from

$18.99

Product Features:

Side gear thrust washer
Fits Toyota Tacoma and T100

from

$78.99

Bearing race driver for Toyota 7.5″, 8″ rear. (TOY32307). No return.

Product Features:

Bearing race driver
Fits 32307 race
All steel construction

from

$229.99

Product Features:

TOY 10BL 7.5 R/P 4.88 IFS MG NOT REV CUT

from

$13.49

Product Features:

KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$669.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 7.5″
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$120.81

Differential Pinion

from

$6.99

Ring Gear bolt for Toyota 7.5″, 8″, V6, Landcruiser reverse front & T100/Tacoma w/ factory locker. 11mm x 1.0.

Product Features:

Ring gear bolt for Toyota 7.5″, 8″, 8″ V6, Landrcuiser reverse rotation front and T100 and Tacoma rear with factory locking differential
11mm x 1.0

from

$8.99

Product Features:

Roll pin
Fits Toyota Tacoma and T100

from

$9.99

Toyota 7.5 pinion nut (M18x1.5).

Product Features:

Pinion nut for Toyota 7.5″
18mm x 1.5 thread

from

$12.99

Valvoline ATF for MERCON®V Applications is a high-quality transmission fluid meeting and exceeding the requirements of the Ford Mercon V specification which covers most Ford passenger cars and light-duty trucks (except those specifying MERCON®SP, MERCON®LV or Type F fluids), including Lincoln and Mercury, as well as most pre-2006 GM vehicles and many imports. Recommended for use in the following applications: MERCON®V, MERCON®, DEXRON®-III, DEXRON®-II, Caterpillar TO-2, Allison C-4. Other applications include Power steering fluid where a DEXRON® or MERCON® fluid is recommended. Suitable to use in Nissan Matic D, Matic J and Matic K.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$59.99

V6 Toyota solid crush sleeve replacement spacer kit, preload.

Product Features:

Crush sleeve eliminator kit for Toyota V6

from

$353.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Toyota 8″ clamshell front
Reverse rotation only
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$42.99

Product Features:

MINI-INSTL KT-TOYOTA 7.5″

from

$92.99

Toyota V6, T100 pinion seal w/factory elec. locker & factory yoke (OE replacement ONLY).Yukon Mighty seal.

Product Features:

Pinion seal
Fits toyota Tacoma and T100 with factory locker and Toyota V6

from

$276.99

Yukon small hole yoke for ’82 and older Toyota T100 and Tacoma (with locker) with 27 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota Tacoma and T100 with factory locking differential
27 spline

from

$494.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket. This kit fits applications with a 29 spline pinion.

Product Features:

Fits Toyota V6
29 spline only
Uses Koyo bearings and races
Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and gasket.

from

$8.51

Axle Seal

from

$10.99

V6 standard Open pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer
Fits Toyota V6

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$298.99

Product Features:

Cross pin shaft
Fits Toyota V6

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$782.99

Differential

from

$461.99

Yukon standard open spider gear kit for Toyota T100 & Tacoma with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Toytoa Tacoma and T100 open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin spider gear thrust washers.

from

$101.99

7.5″ V6 & 4cyl side shim kit (incl. 7 shims).

Product Features:

Carrier shim kit
Fits Toyota 7.5″

from

$469.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Toyota Tacoma and T100 rear without factory locking differential
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and silicone.

from

$92.99

When the thin-gauge steel corrodes on 4Runner and Tacoma truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.

Product Features:

Rear Differential Cover
Rear Differential Cover
When the thin-gauge steel corrodes on 4Runner and Tacoma truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.
Direct replacement – this weld-on differential cover directly replaces a corroded original cover on certain Toyota 4Runner and Tacoma trucks
Cost-effective repair – rather than buy a new axle, cut off the old cover and weld on this new one