2001 Volkswagen Beetle Power Steering Parts

CARDONE Remanufactured Power Steering Pumps are engineered to meet or exceed O.E. performance. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Every unit undergoes a hydraulic efficiency test to ensure reliable, long-lasting performance.

Product Features:

• All critical components (campacs, spool valves, etc.) are triple-tested to ensure product reliability.
• All units are built with 100 percent new O-rings and premium-grade HNBR seals to prevent leaks. HNBR does not break down at high temperatures like conventional seal material.
• Shafts are surfaced to precise specifications to eliminate premature seal wear and extend pump life.
• Units are supplied with 100 percent tested and calibrated pressure relief valves.
• Final pump assembly is computer-tested to measure pressure, bypass, fluid flow, valve operation, steering effort and noise to ensure reliable performance.
• As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
• Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.

New Power Steering Pumps are engineered to OE specifications. All units are carefully packaged to insure safe arrival at your door.

Premium-quality new power steering pump designed for dependability and reliability throughout the service life of the vehicle.

Product Features:

• All critical components are built to strict manufacturing specifications, which eliminates critical component failure that causes noise and leaks
• Exterior surfaces are finished with corrosion and rust resistant coatings to ensure an extended service life
• All components are 100% new and functionally tested to meet or exceed OE specifications for extended reliability
• Power steering pulley and reservoir included (when applicable) which eases installation and eliminates contamination in the system

Premium-quality remanufactured power steering pump designed for dependability and reliability throughout the service life of the vehicle.

Product Features:

• Every Unit is fully disassembled, cleaned, and inspected which ensures that defects are identified and corrected to allow for an extended service life
• All shafts and internal surfaces are examined, reconditioned, and polished which prevents premature failure of the unit
• All serviceable components are replaced with 100% new OE equivalent parts for reliability throughout the service life of the power steering pump
• All assembled units are 100% end-of-line tested for leaks, noise, and performance to ensure that the product has the same functionality as intended by the OE

CARDONE Remanufactured Rack and Pinions are re-engineered, built and tested to meet or exceed O.E. fit and performance. 100 percent new, O.E.-style o-rings and seals are installed to ensure leak-free, long-lasting performance. A final protective coating is applied and each unit is tested to guarantee a perfect fit and function.

Product Features:

• Protective coating applied to each unit to extend the life of the unit (where applicable).
• 100 percent performance testing to ensure perfect fit, function and reliable performance.
• 100 percent hydraulic testing for proper flow, leakage and performance ensures perfect fit and function (where applicable).
• Racks are surfaced to precise specifications to prevent leaking between chambers and extend unit life.
• 100 percent new O.E.- style o-rings and lip seals ensure leak-free and long-lasting performance (where applicable).
• All new spool valve seals and rack donut seals are installed to eliminate internal leaks and ensure reliable performance (where applicable).
• Valve housings have polished micro-finish sleeves for durability (where applicable).
• As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
• Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.

CARDONE Remanufactured Rack and Pinions are re-engineered, built and tested to meet or exceed O.E. fit and performance. 100 percent new, O.E.-style O-rings and seals are installed to ensure leak-free, long-lasting performance. A final protective coating is applied and each unit is tested to guarantee a perfect fit and function.

Product Features:

• Protective coating applied to each unit to extend the life of the unit (where applicable).
• 100 percent performance testing to ensure perfect fit, function and reliable performance.
• 100 percent hydraulic testing for proper flow, leakage and performance ensures perfect fit and function (where applicable).
• Racks are surfaced to precise specifications to prevent leaking between chambers and extend unit life.
• 100 percent new O.E.- style O-rings and lip seals ensure leak-free and long-lasting performance (where applicable).
• All new spool valve seals and rack donut seals are installed to eliminate internal leaks and ensure reliable performance (where applicable).
• Valve housings have polished micro-finish sleeves for durability (where applicable).
• As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
• Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.

Product Features:

• All critical components are built to strict manufacturing specifications, which eliminates critical component failure that causes noise and leaks
• Exterior surfaces are finished with corrosion and rust resistant coatings to ensure an extended service life
• All components are 100% new and functionally tested to meet or exceed OE specifications for extended reliability
• Rack teeth and pinion gears are machined for smooth operation, which guarantees correct steering feel and performance

Edelmann Elite power steering rack and pinions represent a step up in quality and performance over typical aftermarket brand power steering racks and are built to meet or exceed OE specifications for form, fit, and function. Designed and built with 100% new components and up-to-date designs provide for a better replacement part. Each rack is painstakingly engineered to not only eliminate commonly experienced failures caused by the OE design, but also incorporates the latest OE revisions and enhancements. Every rack has a unique Designated Numeric Asset identification number etched into the part, which verifies its authenticity and corresponds to an individualized test inspection report that is included with the product to confirm its level of quality.

Product Features:

• Every component is 100% completely new, never reused
• Each part’s unique DNA number and testing report provides confidence that the quality of your purchase is a verified fact, not just a concept
• Re-engineered designs like internal vent tubing fix traditional OE flaws and prevent premature, repeated failures. This commitment to “working out the bugs” in OE design will allow you to leave the risk of remanufactured units behind
• Complete with Inner Tie Rods & Boots
• Includes necessary hardware where applicable (o-ring, washers, etc…)
• Reinforced Packaging – Assures the product will arrive undamaged and ready for installation
• U.S. based A.S.E. Certified Technical Support stands ready to provide you with assistance

Direct Fit – to make installation easy; All units are USA Engineering Approved; PWR Pumps, Racks, Gears & Reservoirs are 100% tested for leaks, pressure, noise and function

Product Features:

• PWR Rack and Pinions are 100% NEW and Engineered In North America
• All PWR products are Designed, Tier-Manufactured, and Multi-Tested to meet or exceed OE Performance and Durability Requirements
• Features our EXCLUSIVE INDUSTRIAL GRADE PACKAGING, Tie Rod and Pinion Shaft Thread Protectors, Sealed Heavy Duty Plastic Enclosures, and Fluid Port Caps
• Includes: Factory Installed OE Mounting Bushings, Inner Tie Rods, Jam Nuts (as required), Precision Routed Fluid Transfer Lines, required Installation Seals, Hardware, and Instructions
• Precision Routed and Constructed Fluid Transfer Tubes
• Manufactured to meet or exceed OE requirements
• Engineering, test, and quality validation in the USA

AAE Remanufactured Hydraulic Power Steering Rack & Pinions include inner tie rods and new bellows secured by OE stainless steel clamps. AAE remanufactures all units in the USA. AAE uses only the highest quality OE components in our remanufacturing process and each unit undergoes a thorough inspection & testing procedure. Every unit is 100% tested to the strictest standards in the industry to ensure the customer is purchasing a quality product. Each unit is electrostatically painted with automotive grade paint to ensure long lasting finish to protect the unit in any driving condition. To ensure long life and OE performance & operation, please flush and fill steering system with OE approved power steering fluid.

Product Features:

• Manufactured Again Certified quality process
• Each unit is 100% hydraulically tested for pressure and flow.
• Racks are remanufactured with OE grade, high temperature seals and O-rings for increased durability and performance.

Premium-quality remanufactured power steering rack & pinion designed for dependability and reliability throughout the service life of the vehicle.

Product Features:

• Components are inspected and tested for straightness and structural integrity which eliminates critical component failure
• Rack shafts and housings are thoroughly inspected, cleaned, and painted which prevents corrosion and rust
• Sealing surfaces are polished, restored and checked for smoothness which helps to ensure that there will be no leaks for the extended service life of the unit
• All serviceable components are replaced with 100% new OE equivalent parts for reliability throughout the service life
• All assembled units are 100% end-of-line tested for leaks and performance to ensure that the product has the same functionality as intended by the OE

RCK & PIN

Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.

Product Features:

• Power steering oil cooler
• Size: 3/4″ x 2-1/2″ x 9″
• For vehicles with 3/8″ I.D. power steering return hose
• Removes destructive heat and prolongs power steering system life
• Compatible with OEM cooler systems
• Ultrasonically soldered for reliability
• 100% pressure testing to 150 PSI for quality assurance
• High efficiency turbulators

Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.

Product Features:

• Double lock beading with barbed tube end provides superior hose/coupling integrity
• Zinc coated tubes protect against rust and corrosion
• Heat/abrasion tubing protects vital areas

Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.

Product Features:

• Double lock beading with barbed tube end provides superior hose/coupling integrity
• Zinc coated tubes protect against rust and corrosion
• Banjo end lock tabs prevent hose end from loosening
• Heat/abrasion tubing protects vital areas

NEW P/S PULLEY