2001 BMW M3 Engine Cooling Parts

Essential 2001 BMW M3 Engine Cooling Parts

NTK – Engine Coolant Temperature Sensor (Part No.EF0086)

Engine Coolant Temperature Sensor

from

$29.99
The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:
  • OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
  • FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
  • THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor
See More

Behr – Hella Service Visco® Engine Cooling Fan clutch (Part No.G5010236176BEH)

Hella Service Visco® Engine Cooling Fan clutch

from

$273.32
The Visco® clutch has the task of making the frictional connection to the fan wheel depending on the temperature, and influencing its speed. The drive torque is transferred by means of wear-free viscous friction to the fan wheel, the continuously variable speed of which is set on the basis of the operating conditions. In the case of the electrically-driven Visco® clutch, control takes place directly via sensors. Requirement-based cooling optimizes the coolant temperature, engine noise and fuel consumption.

Product Features:
  • Out of box, drop in replacements
  • Factory mounts for easy install
  • Exact fit
  • Reduced labor time
  • Higher customer satisfaction
See More

Carquest Premium – Radiator (Part No.432488)

Radiator

from

$143.99
Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:
  • Thermal tested under real-life temperature simulations
  • High tensile strength aluminum for maximum crimp strength
  • Plastic tanks are engineeredáwith integrated ribbingáfor addedástrength to withstand cracks, bowing and distortion during thermal cycles
  • Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
See More

Carquest Premium – COOLANT HOUSING (Part No.CH5541)

COOLANT HOUSING

from

$25.99
COOLANT HOUSING

Imperial – Adjustable Thermostatic Fan Control (Part No.226204)

Adjustable Thermostatic Fan Control

from

$55.99
Adjustable Thermostatic Fan Control. 160-210°F; push-in probe. Controls the operating temperature of Imperial electric fans. Operates up to 2 fans.

Product Features:
  • Adjustable thermostatic fan control
  • 160-210°F push-in probe
  • For use with Imperial electric fans
  • Probe installs into radiator fins
See More

Mahle – Thermostat (Part No.G4000278140MAH)

Thermostat

from

$86.60
Intelligent control systems from MAHLE are used in millions of applications worldwide to provide needs-based precision temperature control. Simple, effective, and tried and tested millions of times over: thermostat inserts from MAHLE provide meticulous regulation of coolant circuits around the world up to approximately 20 m3/h, and ensure ideal operating temperatures in light vehicles, trucks, stationary engines, and also agricultural and construction machinery. Wax elements are at the heart of all MAHLE thermostats and thermostat inserts. These maintenance-free, durable elements have proved their worth in millions of applications. MAHLE, Manufactures a wide range of variants with actuating forces of between 30 N and 2,500 N, small or large displacements, and for a large number of regulation ranges within a temperature span of -20C to +130C.

Product Features:
  • OE quality and design
  • Maintenance-free, durable elements
See More

Aftermarket – Radiator Mount Brack (Part No.G1021305091AFT)

Radiator Mount Brack

from

$11.90
Radiator Mount Brack

Elring – Water Pump O-Ring (Part No.G3059279771ELR)

Water Pump O-Ring

from

$4.11
Water Pump O-Ring

APA/URO Parts – Radiator Mount (Part No.G102075950APA)

Radiator Mount

from

$2.93
Radiator Mount

Imperial – Electric Fan – 10" Diameter (Part No.226110)

Electric Fan - 10" Diameter

from

$67.99
Electric fan with 10″ diameter. Imperial electric fans are reversible for push or pull operation and are designed with a thin, aerodynamic profile for applications with limited space.

Product Features:
  • Rapid-Cool® Thin-Line electric fans
  • 10″ Diameter
  • 650 CFM
  • Use as a pusher or puller fan
See More

Permatex – Water Pump & Thermostat RTV Silicone Gasket Maker, 0.5 OZ (Part No.22071)

Water Pump & Thermostat RTV Silicone Gasket Maker, 0.5 OZ

from

$6.99
Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings. Permatex Water Pump & Thermostat has the highest water-glycol resistance available in an RTV silicone.

Product Features:
  • Sensor-safe, noncorrosive RTV silicone gasket material
  • Formulated specifically for water pumps and thermostat housings
  • Highest water-glycol resistance available in RTV silicone
  • Superior adhesion and flexibility
  • Can be used as a gasket maker or dressing
See More

Carquest Premium – Engine Coolant Reservoir Cap (Part No.10246)

Engine Coolant Reservoir Cap

from

$21.99
Manufactured to meet all OEM specifications. Designed to be easy to install and remove. Manufactured from high quality components with proper relief and vacuum valves. Quality tested to stand up to even the most demanding automotive cooling systems.

Product Features:
  • Maintains proper cooling system pressure
  • Easy installation and removal
  • 100% tested to ensure proper pressure and longevity
  • Meets all OEM specifications
See More

APA/URO Parts – Water Pipe O-Ring (Part No.G2026248503APA)

Water Pipe O-Ring

from

$4.97
Water Pipe O-Ring

APA/URO Parts – Engine Cooling Fan Blade (Part No.G505028207APA)

Engine Cooling Fan Blade

from

$68.74
The APA/URO Engine Cooling Fan Blade is designed for specific vehicle fit, form, and function providing quiet dependable operation and longer service life.

Product Features:
  • Manufactured and tested to OEM specifications
  • Precision assembled and balanced with all NEW components for vibration free operation
  • OE Design and Technology insures ease of installation right out of the box
  • Manufactured in ISO and TS Certified facilities
See More

Geba – Geba Water Pump (Part No.G3000458068GEB)

Geba Water Pump

from

$192.79
The GEBA Water Pump contains no remanufactured components and is manufactured to ensure high efficiency and optimal cooling under all conditions. Geba maintenance free Bearings with ball and roller spindle bearings are designed for the highest axial and radial stresses. Up to Date unitized sealing technology ensure optimal leak tightness and longevity. All housings are examined before the assembly. This procedure guarantees high reliability and life span of GEBA water pumps.

Product Features:
  • OE-Equivalent and direct fit application.
  • 100% new with no remanufactured parts.
  • High quality cast aluminum.
  • Advanced bearing design for high axial and radial stresses.
  • Unitized sealing technology that ensures optimal leak tightness and longevity.
  • Optimum cooling performance and longevity.
See More

Graf – Water Pump (Part No.G3000458070GRA)

Water Pump

from

$144.20
The Graf Water Pump contains no remanufactured parts and is produced using an optimized all metal impeller design to assist in cooling under high RPM, and performance demands. Selection of raw materials, reliability of machinery and production processes, stringent controls throughout the production process, from melting to fitting, as well as reliability tests performed using equipment able to determine true performance, go to ensure this product is a real guarantee of safety and long life. The Graf water pump is centrifugal in type and comprises a bladed rotor linked by means of a shaft (which rotates on bearings housed in a support) to the drive gear; the seal between the pump and the motor block is guaranteed by a gasket, while the inside of the pump is guaranteed by a mechanical seal. Component parts: Impeller: supplies the fluid with the necessary energy to cover the entire cooling circuit. Mechanical seal: ensures fluid seal inside the pump. Bearing: transmits movement to the impeller and supports any ventilation parts. Entrainment part: for transmitting movement to the bearing. Pump body: supports the basic pump component parts and conveys the coolant in the motor block.

Product Features:
  • All the component parts fitted are pre-tested to evaluate durability, performance and reliability.
  • The bearings undergo a durability test equivalent to nominal lifespan and are then inspected to assess integrity.
  • The mechanical seals are tested in extreme coolant temperature conditions according to predefined cycles.
  • The shape of the impellers is optimized thanks to the use of prototypes on which flow and performance tests are performed.
  • On both the entrainment parts and the bodies, the choice of materials and/or technologies different to original ones is made on the basis of structural and mechanical tests.
  • After assembly all the pumps undergo seal tests on units that reject those with leaks above set limits.
See More

Carquest Premium – Engine Coolant Level Sensor (Part No.FFA1122)

Engine Coolant Level Sensor

from

$141.99
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.
See More

Febi – Coolant Level Sensor (Part No.G105021138FEB)

Coolant Level Sensor

from

$26.42
Coolant Level Sensor

ACM – Cooling Fan Blade (Part No.G505028207ACM)

Cooling Fan Blade

from

$56.94
Cooling Fan Blade

Wahler – Engine Coolant Thermostat O-Ring (Part No.G4030278158WAH)

Engine Coolant Thermostat O-Ring

from

$5.80
The Wahler Engine Coolant Thermostat O-Ring is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:
  • Seals the thermostat housing and helps prevent coolant from leaking from the engine for proper engine temperature
  • Premium Original Equipment replacement
  • Provides performance and dependability
  • Manufactured to meet OE specifications
See More

Elring – Water Pipe O-Ring (Part No.G2026551372ELR)

Water Pipe O-Ring

from

$1.60
Water Pipe O-Ring

Permatex – High-Torque, High-Vibration RTV Silicone Gasket Maker, 13 OZ (Part No.82195)

High-Torque, High-Vibration RTV Silicone Gasket Maker, 13 OZ

from

$26.99
Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:
  • High torque and rigidity
  • Sensor-safe, non-corrosive formula
  • OEM specified
  • Low-odor, non-corrosive formula
  • Ideal for closed spaced bolt patterns
See More

Vaico – Coolant Bleed Screw (Part No.G203275972VCO)

Coolant Bleed Screw

from

$53.39
Choosing from the comprehensive VIEROL product range means opting for outstanding quality. This is confirmed by the Q+ quality seal for parts in OEM quality MADE IN GERMANY. VIEROL AG is a leading automotive parts distributor located in Oldenburg, Germany. With the trademarks VAICO and VEMO are the service market leaders in more than 125 countries worldwide. As an internationally present automotive supplier, VIEROL AG specializes in electronic and electrical components for German and European vehicles. VIEROL AG quality brands VEMO and VAICO combine innovation and experience, technical expertise and practiced corporate values, commitment to precision and a passion for technology: the invisible, but unquestionable, optimal prerequisites for guaranteed product quality and globally recognized service. Choosing from the comprehensive VIEROL product range means opting for outstanding quality.
See More

Dorman – Brass Coolant Air Bleeder Screw (Part No.902-404HP)

Brass Coolant Air Bleeder Screw

from

$8.79
This engine coolant bleeder screw has been manufactured from durable material to prevent cooling system leaks. Matches the original screw for fit and function.

Product Features:
  • Upgraded material – this brass coolant air bleeder screw reduces future maintenance costs by replacing the original equipment plastic screw on specified BMW, Mini, Chrysler, Dodge, Jeep, and Ram vehicles.
  • Ideal solution – instead of wasting time wrestling with a deformed plastic screw head, this sturdy brass screw ensures easy, reliable removal and reuse.
  • Durable construction – made of quality brass for reliable performance and long service life
  • Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
See More

APA/URO Parts – Coolant Bleed Screw (Part No.G203275972APA)

Coolant Bleed Screw

from

$2.98
Coolant Bleed Screw

Permatex – The Right Stuff: Grey, 1 Minute Gasket Maker, 10 OZ (Part No.34310)

The Right Stuff: Grey, 1 Minute Gasket Maker, 10 OZ

from

$38.99
Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:
  • Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
  • Sensor-safe, non-corrosive, RTV silicone
  • Protects against leaks caused by vibration and thermal expansion
  • Meets performance specs of OE silicone gaskets
  • Quickly returns vehicle to service in just 1 minute
See More

2001 BMW M3 Engine Cooling Parts

Maybe you’re in the middle of a full rebuild of that 2001 BMW M3. Maybe you just need a couple of Engine Cooling Parts. Either way, Advance Auto Parts has 42 different Engine Cooling Parts in our inventory ranging from $1.60 to $724.99. That means you can find the exact parts or products you need to keep that 2001 BMW M3 running smoothly.

Engine Cooling Parts are only as good as their brand. We stock 21 different brands to make sure you have plenty of trusted parts to choose from for your 2001 BMW M3. Permatex, Imperial, and Carquest Premium are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Engine Cooling Parts for your 2001 BMW M3, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 425 reviews in this category, some of the top rated parts include Radiator Cap: 30 PSI with 4.1 stars and Thermostatic Fan Control – Preset with 3.0 stars.

So if you’re in the market for aftermarket Engine Cooling Parts to keep your 2001 BMW M3 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Engine Cooling Parts Brands To Make Your 2001 BMW M3 Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 2001 BMW M3 demands trusted brand parts and products to keep it running. Many trusted brands of Engine Cooling Parts make up Advance Auto Parts’ inventory, and all are ready to help make your M3 the best it can be. Be sure to browse some of our top Engine Cooling Parts brands and parts.

FAQs for 2001 BMW M3 Engine Cooling Parts

What are the most purchased Engine Cooling Parts for the 2001 BMW M3?

Out of 42 Engine Cooling Parts for the 2001 BMW M3, the most popular in our inventory are:
Adjustable Thermostatic Fan Control
from $22.99
(35)
Adjustable Thermostatic Fan Control
Engine Cooling Fan Controllers
Electric Fan - 12" Diameter
from $94.99
(38)
Electric Fan – 12" Diameter
Radiator Fan Motors
Adjustable Thermostatic Fan Control
from $55.99
(33)
Adjustable Thermostatic Fan Control
Engine Cooling Fan Controllers

What are the top-rated 2001 BMW M3 Engine Cooling Parts?

Top-rated Engine Cooling Parts for your 2001 BMW M3 based on customer reviews/ratings are:
Radiator Cap: 30 PSI
from $23.99
(14)
Radiator Cap: 30 PSI
“Fit my 2004 BMW 330xi. Came as described.”
Thermostatic Fan Control - Preset
from $38.49
(8)
Thermostatic Fan Control – Preset
“I’ve been using this kit for several years on my off road truck. It’s hooked up to a powerful flex-a-lite fan and handles the load with ease. I have”
Thermostatic Fan Control - Adjustable
from $62.99
(2)
Thermostatic Fan Control – Adjustable
“Need to find brass bushings to fit sensor to intake.Very easy to install!”