from

$234.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Toyota 8″ and 4 cylinder engine, 1986 and up with OEM ring and pinion set
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$109.99

Yukon 12 hole yoke for ’83 and newer Toyota 8″ and V6 with 27 splines. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Toyota 8″ and V6
27 spline
Round companion flange

from

$203.99

DiffrlCarrBng

from

$7.99

ZIP locker rear switch cover.

Product Features:

Cover for switch
Rear

from

$42.99

Product Features:

MINI-INSTL KT-TOYOTA 7.5″

from

$11.99

8″ standard Open side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits Toyota 8″ with 4 cylinder engine

from

$51.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Matched cup and cone components ensures consistent quality and outstanding performance
Industry leading coverage
Professional technicians know they can depend on National

from

$155.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

TOYOTA 8″ BRNG & SEAL MASTER KIT

from

$919.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

Fits Toyota V6 rear
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$129.78

Differential Bearing

from

$73.99

Differential Parts K

from

$403.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality.

Product Features:

Fits Toyota V6 rear
4.11 ratio
29 spline pinion

from

$15.99

Toyota Landcruiser pinion nut, coarse spline, LARGE. 22mm x 1.5mm.

Product Features:

Pinion nut
Fits Toyota Landcruiser with 10 spline pinion

from

$92.99

When the thin-gauge steel corrodes on 4Runner and Tacoma truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.

Product Features:

Rear Differential Cover
Rear Differential Cover
When the thin-gauge steel corrodes on 4Runner and Tacoma truck rear differential covers, the typical solution has been to replace the entire axle. This Dorman OE FIX weld-on solution allows direct replacement of only the failed cover.
Direct replacement – this weld-on differential cover directly replaces a corroded original cover on certain Toyota 4Runner and Tacoma trucks
Cost-effective repair – rather than buy a new axle, cut off the old cover and weld on this new one

from

$679.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 8″ with 4 cylinder engine
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$315.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$6.99

Toyota 7.5″, 8″, & V6 ring gear bolt retainer plate (5 needed).

Product Features:

Ring gear bolt retainer plate for Toyota 7.5″ 8″ and 8″ V6
5 needed

from

$39.99

8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:

Pinion depth shim kit for Toyota 7.5″, 8″ and V6

from

$419.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits Toyota V6 rear
4.11 ratio
29 spline pinion
Includes conversion yoke, seal, and pinion nut

from

$78.99

Product Features:

Seal housing for Toyota 8″ and V6
Includes o-rings

from

$55.99

Differential Pinion

from

$769.99

Limited Slip Dffrntl

from

$8.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes