2019 Lincoln Navigator Differentials

This differential mount bushing is precision-engineered and rigorously tested to provide reliable replacement for the original equipment on specific vehicles.

Product Features:

• Direct replacement – fits and performs like the original equipment on specific vehicles
• Reliable fit – precision-engineered to match the design and dimensions of original components
• Durable construction – manufactured to strict standards using sturdy, safe materials
• Rigorously tested – thorough quality control measures ensure longevity

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• KIT BRG & SEAL FORD 8.8″

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits 1997-1998 Ford 9.75″
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

Yukon standard open spider gear kit for 8.8″ Ford (and IFS) with 28 spline axles and 3/4″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 8.8″ open differential with 28 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon standard open spider gear kit for 8.8″ Ford with 31 spline axles and 7/8″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ with 31 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
• 0.875″ cross pin shaft diameter

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Product Features:

• FRD 10BL 8.8 R/P 3.27 MG

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits 2011 and up Ford 9.75″
• 9.75″ ring gear diameter
• 31 spline pinion
• 12 ring gear bolts
• 4.11 ratio

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits 2011 and up Ford 9.75″
• 9.75″ ring gear diameter
• 31 spline pinion
• 12 ring gear bolts
• 4.88 ratio

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-140 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations.
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Ford M2C-192A, GM 12346140, Chrysler MS-8985 and API GL-5

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

• Includes three quarts of Redline Shockproof oil

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

• Includes three quarts of conventional oil

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

• Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Product Features:

• FORD 9″ SOLID SPACER KIT

Product Features:

• SOLID SPACER FORD 8.8″ & 9″

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Value-priced seal meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Pinion seal for 10.25″ Ford.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 10.25″

Ford 7.5″ & 8.8″ ring gear bolt, standard Open & TracLoc. 7/16″ x 20.

Product Features:

• Ring gear bolt for Ford 7.5″ and 8.8″
• 7/16″ x 20

Product Features:

• Ford 7.5″, 8.8″ Ring Gear Bolt

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

• Forged From Premium Grade 8740 Chrome Moly Steel
• Heat Treated
• Nominally Rated At 200,000 Psi Tensile Strength
• Specially Hardened, Precision Ground Washers
• 0.75″ Underhead Length
• 200,000 PSI
• Sold As A Set

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Product Features:

• Spider gear kit
• Fits Ford 9.75″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ 31 spline Trac Loc positraction
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

High-quality Differential Carrier Shim Kit

Product Features:

• CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!