from

$8.02

Differential Drain P

from

$819.99

Hard use and poor lubrication can wear out a limited-slip differential. Restore original performance with this replacement differential carrier assembly that includes all-new spider gears, differential pins, clutches and carrier housing.

Product Features:

Direct replacement – this 30 spline limited-slip differential carrier fits in place of this vehicle’s original equipment carrier
100% new – this differential carrier uses all-new components, including spider gears, diff pin, pre-load spring pack and clutch pack
Ready to install – this differential carrier is shipped pre-assembled and ready to install
Ideal upgrade – can be used to upgrade from open differential to limited-slip in an existing differential

from

$209.99

NO RETURN NP516549 SET-UP Bearing (1 SINGLE Bearing) for Dana 80 , 11.5AAM , 4.375″ OD .

Product Features:

Set up bearing
Fits NP5516549 pinion bearing
Easily slips on and off pinion journal to allow for pinion depth adjustment

from

$604.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits 2011 and up GM and Chrysler 11.5″
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$12.79

Product Features:

High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$23.99

Product Features:

Cross pin bolt
Fits GM 9.5″ and 9.25″ IFS

from

$13.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$40.99

Product Features:

Side gear spacer sleeve
Fits GM 9.25″ IFS

from

$78.99

Eaton positraction shim kit for GM 14T.

Product Features:

Shim kit
Fits GM 10.5″ 14 bolt truck Eaton positraction

from

$6.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$44.99

11.5″ Chrysler & GM cover gasket.

Product Features:

Cover gasket
Fits GM and Chrysler 11.5″

from

$214.99

Product Features:

Spider gear kit
Fits GM 9.5″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$137.90

Differential Bearing

from

$37.99

Product Features:

Pinion nut for GM and Chrysler 11.5″
12 point 36mm socket

from

$299.99

Yukon yoke for GM 10.5″ 14 bolt truck, 1410, strap style. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 10.5″ 14 bolt truck
30 spline
1410 u-joint size
4.188″ snap ring span
1.188″ cap diameter
Outside snap ring design
Strap style

from

$449.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1998 and up GM 10.5″ 14 bolt truck
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$309.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$27.99

Product Features:

Brand may vary by location

from

$205.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:56 & UP

from

$98.99

Left hand carrier bearing adjuster for 9.25″ GM IFS.

Product Features:

Side adjuster
Fits 2010 and down GM 9.25″ IFS
Left hand side

from

$32.99

Adjuster lock bolt for left hand case half of 7.2″ and 9.25″ GM IFS.

Product Features:

Side adjuster lock bolt
Fits GM 7.2″ IFS and 9.25″ IFS

from

$591.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$26.99

Left hand adjuster lock nut for 9.25″ GM.

Product Features:

Side adjuster lock nut
Fits GM 9.25″

from

$5.99

Differential Cover B

from

$1485.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM and Chrysler 11.5″ with 30 spline axles
Clutch style positraction
Smooth design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$52.99

Product Features:

MINI INSTALL KIT GM9.2IFS 98 & ON

from

$329.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features: