2003 Chevrolet Express 1500 Drivetrains

Below you will find various in-demand Chevrolet Drivetrains, components and accessories for your 2003 Express 1500. Advance Auto Parts has popular Express 1500 parts like Universal Joints, CV Axles and Joints, Transfer Cases and more. You’ll also find aftermarket and OEM Drivetrains for other Express 1500 model years including 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014 and more. Select a category of 2003 Chevrolet Express 1500 Drivetrains below and start saving instantly.

Popular 2003 Chevrolet Express 1500 Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

U-Joints

Drive Shaft and Axles

Transfer Case Assemblies

Transfer Case Adapter Gaskets

Transfer Case Output Shaft Sensors

Transfer Case Gaskets

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Drive and Prop Shaft Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

U-Joint Centering Yokes

Differential Cover Bolts

Input Shaft Pilot Bearings

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Transfer Case Adapters

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Cover Plugs

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Ring and Pinions

Differential End Yokes

Differential Pinion Supports

Spindle Lock Nuts

Differential Lock Assemblies

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Axle Nuts

Rear Housing Cover Gaskets

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Drive Shaft Seals

Differential Seals

Axle Shaft Lock C-Clips

Bearing and Seal Overhaul Kits

Differential Drain Plugs

Differential Ring Gear Bolts

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Input Shaft Seals

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Engine Intermediate Shaft Bearings

Mounting Adapter Seals

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Differential Pinion Gear Washers

Output Shaft Pilot Bearings

Spindle Washers

Differential Ring and Pinion Kits

Limited Slip Differential Assemblies

Differential Spider and Pinion Gear Kits

Differential Clutch Pack Clips

Universal Joint Strap Bolts

Stub Axle Washers

Differential Bearing Adjuster Nut Lock Bolts

Differential Shifter Seals

Essential Drivetrains for 2003 Chevrolet Express 1500s

from

$12.52

Differential Drain P

from

$19.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$359.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$5.99

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$45.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$110.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$7.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$12.99

Royal Purple HMX SAE 5W-30 High-Mileage Synthetic Motor Oil, 1 quart is specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles. Formulated with robust zinc/phosphorus anti-wear compounds combined with Royal Purple’s proprietary additive technology Synerlec, HMX is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines. In addition, HMX is fortified with stout detergents to remove engine build-up and deposits, maintain cleanliness and promote engine longevity.

Product Features:

Specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles
Formulated with robust zinc/phosphorus anti-wear compounds combined with royal purple’s proprietary additive technology
Hmx is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines
Reduces friction and metal-to-metal contact for peak engine performance
Also provides outstanding oxidation resistance to safely extend oil drain intervals, and an ionic attraction to metal surfaces, providing protection and minimizing wear at start-up
High-Mileage Formula: Specifically designed for engines with more than 75,000 miles, this full synthetic engine oil helps minimize wear and restore lost performance.

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$121.99

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1988-2012
Weight approx: 2 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.60 INCH / 66 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
WITH PLATE
WITH STUDS
STYLE: ROUND FRAME

from

$6.49

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$32.99

Adjuster lock bolt for left hand case half of 7.2″ and 9.25″ GM IFS.

Product Features:

Side adjuster lock bolt
Fits GM 7.2″ IFS and 9.25″ IFS

from

$945.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$46.99

Product Features:

Thrust washer kit
Fits GM 7.2″ IFS

from

$1025.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM 9.5″
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$156.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$407.99

Yukon yoke for ’98 and newer GM 9.5″ with a 1350 U/joint size and triple lip design. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1998 and up GM 9.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$79.99

Product Features:

MINI INSTALL KIT-GM9.5/CHRY9.25 FRT

from

$32.99

Product Features:

Cross pin shaft
Fits GM 9.5″
Dura Grip positraction

from

$57.99

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

from

$29.99

9.5″ GM differential carrier Supershim kit.

Product Features:

Super carrier shim kit for GM 9.5″
Interlocking design makes installation much easier

from

$19.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$11.29

SHAFT SEAL

from

$23.99

Product Features:

Cross pin bolt
Fits GM 9.5″ and 9.25″ IFS

from

$173.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits GM 8.5″ rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$157.99

Product Features:

SUPER KIT-GM 8.5 TRUCK(LATE) TIMKEN INCLUDES AXLE BRGS & SEALS

Upgrade your 2003 Chevrolet Express 1500 with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2003 Chevrolet Express 1500, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Drivetrains are key to keeping your Express 1500 functioning at its best. At Advance Auto Parts, we offer a wide selection of 392 Drivetrains for the 2003 Chevrolet Express 1500, designed to meet your needs without breaking the bank. From Universal Joint replacements to CV Axles and Joints upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2003 Chevrolet Express 1500 at great prices. Our Drivetrains inventory for this model ranges from just $1.99 to $2,369.99, with an average price of $203.52. Our 392 Drivetrains in stock come from 30 trusted brands, so you’re sure to find the right part for your 2003 Chevrolet Express 1500 without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2003 Chevrolet Express 1500, we stock popular OEM and aftermarket Drivetrains from top names like Valvoline, Royal Purple, Moog, and more. Valvoline Drivetrains start at just $12.49 and boast an impressive 5 stars average rating from customers. Royal Purple and Moog also bring quality to the table, with Drivetrains available starting at $11.99, and at an average 5 stars rating. With 3,652 customer reviews and counting, our 2003 Chevrolet Express 1500 Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2003 Chevrolet Express 1500 is always ready to roll. We’re committed to providing you with everything you need to keep your Express 1500 in top shape, all in one place. Start shopping confidently below for your 2003 Chevrolet Express 1500!

Best-Selling Universal Joints for 2003 Chevrolet Express 1500s

Enhance the driving experience in your Chevrolet with 36 quality Universal Joint components, starting at $8.49.

show more show less

from

$15.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 330, 330A, 331 & 331A
Contains two 1.66″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$26.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging to provide higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting allows for easy maintenance and the flexible use of the entire assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals are applied to optimize grease retention and reduce contamination

from

$11.99

For U-Joints 355, 372 & 534G
Contains two 1.81″ bolt center clamps and four 5/16-24 x 1-5/16″ cap screws

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$50.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$36.99

Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$34.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$41.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$19.99

Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$32.49

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$11.49

This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles.
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$42.99

Backed by superior materials and rigorous testing, MOOG Anti-Galvanic universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installations.

Product Features:

INHIBITS GALVANIC REACTION — Designed specifically for aluminum yokes to avoid a galvanic reaction that leads to corrosion
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
CORROSION PROTECTION — Bearing cups and snap rings are chemically-coated to protect aluminum yokes
KEEPS DIRT OUT — Nitrile rubber grease seals with double lip design protects components from wear-causing contaminants
GREASABLE DESIGN — Radial design of bearing cups allows 360 Degrees lubricant distribution to all bearing surfaces to flush out contaminants and moisture to reduce corrosion and wear
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$54.03

Spicer Drivetrain Products light-duty U-joints feature journal crosses that are manufactured from high-quality alloy forgings and heat-treated for maximum life. The bearing cups are case-hardened for strength and durability, while the seals are crafted from nitrile rubber for optimum grease retention and contaminant exclusion. Ample grease reservoirs in each trunnion assure effective lubrication; they’re pre-filled with high-quality synthetic lithium grease, providing superior friction-reduction and resistance to higher temperatures. These replacement universal joints are available for dozens of positions, as well as greasable and non-greasable styles. Order the model designed for fitment with your vehicle and engine type.

Product Features:

Forged cross
Lubeable
O.E.M replacement
Snap rings

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$407.99

Fits 1998 and up GM 9.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$65.99

Yukon Mechanics 3R Lifetime Series U/Joint. 2.556″ span ring span, 1.125″ cap diameter. Inside snap ring.

from

$32.60

Designed and built by GMB to handle the highest loads and excessive torque found in pickups, SUVs, 4x4s and off road vehicles.

Product Features:

Elliptical bearing design delivers reliable performance under the heaviest of loads
Exclusive GMB Ultra-select bearing design exceeds OE specification
Precision finish trunnions and bearing surfaces ensure durability
Proven reliability in off-road conditions and harsh environments

from

$23.99

7.5″ and 8.5″ GM rear U/joint strap, Mech 3R.

Product Features:

u-joint strap
Fits GM 7.5″, 7.625″ and 8.5″
Mechanics 3R u-joint size
One single strap

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$449.99

Yukon yoke for GM 8.5″ with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″
30 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$359.99

Yukon forged yoke for GM 8.5″ with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″
30 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Forged steel

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$49.99

Universal Joint

from

$46.99

Yukon Mechanics 3R U/Joint. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring.

from

$38.93

An ACDelco Professional, premium aftermarket Universal Joint provides pivot points for driveshafts and is the ideal high-quality aftermarket replacement component for many vehicles on the road today. A universal joint is comprised of a pair of hinges connected at a right angle that transmits power between two driveshafts. This premium aftermarket replacement universal joint is manufactured to meet your expectations for fit, form, and function. ACDelco offers a full line of Professional, premium aftermarket Chassis Parts to keep vehicles riding and handling like new. With competitive warranty coverage and products covering all major chassis systems and alignment products for many vehicles on the road today, it’s no wonder the pros rely on ACDelco Professional, premium aftermarket Chassis Parts.

Product Features:

Pivot points for driveshafts in your vehicle
Comprised of a pair of hinges connected at a right angle
Premium, high-quality aftermarket part
Thoroughly engineered to meet or exceed your expectations for fit, form, and function
Provides the performance and dependability you expect from ACDelco

from

$18.10

U Joint

from

$17.99

U/joint strap kit, 10.25″, 9.5″, Dana 60, Dana 70, 1350 & 1410.

Product Features:

u-joint strap kit
Fits Ford 10.25″, GM 9.5″, Dana Spicer 60, 70, 70U and 70HD
1350 and 1410 u-joint size
Includes two straps and four bolts

from

$8.49

U/joint strap bolt for 14T, 7.5″, and 8.5″ GM.

Product Features:

u-joint strap bolt for GM 10.5″ 14 bolt truck, 7.5″ and 8.5″

Most Popular 2003 Chevrolet Express 1500 CV Axles and Joints

Customize your Chevrolet with 1 CV Axles and Joints products like Engine Intermediate Shaft Bearings, all priced under $14.49.

show more show less

from

$14.49

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:

Steel-backed Babbitt lining material
Used in automotive and high-performance
Babbitt is designed to perform under extreme loads w/o damaging other engine parts
Babbitt is more environmentally friendly than other material
ISO & QS certified manufacturing

Top Picks for 2003 Chevrolet Express 1500 Transfer Cases

Upgrade Chevrolet Express 1500s with top-quality Transfer Cases parts, including 26 OEM and aftermarket selections for your 2003 model.

show more show less

from

$15.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$11.99

Transfer case gasket warped and cracked? This replacement gasket restores a tight seal to prevent fluid leaks on certain vehicle years, makes and models.

Product Features:

Direct replacement – this transfer case gasket matches the fit and performance of the original gasket on specific vehicle applications.
Effective fix – restores a tight seal in the transfer case after original gasket fails.
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$21.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$59.99

ACDelco GM Original Equipment Vehicle Speed Sensor is a GM-recommended replacement component for one or more of the following vehicle systems: automatic transmission/transaxle, and/or manual drivetrain and axles. This original equipment sensor will provide the same performance, durability, and service life you expect from General Motors.

Product Features:

GM-recommended replacement part for your GM vehicle’s original factory component
Offering the quality, reliability, and durability of GM OE
Manufactured to GM OE specification for fit, form, and function

from

$42.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$14.73

Transfer Case Gasket

from

$7.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$106.99

This transfer case adapter replaces a damaged or cracked original equipment adapter, restoring a solid connection between the transmission and transfer case. Made of durable aluminum, this adapter includes a new gasket for a complete repair.

Product Features:

Ideal replacement – this transfer case adapter is a direct replacement for a damaged or cracked original equipment adapter.
Durable construction – manufactured from aluminum, this transfer case adapter is made to provide years of reliable service.
Complete solution – this adapter includes a new transfer case adapter gasket for a complete repair
Quality tested – this part has undergone try-on, corrosion and material testing to ensure a quality fit and long service life

from

$12.29

This transfer case adapter seal matches the fit and function of worn or damaged original equipment part. This seal should be replaced as part any service that requires the transfer case and transmission to be separated.

Product Features:

Ideal replacement – this transfer case adapter O-ring is a direct replacement for a worn or damaged original equipment seal between the transfer case and transmission.
Convenient on-hand part – this seal should be replaced whenever the transfer case is removed for service.
Application-specific design – this O-ring has been designed of durable materials specifically for this vehicle application
Quality tested – this part has undergone try-on and material testing to ensure a quality fit and long service life

from

$11.99

TCase Adapter Gasket

from

$49.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$19.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$8.99

ManTransExtHouseBush

from

$1674.99

Evolution Driveline products, are remanufactured to meet or exceed OEM specifications for quality, fit, and performance. Every transfer case we sell passes a comprehensive battery of tests on our computerized test center. We recreate actual driving conditions and analyze performance before the product even leaves the factory, so you can buy with confidence.

Product Features:

Back Lash, Mesh Load, Leak and Rotational Torque QC testing performed on each unit.
OEM cores are processed as individual units throughout the tear down and assembly process
Cores cleaned using our Hydro Blast cleaning and rinse process
All case halves wet sanded to ensure perfect mating surfaces
Loctite gasket eliminator and primer used to seal all aluminum mating surfaces
Remanufactured in our ISO9001:2008 USA facility.
Without Motor

from

$182.99

TRANSFER CASE PARTS

from

$142.99

TCaseBrg-SealKit

from

$64.47

Trans Case Output Sh

from

$35.99

GENERAL SEAL

from

$18.99

CONE

from

$17.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$11.29

CUP

from

$9.56

Trans Case Output Sh

from

$9.29

TCaseOutputShaftSeal

from

$5.99

TCaseInputShaftSeal

In-Demand Drive Shafts and Axles for 2003 Chevrolet Express 1500s

Select from 43 premium Drive Shafts and Axles parts for your 2003 Chevrolet Express 1500, with prices ranging from $5.29 to $883.99.

show more show less

from

$17.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$45.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$6.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$110.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$121.99

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1988-2012
Weight approx: 2 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.60 INCH / 66 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
WITH PLATE
WITH STUDS
STYLE: ROUND FRAME

from

$6.49

This drive axle shaft lock C-clip is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this drive axle shaft lock C-clip matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this clip is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$42.99

from

$44.99

from

$22.79

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$92.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CADI 02-06; CHEV 97-12; DODGE 03-06; FORD 11-15; GMC 96-12; NISSAN 04-22;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1996-2022
Weight approx: 2 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
WITHOUT PLATE
WITHOUT STUDS
EXTENDED DUST SHIELD

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$24.99

Product Features:

Fits GM 8.6″ and 9.5″
Sleeve to adapt standard yoke to use late model triple lip pinion seal

from

$103.99

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1988-2012
Weight approx: 3 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
WITHOUT PLATE
WITH STUDS

from

$89.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. axle bearing and seal kit for C10 Aero truck, 2.800″ OD, 1.620″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
2.800″ O.D.
1.620″ I.D.

from

$13.49

GM Genuine Parts Axle Shaft Bearings are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These bearings support and allow the axle shaft to rotate with minimal friction. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

Supports and allows the axle shaft to rotate with minimal friction
Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
GM regularly updates production and service part designs to integrate new materials and technologies

from

$17.00

Spindle Nut

from

$48.99

Product Features:

Brand may vary by location

from

$24.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Available in both caged design and full complement
Industry leading coverage
Professional technicians know they can depend on National

from

$11.99

Axle seal for ’88 and newer GM 8.5″ Chevy C10.Yukon Mighty seal.

Product Features:

Rear axle seal
Fits 1988 and up GM half ton truck
2.800″ O.D.
1.620″ I.D.

from

$10.99

9.5″ GM C/clip.

Product Features:

c-clip for GM 9.5″

from

$185.99

Drive shaft slip yoke vibrating, clunking or failed completely? This slip yoke directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:

Direct replacement – this drive shaft slip yoke directly replaces the original equipment yoke on specified vehicles
Effective fix – replacement restores safe, smooth driveline operation
Rigorously tested – designed and evaluated to assure safe, reliable operation
Trustworthy quality – backed by team of engineers and inspectors in the United States

from

$137.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$5.29

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 87-97; GMC 67-05; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2012
Weight approx: 1 Lbs
CUSHION INSERT ONLY
FOR COMPLETE MOUNT SEE PART 6056

from

$47.99

Product Features:

Brand may vary by location

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$8.49

Product Features:

Brand may vary by location

from

$625.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$692.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$448.99

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$447.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$363.99

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$109.99

AXLE SHAFT REPAIR BE

from

$75.93

Wheel Bearing

from

$48.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$46.99

Product Features:

Thrust washer kit
Fits GM 7.2″ IFS

from

$44.99

7.2IFS GM 01 & up Envoy disconnect housing seal.

Product Features:

Disconnect housing seal
Fits 2001 and up GM 7.2″ IFS in GMC Envoy

from

$44.91

Wheel Bearing

from

$24.29

BEARING

from

$17.99

Axle Seal

from

$14.99

SHAFT SEAL

from

$10.79

Product Features:

Brand may vary by location

from

$8.49

Product Features:

Brand may vary by location

Most Sold 2003 Chevrolet Express 1500 Differentials

Explore our best-selling Chevrolet parts for the 2003 Express 1500 among 282 OEM and aftermarket options starting from $1.99.

show more show less

from

$14.49

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$12.99

High Performance Motor Oil API LICENSED MOTOR OIL Royal Purple High Performance Motor Oil combines premium base oils with proprietary additive technologies to create a high performance synthetic engine oil that optimizes performance and protection. Royal Purple High Performance Motor Oils carry the current API and ILSAC engine oil licenses, as well as the GM dexos1 gasoline engine oil approval. ILSAC GF-6 AND GM DEXOS1 Modern gasoline direct injection (GDI) engines have achieved levels of power and fuel economy never before possible in passenger car engines. As a result, smaller engines operate at much higher loads across all engine speeds. This has caused increased wear in critical areas of the engine, and created a destructive phenomenon called low-speed pre-ignition (LSPI). The unique, state-of-the-art additive technology in Royal Purple High Performance engine oils is designed specifically to address these issues, and help engines maintain performance and reliability.

Product Features:

Better Wear Protection
Increased Protection against Low Speed Pre-Ignition
Increased Fuel Efficiency
Better Protection for Vehicle Exhaust Emissions Equipment
Improved Compatibility with Fuels Containing Ethanol
Superior Corrosion Protection
Made in USA

from

$35.99

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$7.49

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$153.99

Product Features:

GM10 BOLT 8.5″ 30 SPL INTERNAL KIT 1988-1999 (OPEN)

from

$235.99

Product Features:

GM 10BL 8.5 R/P 3.42A MG FRT/REAR

from

$9.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$14.99

Valvoline Multi-Vehicle Transfer Case Fluid is a full synthetic product meeting the performance needs for transfer cases recommending Ford XL-12 and GM Auto Trak II specifications or ATF fluids (DEX/MERC, ATF +4, etc).

Product Features:

Recommended for use in most Ford, GM and FCA (Dodge, Jeep) models
Formulated to help prevent gear wear and protect against rust and corrosion
Formulated to deliver enhanced protection against deposits
Helps provide better protection during extreme operating conditions

from

$10.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$103.99

The National® bearing & seal kit includes all the components required to complete the repair.

Product Features:

COMPLETE SOLUTION — Includes everything needed to complete the repair
STRONG AND DURABLE — Controlled heat treatment process for strength and durability
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING¿-¿Comprehensive¿testing throughout design and development processes by National engineers for quality you can count on¿
RIGOROUS TESTING┐-┐Comprehensive┐testing throughout design and development processes by National engineers for quality you can count on┐
Professional technicians know they can depend on National

from

$99.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT-BRG & SEAL GM 8.5 10 BOLT – ’99 & UP LATER

from

$157.99

BEARING GASKET & SEAL KIT, 10 BOLT GM ’99 AND UP MASTER KIT

from

$11.79

Formulated to meet the specific requirements of Toyota, Lexus, and scion vehicles equipped with conventional (non-CVT) transmissions that require the use of ATF T-IV. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF T-IV is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:

Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
Provides superior cleanliness, maintaining the transmission free of sludge and varnish deposits
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
Advanced anti-wear technology provides maximum protection to gears and bearings
Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking

from

$241.99

Product Features:

GM 10BL 8.5 R/P 3.73A MG FRT/REAR

from

$23.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$5.99

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$16.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$231.99

This Motive Gear Differential Rebuild Kit includes all of the parts required to rebuild your stock open differential. The gears are lapped for quiet operation. Includes spider and side gears, cross shaft, lock pin or bolt and thrust washers.

Product Features:

GM8.6″ INTERNAL KIT (OPEN) 30 SPL. MID 2000-2008

from

$243.99

Product Features:

GM 10BL 8.5 R/P 3.73 MG FRT/REAR

from

$52.99

DIFF COVER KIT

from

$176.99

Product Features:

GM9.5″ INTERNAL KIT (OPEN) 33 SPL. FRONT & REAR

from

$51.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$8.49

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$2.49

Product Features:

RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND

from

$7.99

Differential Cover B

from

$6.99

Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:

Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
7/16″ x 20

from

$5.29

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles.
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$9.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$12.99

Specifically designed to minimize wear and restore lost performance in engines with more than 75,000 miles
Formulated with robust zinc/phosphorus anti-wear compounds combined with royal purple’s proprietary additive technology
Hmx is chemically enhanced to revitalize hardened seals, reducing oil consumption common in high-mileage engines
Reduces friction and metal-to-metal contact for peak engine performance
Also provides outstanding oxidation resistance to safely extend oil drain intervals, and an ionic attraction to metal surfaces, providing protection and minimizing wear at start-up
High-Mileage Formula: Specifically designed for engines with more than 75,000 miles, this full synthetic engine oil helps minimize wear and restore lost performance.

from

$4.99

8.6″ GM standard Open side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits GM 8.6″

from

$16.99

Product Features:

Brand may vary by location

from

$3.99

from

$4.29

from

$221.99

from

$48.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (includes Supershims)

Product Features:

Fits GM 8.5″ rear
Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

from

$108.39

Differential Cover with Hardware Included

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$209.99

10 Bolt open spider gear set for ’00-’06 8.6″ GM with 30 spline axles. Fits case with one large window and one small window. A new carrier case will be needed for ’99 vehicles in order to use this spider gear set. This spider gear set fits casting number

Product Features:

Fits 2000-2006 GM 8.6″ with open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$74.99

Chrome cover for 8.6″, 8.5″ and 8.2″ GM rear.

Product Features:

Fits GM 8.2″, 8.5″ and 8.6″
Chrome

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
7/8″ x 14 thread
1 1/4″ socket

from

$12.99

Product Features:

KIT SHIM

from

$214.99

Product Features:

Spider gear kit
Fits GM 8.5″ 30 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$57.99

Product Features:

Crush sleeve eliminator kit for GM 8.5″, 8.6″ and Chrysler 9.25″ rear

Top-Rated Drivetrains Brands For Your 2003 Chevrolet Express 1500

Shop for the best-rated brands offering Drivetrains and other products for your 2003 Chevrolet Express 1500s. Below you’ll find some of our best rated Drivetrains from Valvoline, Royal Purple, and Moog, and more. Drivetrains from these brands that fit a 2003 Express 1500 start at just $11.99 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Valvoline 2003 Chevrolet Express 1500 Drivetrains

When it comes to maintaining or upgrading your 2003 Chevrolet Express 1500, using quality Drivetrains is essential to ensure durability and a perfect fit. Valvoline ticks all of those boxes. We offer a wide selection of Valvoline Drivetrains, specifically designed for the 2003 Chevrolet Express 1500. With over 4 Valvoline brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $12.49, with an average price of just $19.49. Plus, with over 55 customer reviews and an average rating of 5 stars, you can trust that our Valvoline Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$14.49

(2)

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

“I’ve used this in my 2005 2500HD since I bought the truck with 20k on it now at 280k changed every other year maybe 40k I’d put on in two years,
I pu”

from
$35.99

(17)

DEX/MERC Automatic Transmission Fluid, 1 Gallon

“Equivalent to oem”

from
$12.49

This product is not rated

High Performance Transmission & Differential Gear Oil: Conventional 75W-90, 1 Quart

“”

Popular Royal Purple 2003 Chevrolet Express 1500 Drivetrains

Royal Purple auto parts is one of the highest quality Drivetrain brands in the market. Any 2003 Chevrolet Express 1500 owner should feel confident when installing genuine Royal Purple parts in their vehicle. To ensure the best fit and performance for your 2003 Express 1500, Advance Auto Parts carries a full inventory of 2 Royal Purple Drivetrains. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Royal Purple Drivetrains range up to $12.99, plus, with more than 82 customer reviews and an impressive 5 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from
$12.99

(82)

High Performance SAE 5W30 Synthetic Motor Oil, API Certified, 1 QT

“best oil”

from
$12.99

This product is not rated

HMX SAE 5W-30 High-Mileage Synthetic Engine Oil (1 Quart)

“”

FAQs for 2003 Chevrolet Express 1500 Drivetrains

Which Drivetrains are best-sellers for 2003 Chevrolet Express 1500s?

Out of 392 Drivetrains that fit 2003 Chevrolet Express 1500s, the following parts are the top sellers:

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (12079201) – $14.49
High Performance SAE 5W30 Synthetic Motor Oil, API Certified, 1 QT (8070001) – $12.99
Differential Cover Gasket (5185823) – $9.99

What’s the price range for 2003 Chevrolet Express 1500 Drivetrains?

Drivetrain prices for the 2003 Chevrolet Express 1500 start at $1.99 and go up to $2,369.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2003 Chevrolet Express 1500?

The average price for Drivetrains for the 2003 Chevrolet Express 1500 is $203.52. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Chevrolet Express 1500 model years?

Yes, we currently carry Drivetrains for 18 model years of Chevrolet Express 1500s between 1996 and 2014. Drivetrains are bought most frequently for the following model years: 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007, and 2006.

What are the cheapest Drivetrains for my 2003 Chevrolet Express 1500?

The cheapest 2003 Chevrolet Express 1500 Drivetrains we carry in stock are:

Differential Ring Gear Bolt (10282159) – $1.99
Ring Gear Bolt (20520168) – $2.49
Differential Ring Gear Bolt (10282141) – $2.49
Differential Pinion Gear Washer (10282533) – $2.59
Differential Cross Shaft (10282201) – $2.79

What are the top-rated Drivetrains that fit the 2003 Chevrolet Express 1500?

Out of 3,652 reviews by customers, our 2003 Chevrolet Express 1500 Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 2003 Chevrolet Express 1500 and their top-rated products:

Universal Joints
- Universal Joint Strap Kit (10198342) – $15.99
- Greaseable Premium Universal Joint (10086738) – $26.99
- Universal Joint Strap Kit (10086946) – $11.99
Spindles
- Universal Joint Strap Kit (10198342) – $15.99
- Greaseable Premium Universal Joint (10086738) – $26.99
- Universal Joint Strap Kit (10086946) – $11.99
Differentials
- Universal Joint Strap Kit (10198342) – $15.99
- Greaseable Premium Universal Joint (10086738) – $26.99
- Universal Joint Strap Kit (10086946) – $11.99

What types of Drivetrains do you sell for my 2003 Chevrolet Express 1500?

As of 2/5/25, these are some of the most in-demand types of Drivetrains for a 2003 Chevrolet Express 1500:

Can I get help with 2003 Chevrolet Express 1500 Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Drivetrains and more.

What is your return policy for Chevrolet Express 1500 Drivetrains?

Advance Auto Parts keeps returns simple. For new Chevrolet Express 1500 Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

2003 Chevrolet Express 1500 Drivetrains

MTC – Differential Drain P (Part No.J7065587755MTC)

Pro-King – Shim Kit (Part No.741A200)

Dorman – Rear Axle Shaft Kit (Part No.630-022)

National – Bearings (Part No.M88010)

Motive Gear – Pinion Nut (Part No.1260823)

Dorman – Spindle Washer – I.D. 25.3 mm O.D. 44.2 mm Thickness 5.2 mm (Part No.618-057.1)

National – Shaft Repair Sleeve (Part No.99174)

National – Multi Purpose Bearing (Part No.HB-108-D)

Driveworks – Taper Bearing Cup (Part No.S-LM-501314)

Royal Purple – HMX SAE 5W-30 High-Mileage Synthetic Engine Oil (1 Quart) (Part No.11744)

Yukon Gear – 8.5" & 8.2" GM Carrier Installation Kit (Part No.57008)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6064)

Dorman – Spindle Washer – I.D. 25.3mm O.D. 44.2mm Thickness 5.2mm (sold by each) (Part No.618-057)

Yukon Gear – Adjuster Lock Bolt For Left Hand Case Half Of 7.2" And 9.25" GM IFS (Part No.33244)

Dorman – Rear Drive Shaft (Part No.936-096)

Yukon Gear – Thrust Washer Kit For GM 7.2" IFS Stub Shaft (Part No.33526)

Yukon Gear – Dura Grip Positraction For GM 9.5" With 33 Spline Axles (Part No.26025)

Dorman – Differential Pinion Yoke Assembly (Part No.697-549)

Yukon Gear – Yoke For ’98 And Newer GM 9.5" With A 1350 U/Joint Size And Triple Lip Design (Part No.41070)

Motive Gear – Differential Gear Install Kit (Part No.GM9.5IKL)

Yukon Gear – Cross Pin Shaft For GM 9.5", Fits Standard & Dura Grip Or Eaton Posi Carrier (Part No.33205)

Yukon Gear – Redi Sleeve For GM 8.5", 9.5" & 8.2" Bop Yokes (Part No.30229)

Yukon Gear – Super Carrier Shim Kit For GM 9.5" (Part No.55003)

National – Multi Purpose Seal (Part No.710664)

FAG US – SHAFT SEAL (Part No.SS2685)

Yukon Gear – Standard Open And Gov-Loc Cross Pin Bolt With M10X1.5 Thread For 9.5" And 9.25" GM IFS (Part No.33342)

Yukon Gear – Pinion Install Kit For GM 8.5" Differential (Part No.13069)

Motive Gear – Differential Timken Bearing And Pinion Seal Kit (Part No.R10RBSKT)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.492-10)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.534G)

Driveworks – Universal Joint (Part No.DW-534G)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.530-10)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.234)

Spicer – Universal Joint (Part No.5-795X)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.232)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.235)

Driveworks – Universal Joint (Part No.DW-331)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.231)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.331)

Spicer – Universal Joint (Part No.5-3147X)

Driveworks – Universal Joint (Part No.DW-235)

Dorman – Help – U-Joint Repair Kit (Part No.81001)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.331C)

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

Spicer – Lube For Life Non Greasable U-Joint (Part No.K1010991357SPI)

Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)

Yukon Gear – Yoke For ’98 And Newer GM 9.5" With A 1350 U/Joint Size And Triple Lip Design (Part No.41070)

Yukon Gear – Mechanics 3R Lifetime Series U/Joint (Part No.42020)

GMB – Universal Joint – Greasable (Part No.K1010481404GMB)

Yukon Gear – 7.5" And 8.5" GM Rear U/Joint Strap, Mech 3R (Part No.41201)

Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)

Yukon Gear – Yoke For GM 8.5" With A 1310 U/Joint Size (Part No.41086)

Yukon Gear – Forged Yoke For GM 8.5" With A 1350 U/Joint Size (Part No.41093)

Yukon Gear – 1350 To Mechanics 3R Adaptor U/Joint (Part No.42001)

Spicer – Universal Joint (Part No.5-1350-1X)

Yukon Gear – Mechanics 3R U/Joint (Part No.42014)

ACDelco – Professional U-Joint (Part No.K1010577082ACD)

Autopart International Inc – U Joint (Part No.K10102054143API)

Yukon Gear – Dana 60, Dana 70, 1350, 1410, 10.25", And 9.5" U-Joint Strap Kit (Part No.41193)

Yukon Gear – U/Joint Strap Bolt For 14T, 7.5", And 8.5" GM (Part No.33351)

Sealed Power – Engine Balance Shaft Bearing (Part No.3204DR)

Felpro – TRANSFER CASE GASKET SET (Part No.72770)

National – Bearings (Part No.M88048)

National – Bearings (Part No.M88010)

Dorman – Transfer Case Gasket (Part No.917-562)

National – Multi Purpose Seal (Part No.4503N)

ACDelco – Vehicle Speed Sensor (Part No.19302667)

Carquest Premium – Vehicle Speed Sensor (Part No.SBA3658)

Dorman – Transfer Case Gasket (Part No.J7133703729DOR)

National – Bearings (Part No.SCH-78)

Dorman – Transfer Case Housing Adapter (Part No.926-890)

Dorman – Transfer Case Adapter O-Ring (Part No.926-831)

USA Standard Gear – TCase Adapter Gasket (Part No.74586)

National – Multi Purpose Seal (Part No.710682)

National – Multi Purpose Seal (Part No.710664)