEM and aftermarket Drivetrains from top names like Valvoline, Royal Purple, Moog, and more. Valvoline Drivetrains start at just $12.49 and boast an impressive 5 stars average rating from customers. Royal Purple and Moog also bring quality to the table, with Drivetrains available starting at $12.99, and at an average 5 stars rating. With 1,656 customer reviews and counting, our 2003 Toyota Sequoia Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2003 Toyota Sequoia is always ready to roll. We’re committed to providing you with everything you need to keep your Sequoia in top shape, all in one place. Start shopping confidently below for your 2003 Toyota Sequoia!

Best-Selling Differentials for 2003 Toyota Sequoias

Enhance the driving experience in your Toyota with 89 quality Differential components, starting at $5.49.

show more show less

from

$14.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$12.99

High Performance Motor Oil API LICENSED MOTOR OIL Royal Purple High Performance Motor Oil combines premium base oils with proprietary additive technologies to create a high performance synthetic engine oil that optimizes performance and protection. Royal Purple High Performance Motor Oils carry the current API and ILSAC engine oil licenses, as well as the GM dexos1 gasoline engine oil approval. ILSAC GF-6 AND GM DEXOS1 Modern gasoline direct injection (GDI) engines have achieved levels of power and fuel economy never before possible in passenger car engines. As a result, smaller engines operate at much higher loads across all engine speeds. This has caused increased wear in critical areas of the engine, and created a destructive phenomenon called low-speed pre-ignition (LSPI). The unique, state-of-the-art additive technology in Royal Purple High Performance engine oils is designed specifically to address these issues, and help engines maintain performance and reliability.

Product Features:

Better Wear Protection
Increased Protection against Low Speed Pre-Ignition
Increased Fuel Efficiency
Better Protection for Vehicle Exhaust Emissions Equipment
Improved Compatibility with Fuels Containing Ethanol
Superior Corrosion Protection
Made in USA

from

$35.99

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$25.99

Max Gear is recommended for truck and automotive differentials, outboard motor lower units or in rear axles or manual transmissions requiring an API fluid. Max Gear is a high performance automotive gear oil designed to provide maximum protection to heavily loaded gears while increasing power throughput through the drive train. Max Gear virtually eliminates both gear and bearing wear-even under severe squeeze film conditions caused by extremely high loads, sudden shock loads or low RPMs. Slippery, synthetic molecules not only reduce wear and friction but significantly increase Max Gear’s cold weather fluidity and lubricity, making it the ideal choice for vehicles operating in cold climates. Gears run smoother, quieter, cooler and longer without overhauls. It is noncorrosive to both ferrous and nonferrous metals.

Product Features:

Maximizes horsepower
Extends gear and bearing life
Reduces operating temperature
Lower coefficient of friction
Superior corrosion protection
Separates rapidly from water
For use with open, limited-slip and locking differential
Contains limited-slip friction modifier
Made in USA

from

$69.99

Valvoline SAE 75W-140 Full Synthetic Gear Oil provides the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Engineered to outperform, our formulation provides exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity and wear resistance, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. It’s recommended for conventional rear axles and transmissions requiring EP gear lubes under high speed, high load, high torque and high horsepower conditions.

Product Features:

EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -22F to 390F degrees
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
FIGHTS CORROSION AND RUST with emulsifying agents and safeguards against impurities, oxidation and thermal breakdown
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$51.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$89.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$14.99

Valvoline Multi-Vehicle Transfer Case Fluid is a full synthetic product meeting the performance needs for transfer cases recommending Ford XL-12 and GM Auto Trak II specifications or ATF fluids (DEX/MERC, ATF +4, etc).

Product Features:

Recommended for use in most Ford, GM and FCA (Dodge, Jeep) models
Formulated to help prevent gear wear and protect against rust and corrosion
Formulated to deliver enhanced protection against deposits
Helps provide better protection during extreme operating conditions

from

$11.79

Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

from

$9.99

Toyota 7.5 pinion nut (M18x1.5).

Product Features:

Pinion nut for Toyota 7.5″
18mm x 1.5 thread

from

$37.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$19.99

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations
EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$12.99

Royal Purple HMX SAE 5W-30 High-Mileage Synthetic Motor Oil, 1 quart is specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles. Formulated with robust zinc/phosphorus anti-wear compounds combined with Royal Purple’s proprietary additive technology Synerlec, HMX is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines. In addition, HMX is fortified with stout detergents to remove engine build-up and deposits, maintain cleanliness and promote engine longevity.

Product Features:

Specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles
Formulated with robust zinc/phosphorus anti-wear compounds combined with royal purple’s proprietary additive technology
Hmx is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines
Reduces friction and metal-to-metal contact for peak engine performance
Also provides outstanding oxidation resistance to safely extend oil drain intervals, and an ionic attraction to metal surfaces, providing protection and minimizing wear at start-up
High-Mileage Formula: Specifically designed for engines with more than 75,000 miles, this full synthetic engine oil helps minimize wear and restore lost performance.

from

$15.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.49

Product Features:

CRUSH SLEEVE 12 BLT CAR

from

$6.79

Direct replacement – this engine oil drain plug is designed to match the fit and function of an original equipment plug on specified vehicles.
Ideal solution – engineered to replace a missing or damaged plug and help ensure a secure seal
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$24.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$9.99

Product Features:

Brand may vary by location

from

$107.99

When the thin-gauge steel corrodes on Sequoia, Tacoma, Tundra truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.

Product Features:

Rear Differential Cover.
Rear Differential Cover.
When the thin-gauge steel corrodes on Sequoia, Tacoma, Tundra truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.
Direct replacement – this weld-on differential cover directly replaces a corroded original cover on certain Sequoia, Tacoma and Tundra trucks
Cost-effective repair – rather than buy a new axle, cut off the old cover and weld on this new one

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$13.49

Product Features:

KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$42.25

Transfer Case Switch

from

$9.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$6.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$16.99

Toyota T100 & Tacoma crush sleeve. Approx 2.325″ long.

Product Features:

Crush sleeve for Toyota Tacoma and T100 without factory locker
2.235″ tall

from

$12.29

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$15.99

Ring Gear bolt for Toyota T100, Tacoma & 8″ IFS front. 12mm x 1.0.

Product Features:

Ring gear bolt for Toyota T100 and Tacoma rear without factory locking differential and Toyota Clamshell front
12mm x 1.0

from

$461.99

Yukon standard open spider gear kit for Toyota T100 & Tacoma with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Toytoa Tacoma and T100 open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin spider gear thrust washers.

from

$394.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits Toyota T100 & Tacoma rear without factory locking differential
8.125″ ring gear diameter
30 spline pinion
12 ring gear bolts
4.56 ratio

from

$246.99

Yukon yoke for Toyota 7.5″ IFS (and ’85 and newer rear) with 23 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota 7.5″
23 spline

from

$144.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Toyota Tacoma and T100 without factory locking differential
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$27.99

Pinion preload shim for Toyota T100. One single shim. 0.033″ thick. Two needed. Fits against crush sleeve.

Product Features:

Fits Toyota T100 and Tacoma
0.140″ thick

from

$19.99

Pinion seal for 7.5″, 8″, V6, and T100 and Tacoma with lockers.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Toyota 7.5″, 8″ with 4 cylinder engine, V6, Landcruiser and Tacoma/T100 with factory locking differential

from

$17.99

Product Features:

Pinion depth shims for Dana Spicer 60 and 70U

from

$15.99

Toyota T100 & Tacoma pinion nut.

Product Features:

Pinion nut
Fits Toyota Tacoma and T100 without factory locking differential

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$518.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$16.99

Toyota 7.5″ crush sleeve, 2.185″ long.

Product Features:

Crush sleeve for Toyota 7.5″
2.185″ tall

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$288.99

Product Features:

TOY 10BL 7.5 R/P 5.29 IFS MG

from

$899.99

Replacing a worn wheel bearing usually requires a time consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.

Product Features:

Easier installation – this loaded axle assembly includes a new axle shaft, wheel bearing, hub and backing plate pre-assembled and ready to install right out of the box.
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components.
Simpler solution – eliminates the need to use potentially dangerous shop press to perform complete bearing repair
Quality tested – this part has undergone try-on, corrosion and material testing to ensure a quality fit and long service life

from

$898.99

Easier installation – this loaded axle assembly includes a new axle shaft, wheel bearing, hub and backing plate pre-assembled and ready to install right out of the box.
Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components.
Simpler solution – eliminates the need to use potentially dangerous shop press to perform complete bearing repair
Quality tested – this part has undergone try-on, corrosion and material testing to ensure a quality fit and long service life

from

$759.99

Differential

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$669.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 7.5″
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

Top Picks for 2003 Toyota Sequoia 4WD Components

Upgrade Toyota Sequoias with top-quality 4WD Components parts, including 1 OEM and aftermarket selections for your 2003 model.

show more show less

from

$311.99

This 4WD actuator directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:

Direct replacement – this 4WD axle actuator directly replaces the original equipment part on specific vehicle years, makes and models.
Effective fix – installation addresses inoperative four-wheel drive caused by failed original actuator.
Smart solution – delivers reliable fit and function for competitive price
Trustworthy quality – backed by team of designers and engineers in the United States

In-Demand Drive Shafts and Axles for 2003 Toyota Sequoias

Select from 21 premium Drive Shafts and Axles parts for your 2003 Toyota Sequoia, with prices ranging from $6.99 to $883.99.

show more show less

from

$35.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$11.99

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles.
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue.
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$162.99

All CARQUEST axles have a new zinc dichromate plated nut or attaching hardware. CV joint grease has a high moly content. The boot bands are made from stainless steel, and the boots are manufactured to resist wear and damage due to extreme high and low temperatures.High moly CV joint grease with stainless-steel boot bands

from

$10.79

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$20.49

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$21.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$6.99

This axle vent is designed to match the fit and function of the original vent on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this axle vent is designed to match the fit and function of the original vent on specified vehicles.
Restores functionality – reliable replacement for an original vent that has failed due to blockage or fatigue.
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$51.99

Direct replacement – this drive shaft repair kit is designed to match the original hardware required to repair the drive shaft on specified vehicle.
Ideal solution – this kit is a reliable replacement for original components that have failed due to fatigue.
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$125.99

Yukon yoke for ’04 and older Toyota Tacoma and T100 with 30 spline. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 2004 and down Toyota Tacoma and T100
30 spline
60mm x 60mm bolt pattern

from

$46.99

Toyota 01-06 Sequoia rear inner axle seal.

Product Features:

Inner axle seal
Fits 2001-2006 Toyota Sequoia rear

from

$807.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$682.99

Driveshaft – Front

from

$606.99

The original drive shafts on specific vehicles have permanently staked universal joints that make servicing difficult. This Dorman OE FIX rear drive shaft makes the U-joints serviceable for simpler maintenance. Every Dorman part is backed by over 100 years of experience, along with a dedicated team of product experts, automotive engineers and technical support specialists based in the United States. We are passionate about giving repair professionals and vehicle owners greater freedom to fix cars and trucks, which is why we have more than 100,000 parts in our catalog today and promise to never stop driving new solutions.

Product Features:

Rear Driveshaft Assembly
Rear Drive Shaft: Greaseable, Adjustable, OE Fix
Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation
Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance

from

$529.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$389.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$320.86

WHEEL BEARING ASSEMB

from

$236.58

Wheel Hub Assembly

from

$44.99

SPICER U-JOINT

from

$22.99

Product Features:

Bearing retainer
Fits 2001-2002 Toyota 4Runner, 2001-2004 Tacoma and 2000-2006 Tundra

from

$7.19

SHAFT SEAL

Most Sold 2003 Toyota Sequoia Universal Joints

Explore our best-selling Toyota parts for the 2003 Sequoia among 15 OEM and aftermarket options starting from $15.99.

show more show less

from

$28.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$35.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$19.99

Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$32.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$25.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$27.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$62.99

from

$76.99

Yukon U/Joint for many Toyota applications. 2.047″ snap ring span, 1.142″ cap diameter. Inside snap ring.

from

$72.43

Spicer Drivetrain Products light-duty U-joints feature journal crosses that are manufactured from high-quality alloy forgings and heat-treated for maximum life. The bearing cups are case-hardened for strength and durability, while the seals are crafted from nitrile rubber for optimum grease retention and contaminant exclusion. Ample grease reservoirs in each trunnion assure effective lubrication; they’re pre-filled with high-quality synthetic lithium grease, providing superior friction-reduction and resistance to higher temperatures. These replacement universal joints are available for dozens of positions, as well as greasable and non-greasable styles. Order the model designed for fitment with your vehicle and engine type.

Product Features:

Forged cross
Lubeable
O.E.M replacement
Snap rings

from

$29.43

Forged cross
Lubeable
O.E.M replacement
Snap rings

from

$43.92

Forged cross
Lubeable
O.E.M replacement
Snap rings

from

$19.40

U Joint

Top-Rated Drivetrains Brands For Your 2003 Toyota Sequoia

Shop for the best-rated brands offering Drivetrains and other products for your 2003 Toyota Sequoias. Below you’ll find some of our best rated Drivetrains from Valvoline, Royal Purple, and Moog, and more. Drivetrains from these brands that fit a 2003 Sequoia start at just $12.49 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Valvoline 2003 Toyota Sequoia Drivetrains

When it comes to maintaining or upgrading your 2003 Toyota Sequoia, using quality Drivetrains is essential to ensure durability and a perfect fit. Valvoline ticks all of those boxes. We offer a wide selection of Valvoline Drivetrains, specifically designed for the 2003 Toyota Sequoia. With over 6 Valvoline brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $12.49, with an average price of just $27.99. Plus, with over 419 customer reviews and an average rating of 5 stars, you can trust that our Valvoline Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$14.49

(2)

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

“I’ve used this in my 2005 2500HD since I bought the truck with 20k on it now at 280k changed every other year maybe 40k I’d put on in two years,
I pu”

from
$19.99

This product is not rated

Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-140, 1 Quart

“”

from
$12.49

This product is not rated

High Performance Transmission & Differential Gear Oil: Conventional 75W-90, 1 Quart

“”

Popular Royal Purple 2003 Toyota Sequoia Drivetrains

Royal Purple auto parts is one of the highest quality Drivetrain brands in the market. Any 2003 Toyota Sequoia owner should feel confident when installing genuine Royal Purple parts in their vehicle. To ensure the best fit and performance for your 2003 Sequoia, Advance Auto Parts carries a full inventory of 3 Royal Purple Drivetrains. Plus you will be keeping your Toyota in peak condition while saving money because prices on these Royal Purple Drivetrains range from $12.99 to $25.99, plus, with more than 139 customer reviews and an impressive 5 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from
$12.99

(82)

High Performance SAE 5W30 Synthetic Motor Oil, API Certified, 1 QT

“best oil”

from
$12.99

This product is not rated

HMX SAE 5W-30 High-Mileage Synthetic Engine Oil (1 Quart)

“”

from
$25.99

(57)

MaxGear SAE 75W140 High Performance Gear Oil w/Friction Modifier Additive, 1 QT

“Good Quality and OK price!”

FAQs for 2003 Toyota Sequoia Drivetrains

Which Drivetrains are best-sellers for 2003 Toyota Sequoias?

Out of 138 Drivetrains that fit 2003 Toyota Sequoias, the following parts are the top sellers:

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (12079201) – $14.49
Greaseable Premium Universal Joint (10086900) – $19.99
Universal Joint (10265714) – $15.99

What’s the price range for 2003 Toyota Sequoia Drivetrains?

Drivetrain prices for the 2003 Toyota Sequoia start at $5.49 and go up to $899.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2003 Toyota Sequoia?

The average price for Drivetrains for the 2003 Toyota Sequoia is $176.54. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Toyota Sequoia model years?

Yes, we currently carry Drivetrains for 24 model years of Toyota Sequoias between 2001 and 2025. Drivetrains are bought most frequently for the following model years: 2022, 2021, 2020, 2019, 2018, 2017, 2016, 2015, and 2014.

What are the cheapest Drivetrains for my 2003 Toyota Sequoia?

The cheapest 2003 Toyota Sequoia Drivetrains we carry in stock are:

Differential Crush Sleeve (20520217) – $5.49
Taper Bearing Cup (15050072) – $6.49
Standard Engine Oil Drain Plug: 9/16-18 Thread, 0.75 " Head, 1 Pack (22149658) – $6.79
Differential Carrier Gasket (5723698) – $6.79
Oil Seal (15440111) – $6.79

What are the top-rated Drivetrains that fit the 2003 Toyota Sequoia?

Out of 1,656 reviews by customers, our 2003 Toyota Sequoia Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 2003 Toyota Sequoia and their top-rated products:

Universal Joints
- Greaseable Super Strength Universal Joint (10087062) – $35.99
- Universal Joint (10855076) – $28.99
- Non-Greaseable Super Strength Universal Joint (10087061) – $32.99
4WD Components
- Greaseable Super Strength Universal Joint (10087062) – $35.99
- Universal Joint (10855076) – $28.99
- Non-Greaseable Super Strength Universal Joint (10087061) – $32.99

What types of Drivetrains do you sell for my 2003 Toyota Sequoia?

As of 2/5/25, these are some of the most in-demand types of Drivetrains for a 2003 Toyota Sequoia:

Can I get help with 2003 Toyota Sequoia Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Toyota Drivetrains and more.

What is your return policy for Toyota Sequoia Drivetrains?

Advance Auto Parts keeps returns simple. For new Toyota Sequoia Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2003 Toyota Sequoia Drivetrains

Yukon Gear – T100 & Tacoma Standard Cross Pin Shaft (Part No.33417)

Dorman – Drive Shaft Repair Kit – Only Fits Dorman Driveshafts (Part No.932-988)

FAG US – SHAFT SEAL (Part No.SS2881)

Dorman – Uni-Fit C.V. Joint Boot Kit Outer greater than 3.58 In. Diameter (Part No.614-003)

Yukon Gear – Yoke For ’04 And Older Toyota Tacoma And T100 With 30 Spline (Part No.41103)

Yukon Gear – Toyota Bearing Retainer For ’01-’02 4Runner, ’01-’04 Tacoma & 00-’06 Tundra (Part No.33421)

Yukon Gear – 07 And Up Tundra Front Pinion Nut (Part No.33159)

USA Standard Gear – Ring & Pinion Gear Set For Toyota T100 And Tacoma In A 4.88 Ratio (Part No.36240)

Driveworks – Taper Bearing Cone (Part No.S-HM-88649)

Autopart International Inc – Wheel Hub Assembly (Part No.K70011990141API)

Yukon Gear – Ring Gear Bolt For Toyota T100, Tacoma & 8" IFS Front (Part No.33059)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

Needa Parts – Standard Engine Oil Drain Plug: 9/16-18 Thread, 0.75 " Head, 1 Pack (Part No.090-030)

National – Oil Seal (Part No.710931)

FAE – Transfer Case Switch (Part No.J7101947097FAE)

Dorman – Pre-Pressed Rear Axle (Part No.926-176)

Motive Gear – Differential Carrier Shim Kit (Part No.GM9.5SSK)

National – Multi Purpose Seal (Part No.710114)

Motive Gear – Differential Crush Sleeve (Part No.3121)

Yukon Gear – T100 & Tacoma Roll Pin (Part No.33420)

Yukon Gear – Differential (Part No.26050)

Dorman – Front Wheel Bearing Hub Nut (Part No.926-263)

Dorman – Front Drive Shaft: Adjustable (Part No.938-738)

Yukon Gear – Carrier Shim Kit For Toyota 7.5" (Part No.55038)

Motive Gear – Differential Gear Install Kit (Part No.TOYV6IK)

Idemitsu – Type TLS-LV Automatic Transmission Fluid – 1 qt (Part No.10114-042B)

Beck/Arnley – Cu Boot Kit (Part No.103-2872)

Yukon Gear – Master Overhaul Kit For Toyota 7.5" IFS Differential For T100, Tacoma, And Tundra (Part No.14115)

Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)

Royal Purple – High Performance SAE 5W30 Synthetic Motor Oil, API Certified, 1 QT (Part No.01530)

Valvoline – DEX/MERC Automatic Transmission Fluid, 1 Gallon (Part No.773636)

Royal Purple – MaxGear SAE 75W140 High Performance Gear Oil w/Friction Modifier Additive, 1 QT (Part No.01301)

Valvoline – SynPower Transmission & Differential Gear Oil: Full Synthetic 75W-140, 1 Gallon (Part No.887344)

National – Bearings (Part No.32307)

National – Bearings (Part No.30025)

Valvoline – Transfer Case Fluid, 1 Quart (Part No.855459)

Idemitsu – Type TLS Automatic Transmission Fluid – 1 qt (Part No.10106-042K)

Yukon Gear – Toyota 7.5 Pinion Nut (Part No.33155)

National – Shaft Repair Sleeve (Part No.99157)

Valvoline – Flex Fill Transmission & Differential Gear Oil: Full Synthetic 75W-140, 1 Quart (Part No.889787)

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

Royal Purple – HMX SAE 5W-30 High-Mileage Synthetic Engine Oil (1 Quart) (Part No.11744)

National – Bearings (Part No.HM88610)

Motive Gear – Differential Crush Sleeve (Part No.3954480)

Needa Parts – Standard Engine Oil Drain Plug: 9/16-18 Thread, 0.75 " Head, 1 Pack (Part No.090-030)

National – Multi Purpose Seal (Part No.710525)

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

Driveworks – Differential Pinion Seal (Part No.S-710525)

Dorman – Rear Differential Cover (Part No.926-958)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

Motive Gear – Differential Pinion Shim Kit (Part No.1109)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

FAE – Transfer Case Switch (Part No.J7101947097FAE)

Driveworks – Oil Seal (Part No.S-1177)

Felpro – Differential Carrier Gasket (Part No.RDS 55428)

Yukon Gear – Toyota T100 & Tacoma Crush Sleeve (Part No.33120)

Motive Gear – Pinion Seal (Part No.1177)

Yukon Gear – Ring Gear Bolt For Toyota T100, Tacoma & 8" IFS Front (Part No.33059)

Yukon Gear – Standard Open Spider Gear Kit For Toyota T100 & Tacoma With 30 Spline Axles (Part No.16133)

Yukon Gear – High Performance Ring & Pinion Gear Set For Toyota Tacoma And T100 In A 4.56 Ratio (Part No.24537)

Yukon Gear – Yoke For Toyota 7.5" IFS (And ’85 And Newer Rear) With 23 Spline Pinion (Part No.41106)

Yukon Gear – Minor Install Kit For Toyota T100 And Tacoma Rear Differential (Part No.12069)

Yukon Gear – Pinion Preload Shim For Toyota T100 (Part No.55075)

Yukon Gear – Pinion Seal For Toyota 7.5", 8", V6 & T100 (Part No.30005)

Yukon Gear – Replacement Pinion Depth Shims For Dana 60, 61 & D70-U (Part No.55012)

Yukon Gear – Toyota T100 & Tacoma Pinion Nut (Part No.33160)

Yukon Gear – T100 & Tacoma Roll Pin (Part No.33420)

Powertrax – No-Slip Traction System (Part No.9220803002)

Yukon Gear – Toyota 7.5" Crush Sleeve (Part No.33115)

Yukon Gear – Outer Oil Slinger (Part No.33025)

Motive Gear – Differential Ring and Pinion (Part No.TAC529IFS)

Dorman – Pre-Pressed Rear Axle (Part No.926-175)

Dorman – Pre-Pressed Rear Axle (Part No.926-174)

Yukon Gear – Differential (Part No.26050)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

USA Standard Gear – Spartan Locker For Toyota 7.5" With 27 Spline Axles, Includes Heavy-Duty Cross Pin Shaft (Part No.17014)

Driveworks – Taper Bearing Cup (Part No.S-HM-88610)

Driveworks – Taper Bearing Cone (Part No.S-HM-88649)

Driveworks – Oil Seal (Part No.S-223802)