2001 Lincoln Navigator Differentials

Side gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.750″ diameter cross pin shaft applications only

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9.75″
• Install 2011 and up Ring & Pinion into 2000 – 2007
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Premium Ring And Pinion Master Bearing And Installation Kit

Yukon pinion flange for ’09-’14 F150 & ’07-’14 Expedition 8.8″ IFS front.

Mini Spool for Ford 8.8″ with 31 spline axles and 7/8″ cross pin. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 8.8″ with 31 spline axles
• Provides 100% traction to both wheels at all times
• Installs into standard open carrier case

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

• 35 spline
• 8 x 3.96″ bolt pattern
• Cut to length design fits 40″-43.5″ applications
• Fits Dana Spicer 60, 70 and 80

Differential Pinion

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Cross pin bolt with 5/16 x 18 thread for 10.25″ Ford.

Product Features:

• Cross pin bolt for Ford 9.75″ and 10.25″ with c-clip axles
• 5/16″ x 18 thread

Yukon positraction internals for Ford 9.75″ Dura Grip posi, 34 spline. This kit fits Yukon Dura Grip ONLY. Will not work with factory trac Loc. This kit does not include clutches.

Product Features:

• Includes spider gears
• Includes two side gears, cross pin, cross pin bolt, and thrust washers
• Not OEM replacement

Ford 7.5″ & 8.8″ ring gear bolt, standard Open & TracLoc. 7/16″ x 20.

Product Features:

• Ring gear bolt for Ford 7.5″ and 8.8″
• 7/16″ x 20

If you venture off the beaten path, plow snow, or subject your truck or SUV to extreme conditions, this rugged rear differential cover will boost the protection and personality of your vehicle’s drivetrain. Instead of the vulnerable thin stamped steel original equipment cover, this diff cover is precision-engineered from thick ductile iron and boasts an attractive, corrosion-resistant wrinkle coating. Rocks, trail hazards and damaging debris can easily ding an ordinary differential cover, leading to oil leaks and cracks. Plow trucks undergo stress due to the weight of salters and plows, and the no-brakes impacts of hidden potholes, coupled with the corrosive nature of all the salt season after season. This cover also features two filler plugs, which can help ease the difficulties of filling through the factory plug located on the axle housing. The cover is also fitted with a drain plug to make fluid exchanges quick, easy, and remove the need for replacing the differential cover gasket. This extra-rigid replacement will help keep critical components safe while adding a serious cool factor, especially on lifted vehicles. Want to customize your diff even more? We’ve made the stainless steel Dorman logo plate removable so you can replace it with the plate and logo of your choice. The cover comes complete with all necessary bolts and plugs for a complete upgrade..

Product Features:

• Enhanced protection – ideal solution for off-road or snowplow vehicles that need additional protection from damaging rocks and other hazards that can crack an ordinary stamped steel differential cover.
• Precise fit – engineered to exacting specifications to match the fit and function of the original equipment differential cover for a seamless installation on specified Ford and Lincoln vehicles
• Upgraded repair – made from rigid ductile (also known as nodular) iron with an attractive, corrosion-resistant wrinkled finish, and includes required bolts and three plugs for a complete installation and simplified maintenance
• Customize it – includes a stainless steel Dorman logo plate that’s removable so you can replace it with the plate and logo of your choice

Yukon standard open spider gear kit for 9.75″ Ford with 34 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 9.75″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

Yukon Trac Loc positraction, Ford 8.8″, 31 spline, with Carbon Fiber clutches.

Product Features:

• Trac Loc positraction carrier case
• Includes spider gears
• Fits Ford 8.8″ with 31 spline axles
• Carbon fiber clutches

Pinion nut for GM 7.6″ IRS, 8.6″ IRS and some Ford 9.75″, Check threads for proper fit before before installing. 22mm x 1.5mm, Uses 32mm socket.

Product Features:

• Pinion nut for GM 7.6″ IRS and 8.6″ IRS and some Ford 9.75″
• 22mm x 1.5 thread
• 32mm socket

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

• Bearing race driver set
• 21 pieces
• All steel construction

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier

This differential disc kit is a low-cost, time-saving repair solution for the posi-traction function. They are designed to match the fit and performance of the original disc on specific vehicle years, makes and models.

Product Features:

• Direct replacement – this differential clutch kit provides the necessary components for repairing the original equipment on specific vehicles.
• Quality materials – all components are built for reliable longevity and performance.
• Smart solution – provides original equipment fit and function for a competitive price compared to original manufacturer
• Trustworthy quality – backed by team of designers and engineers in the United States

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 8.8″
• Includes carrier bearings and races and “super” carrier shim kit

8.8″ 31 spline standard Open case (7/8 X-PIN HOLE).

Product Features:

• Standard open carrier case
• Fits Ford 8.8″ with 31 spline axles
• Does not include spider gears
• 0.875″ cross pin shaft diameter

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• SOLID SPACER FORD 8.8″ & 9″

Product Features:

• Clutch kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
• 18 piece kit
• Steel clutches

Product Features:

• Clutch kit
• Fits Ford 9.75″
• Fits Yukon Dura Grip

Differential Bearing

CUP