2002 Toyota Tacoma Belts and Hoses

Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:

• Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
• Engineered to help address noise issues caused by the belt drive 
• Capable of handling more extreme temperatures and workloads

Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:

• Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
• Engineered to help address noise issues caused by the belt drive 
• Capable of handling more extreme temperatures and workloads

Radiator Hose

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• Resistant against wear, oil and heat.
• Strong tensile cords limit stretching.
• Supports higher horsepower loads.
• Made from high strength synthetic rubber.

Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.

Product Features:

• Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
• Precision molded teeth are protected by durable fabric facing for long life
• Tensile cord is engineered and tested for maximum load carrying capabilities
• Rubber backing resists abrasion, oil and heat

Dayco believes in a systems approach to maintenance and has a full line of serpentine belt kits that have been designed for the most popular light-duty applications, ensuring that whomever is completing the repair has all the parts needed. Dayco’s kit offers everything to service your front-end accessory drive with OE or equivalent components. This can include a premium tensioner with flat spring technology, durable pulley(s) with permanently lubricated bearings, a Dayco ela (stretch) serpentine belt, and the Dayco serpentine belt that provides extensive flexibility and longer service life, while handling higher workloads and temperatures.

Product Features:

• Engineered to match OE specifications with unique features that enhance vehicle performance and safety
• For vehicles that need a highly engineered drive belt and multiple parts for a thorough and proper repair
• Provides all the parts needed in one box, helping simplify installation

Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:

• Metal line kit
• For use in engine oil cooler applications
• Routes oil lines past exhaust manifolds
• Provides protection where standard hoses can fail

1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:

• Engine oil cooler hose
• Size: 1/2″ x 12′
• Designed for engine oil applications
• 12′ hose length accommodates most applications

This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and is made of high strength steel for improved life and durability. This pulley conforms to original equipment material, tolerances, and specifications. This part fits 2005-2016 Toyota Tacoma with 2.7L (Lower Idler with AC). Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.

The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.

Product Features:

• OE-Equivalent and a direct fit application.
• Precision bearing
• OE High quality pulley assembly
• Durable long life performance.

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

MacKay utilizes leading edge rubber technology and compounds, supported by in-house processes from rubber mixing to final product. This ensures hoses are made to the strict specifications required for the advanced motor vehicles of the 21st century. In vehicles of today, a hose has to be designed to withstand the stresses of modern, more compact but powerful engines that run hotter and at a higher pressure. Other factors include smaller engine compartments with poor heat dissipation, aggressive coolant additives, and stray (electrochemical) current that may be conducting through the cooling system. In short, the smaller but more powerful engines of today work a lot harder than the larger engines that were standard before. More heat is generated, higher burst pressures are required in cooling system components, and hoses have to be made tougher to withstand these demands. MacKay’s research and development chemists have developed new rubber formulations and manufacturing processes that ensure MacKay hoses meet the greater wear and heat demands created by modern engines. Rubber compounds used in automotive hoses today are predominantly synthetic rubber formulation. All MacKay coolant hoses are made from EPDM compounds that are highly resistant to ozone attack. Hoses made from some other rubber compounds may be subject to ozone deterioration.

Product Features:

• Excellent resistance to high temperatures
• Resists chemical attack (oils, fuels etc.)
• Excellent Ozone resistance
• Good resistance to abrasion
• High resistance to vibration

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair.

Product Features:

• Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles
• Durable construction – made of fuel-resistant materials to reduce future failure potential
• Regulatory compliant – built to meet emission and inspection standards
• Trustworthy value – backed by team of engineers and quality control experts in the United States

Pinion and axle seal puller. No return.

Product Features:

• Seal puller

Designed to replace original equipment manufacturer hose, Dayco Molded Radiator and Bypass Hose are built with knitted reinforcement and EPDM construction which provides high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and tem

Product Features:

• Made with synthetic EPDM rubber compounds that provide resistance to deterioration from ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C)
• The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose
• Meets SAE J20R4, Class D-1 requirements for improved service hose
• Meets Type EC electro-chemical requirements as specified in SAE J1684; which eliminates premature deterioration of the inner tube caused by the build up of static electric charges
• Limited Three Year Warranty

The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:

• Designed to meet OE specifications
• Not suitable for oil or heat transfer
• Meets SAE J20R4, Class D-2 requirements for improved service hoses
• This hose is designed to prevent splitting, ballooning, and elongation

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Heat and ozone resistant cover.
• Engineered to resist electrochemical degradation – the leading cause of hose failure.
• Re-engineered materials resist vacuum collapse. This reduces the need for internal springs in many applications.
• Meets SAE 20R4 and 20R3 Type EC Class D-1 and D-2 specifications.
• Temperature Rating: -40° F to 275° F (-40° C to 135° C) in coolant hose applications.
• Note: Gates recommends replacing standard worm drive and spring loaded clamps with Gates PowerGrip(R) SB Clamps each time a new coolant hose is installed.

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Radiator Hose

Providing reliable service in applications requiring molded hoses, the Dayco heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• Meets Type EC electro-chemical requirements as specified in SAE J1684

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications